Clifford 6000 - Manuals - manualsarea.com

Page 2 - Wiring Description for the 4-Pin Connector; Wiring Description for the 22-Pin Connector; Pin Wire Color

Wiring Description for the 4-Pin Connector Pin Wire Color Con nects to 1 Green/Blue Ignition Output 2 White/Blue Starter Output 3 White/Brown Ignition Input 4 White/Green Starter Input Wiring Description for the 22-Pin Connector Pin Wire Color Con nects to 1 Gray/Blue Channel 4 output 2 Black Prewir...

Page 3 - Passenger Compartment Connections; and testing is complete.

Passenger Compartment Connections Control Unit and Extended Range Receiver The IntelliGuard 6000 con trol unit must be in stalled in side the ve hi cle. Un der no cir cum stances should the unit be in stalled un der the hood or other simi larly hos tile en vi ron ment. 1. Select an area behind the d...

Page 4 - Passenger Compartment Connections (Continued); the di ode band point ing to ward the switch.; Door Trigger/Parking light; Engine Bay Connections

Passenger Compartment Connections (Continued) Trunk Trigger Vehicles with a ground-switching trunk light will interface directly with the IntelliGuard 6000 (on positive switching Rolls-Royce vehicles,use a relay to invert polarity). The switch may be located in or near the trunk latch or at the trun...

Page 5 - Hood Trigger; Final Wiring Connections; Delayed; Remote Control Channel Assignments; Mas ter Re mote Control; Func tion

Engine Bay Connections (Continued) Hood Trigger Vehicles with a ground-switching hood light will interface directly with the IntelliGuard 6000 (on positive switching vehicles, use a relay toinvert polarity). The switch may be located in or near the hood latch or at the hood light. If a switch cannot...

Page 6 - Num ber of LED flashes be tween pauses

FACT—False Alarm Control and Test The system microprocessor automatically checks for another activated sensor or trigger before sounding the siren a second time, thuspreventing any further false alarms. If you wish to test FACT, simply,1. Arm the sys tem with the re mote con trol.2. Wait 10 seconds ...

Page 7 - must; Certificate of Installation; Programmable Features; bold; Using the CliffNet Wizard Pro; CliffNet Wizard Pro User’s Guide; Programming the User-Selectable Features; To select another feature

Certificate of Installation After installation and testing has been completed, you must fill in the Clifford Electronics Certificate of Installation . Programmable Features IntelliGuard 6000 comes from the factory with its features preprogrammed as noted in bold text in the tables on pages 8 and 9. ...

Page 8 - User-Programmable Features; NOT USED; SHOULD ONLY BE PROGRAMMED

User-Programmable Features User-Programmable Features (1 Chirp = OFF, 2 Chirps = ON) Fea ture Select Unmarked 1 Unmarked 2 Unmarked 3 Unmarked 4 ✱ 1 Add New Remote NOTE 1 Chirps (Off/On/Quiet*) (1 chirp/2 chirps/3 chirps) *Quiet chirps are only available with SSPS Siren AutoArming (On/Off) Arm/Disar...

Page 9 - Installer-Programmable Features; chirps indicating that the system is in installer-program mode.; Fea ture; Single/Double Lock Pulse; NOTE 2; be on a single button.; System Checklist & Troubleshooting; In step 1 of the; Important; Starter and Ignition Immobilization

Installer-Programmable Features To access the installer-programmable features, use the procedure defined in the User-Programmable section, but after completing step 4, continue to press and hold the ✱ side of the PlainView 2 Switch for another 10 seconds. You will hear three confirmation chirps indi...

Page 10 - Starter or Ignition Auto Im mo bi li za tion Cir cuit; door trig ger; NOTE: If the 20A fuse blows upon arm ing:; Cen tral Door Lock ing/Un lock ing

System Checklist & Troubleshooting (Continued) n Arm the IntelliGuard 6000 (either from inside or outside the vehicle) and wait 10 seconds. Turn the ignition to the “ON” position. o Engine does not respond and alarm triggers. This is the correct response, proceed to step 3. o Engine starts or cr...

Page 11 - Parking lights; Only one side flashes.; Only one door locks.; Door Lock ing/Un lock ing

System Checklist & Troubleshooting (Continued) Step 4.Test the park ing lights. Arm the sys tem. n Two flashes. This is the correct response, proceed to step 5. n One flash. If the parking lights flash only once, the IntelliGuard 6000 had pre vi ously AutoArmed it self pas sively and by press in...

Page 13 - while

System Checklist & Troubleshooting (Continued) Step 13.Test the AutoArming By pass fea ture. Disarm the system. Turn the ignition to the “ON” position, then turn the ignition “OFF.” n One Chirp. This is the correct response, wait 30 seconds after the interior lights have turned off to insure the...