Cisco VR-561 - Manuals

Cisco IOS Voice, Video, and Fax Commands: R Through Sh req-qos VR-565 Cisco IOS Voice, Video, Fax Command Reference req-qos To specify the desired quality of service to be used in reaching a specified dial peer, use the req-qos command in dial-peer configuration mode. To restore the default value fo...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh reset VR-566 Cisco IOS Voice, Video, Fax Command Reference reset To reset a set of digital signal processors (DSPs), use the reset command in global configuration mode. reset number Syntax Description Defaults No default behavior or values. Comm...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh resource threshold VR-567 Cisco IOS Voice, Video, Fax Command Reference resource threshold To configure a gateway to report H.323 resource availability to the its gatekeeper, use the resource threshold command in gateway configuration mode. To d...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh resource threshold VR-568 Cisco IOS Voice, Video, Fax Command Reference When any monitored H.323 resources exceed the threshold level defined by the high parameter, the gateway sends an RAI message to the gatekeeper with the AlmostOutOfResources...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh response-timeout VR-569 Cisco IOS Voice, Video, Fax Command Reference response-timeout To configure the maximum time to wait for a response from a server, use the response-timeout command in settlement configuration mode. To restore the default ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh response-timeout VR-570 Cisco IOS Voice, Video, Fax Command Reference session-timeout Sets the interval for closing the connection when there is no input or output traffic. settlement Enters settlement mode and specifies the attributes specific ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry-limit VR-573 Cisco IOS Voice, Video, Fax Command Reference retry-limit To set the maximum number of attempts to connect to the provider, use the retry-limit command in settlement configuration mode. To restore the default value, use the no...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry-limit VR-574 Cisco IOS Voice, Video, Fax Command Reference session-timeout Sets the length of interval for closing the connection when there is no input or output traffic. settlement Enters settlement mode and specifies the attributes spec...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry (SIP user-agent) VR-575 Cisco IOS Voice, Video, Fax Command Reference retry (SIP user-agent) To configure the number of retry attempts for Session Initiation Protocol (SIP) messages, use the retry command in SIP user-agent configuration mo...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring VR-576 Cisco IOS Voice, Video, Fax Command Reference ring To set up a distinctive ring for your connected telephones, fax machines, or modems, use the ring command in interface configuration mode. To disable the specified distinctive ring, ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring VR-577 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description destination-pattern Specifies either the prefix, the full E.164 telephone number, or an ISDN directory number (depending on the dial plan) to be used ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring cadence VR-578 Cisco IOS Voice, Video, Fax Command Reference ring cadence To specify the ring cadence for a Foreign Exchange Station (FXS) voice port, use the ring cadence command in voice-port configuration mode. To restore the default val...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring cadence VR-579 Cisco IOS Voice, Video, Fax Command Reference Command Modes Voice-port configuration Command History Usage Guidelines The patternXX keyword provides preset ring cadence patterns for use on any platform. The define keyword all...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring frequency VR-580 Cisco IOS Voice, Video, Fax Command Reference ring frequency To specify the ring frequency for a specified Foreign Exchange Station (FXS) voice port, use the ring frequency command in voice-port configuration mode. To resto...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring frequency VR-581 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description ring cadence Specifies the ring cadence for an FXS voice port on the Cisco MC3810 multiservice concentrator. ring number Specifies the numbe...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring number VR-582 Cisco IOS Voice, Video, Fax Command Reference ring number To specify the number of rings for a specified Foreign Exchange Office (FXO) voice port, use the ring number command in voice-port configuration mode. To restore the de...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh roaming (dial-peer) VR-584 Cisco IOS Voice, Video, Fax Command Reference roaming (dial-peer) To enable the roaming capability for the dial peer, use the roaming command in dial-peer configuration mode. To disable the roaming capability, use the ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh roaming (settlement) VR-585 Cisco IOS Voice, Video, Fax Command Reference roaming (settlement) To enable the roaming capability for a settlement provider, use the roaming command in settlement configuration mode. To disable the roaming capabilit...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh rtsp client session history duration VR-586 Cisco IOS Voice, Video, Fax Command Reference rtsp client session history duration To specify how long to keep Real Time Streaming Protocol (RTSP) session history records in memory, use the rtsp client...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh rtsp client session history records VR-587 Cisco IOS Voice, Video, Fax Command Reference rtsp client session history records To configure the number of records to keep in the RTSP client session history, use the rtsp client session history recor...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh rule VR-588 Cisco IOS Voice, Video, Fax Command Reference rule To apply a translation rule to a calling party number or a called party number for both incoming and outgoing calls, use the rule command in translation-rule configuration mode. To r...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh rule VR-589 Cisco IOS Voice, Video, Fax Command Reference Usage Guidelines When configuring your dial peers, you are provided with an option called the translation rule. This option applies a translation rule to a calling party number (Automatic...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh security VR-590 Cisco IOS Voice, Video, Fax Command Reference security To enable authentication and authorization on a gatekeeper, use the security command in gatekeeper configuration mode. To disable security, use the no form of this command. s...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh security VR-591 Cisco IOS Voice, Video, Fax Command Reference A RADIUS/TACACS+ server and encryption key must have been configured in Cisco IOS software for security to work. Only the first alias of the proper type will be identified. If no alia...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sequence-numbers VR-593 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description called-number (dial-peer) Enables an incoming VoFR call leg to get bridged to the correct POTS call leg when using a static FRF.11 trunk c...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh server (RLM) VR-594 Cisco IOS Voice, Video, Fax Command Reference server (RLM) To identify an RLM server, use the server RLM configuration command. To remove the identification, use the no form of this command server name-tag no server name-tag ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh server registration-port VR-596 Cisco IOS Voice, Video, Fax Command Reference server registration-port To configure the listener port for the server to establish a connection with the gatekeeper, use the server registration-port command in gatek...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh server trigger VR-597 Cisco IOS Voice, Video, Fax Command Reference server trigger To configure a static server trigger for external applications, use the server trigger command in gatekeeper configuration mode. To remove a single statically con...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh server trigger VR-598 Cisco IOS Voice, Video, Fax Command Reference In LCF submode, enter the following syntax: server trigger lcf gkid priority server-id server-ipaddress server-port In LRJ submode, enter the following syntax: server trigger lr...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh server trigger VR-599 Cisco IOS Voice, Video, Fax Command Reference The remote-ext-address argument is under the LCF trigger submode and has the following options: The endpoint-type argument is under the RRQ and URQ trigger submodes and has the ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session VR-600 Cisco IOS Voice, Video, Fax Command Reference session To associate a transport session with a specified session-group, use the session group command in backhaul session manager configuration mode. It is assumed that the server is ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol VR-601 Cisco IOS Voice, Video, Fax Command Reference session protocol To specify a session protocol for calls between the local and remote routers using the packet network, use the session protocol command in dial-peer configura...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol VR-602 Cisco IOS Voice, Video, Fax Command Reference The following example selects AAL2 trunking as the session protocol on a Cisco MC3810 multiservice concentrator: dial-peer voice 10 voatm session protocol aal2-trunk The follo...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol (Voice over Frame Relay) VR-603 Cisco IOS Voice, Video, Fax Command Reference session protocol (Voice over Frame Relay) To establish a Voice over Frame Relay protocol for calls between the local and remote routers via the packet...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol (Voice over Frame Relay) VR-604 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description called-number (dial-peer) Enables an incoming VoFR call leg to get bridged to the correct POTS call leg when usin...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol aal2 VR-605 Cisco IOS Voice, Video, Fax Command Reference session protocol aal2 To enter the voice-service-session configuration mode and specify AAL2 trunking on a Cisco MC3810 multiservice concentrator, use the session protoco...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol multicast VR-606 Cisco IOS Voice, Video, Fax Command Reference session protocol multicast To set the session protocol as multicast, use the session protocol multicast command dial-peer configuration mode. To negate this command ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoATM) VR-607 Cisco IOS Voice, Video, Fax Command Reference session target (VoATM) To specify a network-specific address for a specified VoATM dial peer, use the session target command in dial-peer configuration mode. To restore ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoATM) VR-608 Cisco IOS Voice, Video, Fax Command Reference Command History Usage Guidelines Use the session target command to specify a network-specific address or domain name for a dial peer. Whether you select a network-specif...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoATM) VR-609 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description called-number Enables an incoming VoFR call leg to be bridged to the correct POTS call leg. codec (dial-peer) Specifies the voice co...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoFR) VR-610 Cisco IOS Voice, Video, Fax Command Reference session target (VoFR) To specify a network-specific address for a specified VoFR dial peer, use the session target command in dial-peer configuration mode. To restore def...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoIP) VR-613 Cisco IOS Voice, Video, Fax Command Reference session target (VoIP) To specify a network-specific address for a specified VoIP dial peer, use the session target command in dial-peer configuration mode. To restore def...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoIP) VR-614 Cisco IOS Voice, Video, Fax Command Reference Defaults The default state for this command is enabled, with no IP address or domain name defined. Command Modes Dial-peer configuration Command History Usage Guidelines ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoIP) VR-615 Cisco IOS Voice, Video, Fax Command Reference session target dns:voice_router.cisco.com The following example configures a session target using DNS, with the optional $u$. wildcard. In this example, the destination p...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh session transport VR-616 Cisco IOS Voice, Video, Fax Command Reference session transport To configure the VoIP dial peer to use TCP or User Datagram Protocol (UDP) as the underlying transport layer protocol for Session Initiation Protocol (SIP) ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh set VR-617 Cisco IOS Voice, Video, Fax Command Reference set To create a fault-tolerant or non-fault-tolerant session-set with the client or server option, use the set command in backhaul session manager configuration mode. To delete the set, us...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh settle-call VR-619 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description session target Specifies a network-specific address for a specified dial peer.

Cisco IOS Voice, Video, and Fax Commands: R Through Sh settlement VR-620 Cisco IOS Voice, Video, Fax Command Reference settlement To enter settlement configuration mode and specify the attributes specific to a settlement provider, use the settlement command in global configuration mode. To disable t...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh settlement VR-621 Cisco IOS Voice, Video, Fax Command Reference session-timeout Sets the interval for closing the connection when there is no input or output traffic. show settlement Displays the configuration for all settlement server transacti...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh settlement roam-pattern VR-622 Cisco IOS Voice, Video, Fax Command Reference settlement roam-pattern To configure a pattern that must be matched to determine if a user is roaming, use the settlement roam-pattern command in global configuration m...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp VR-623 Cisco IOS Voice, Video, Fax Command Reference sgcp To start and allocate resources for the Simple Gateway Control Protocol (SGCP) daemon, use the sgcp command in global configuration mode. To terminate all calls, release all allocate...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp VR-624 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waitin...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp call-agent VR-625 Cisco IOS Voice, Video, Fax Command Reference sgcp call-agent To define the IP address of the default Simple Gateway Control Protocol (SGCP) call agent in the router configuration file, use the sgcp call-agent command in g...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp call-agent VR-626 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-d...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp graceful-shutdown VR-627 Cisco IOS Voice, Video, Fax Command Reference sgcp graceful-shutdown To block all new calls and gracefully terminate all existing calls (wait for the caller to end the call), use the sgcp graceful-shutdown command i...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp graceful-shutdown VR-628 Cisco IOS Voice, Video, Fax Command Reference sgcp quarantine-buffer disable Disables the SGCP quarantine buffer. sgcp request retries Specifies the number of times to retry sending “notify” and “delete” messages to...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp max-waiting-delay VR-629 Cisco IOS Voice, Video, Fax Command Reference sgcp max-waiting-delay To set the Simple Gateway Control Protocol (SGCP) maximum waiting delay to prevent restart avalanches, use the sgcp max-waiting-delay command in g...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp max-waiting-delay VR-630 Cisco IOS Voice, Video, Fax Command Reference sgcp restart Triggers the router to send an RSIP message to the SGCP call agent indicating that the T1 controller is up or down so that the call agent can synchronize wi...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp modem passthru VR-631 Cisco IOS Voice, Video, Fax Command Reference sgcp modem passthru To enable Simple Gateway Control Protocol (SGCP) modem or fax pass-through, use the sgcp modem passthru command in global configuration mode. To disable...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp request retries VR-635 Cisco IOS Voice, Video, Fax Command Reference sgcp request retries To specify the number of times to retry sending “notify” and “delete” messages to the Simple Gateway Control Protocol (SGCP) call agent, use the sgcp ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp request timeout VR-637 Cisco IOS Voice, Video, Fax Command Reference sgcp request timeout To specify how long the system should wait for a response to a request, use the sgcp request timeout command in global configuration mode. To restore ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp restart VR-639 Cisco IOS Voice, Video, Fax Command Reference sgcp restart To trigger the router to send a Restart in Progress (RSIP) message to the Simple Gateway Control Protocol (SGCP) call agent indicating that the T1 controller is up or...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp retransmit timer VR-641 Cisco IOS Voice, Video, Fax Command Reference sgcp retransmit timer To configure the Simple Gateway Control Protocol (SGCP) retransmission timer to use a random algorithm, use the sgcp retransmit timer command in glo...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp timer VR-643 Cisco IOS Voice, Video, Fax Command Reference sgcp timer To configure how the gateway detects the Real-Time Transport Protocol (RTP) stream lost, use the sgcp timer command in global configuration mode. To restore the default v...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp tse payload VR-645 Cisco IOS Voice, Video, Fax Command Reference sgcp tse payload To enable Inband Telephony Signaling Events (TSE) for fax and modem operation, use the sgcp tse payload command in global configuration mode. To restore the d...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show aal2 profile VR-647 Cisco IOS Voice, Video, Fax Command Reference show aal2 profile To display the ATM adaptation layer 2 (AAL2) profiles configured on the system, use the show aal2 profile command in privileged EXEC mode. show aal2 profile...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show aal2 profile VR-648 Cisco IOS Voice, Video, Fax Command Reference Printing all the Profiles in the system Profile Type: ITUT Profile Number: 1 SID Support: 0 Red enable: 1 Num entries: 1 Coding type: g711ulaw Packet length: 40 UUI min: 0 UU...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show atm video-voice address VR-649 Cisco IOS Voice, Video, Fax Command Reference show atm video-voice address To display the network service access point (NSAP) address for the ATM interface, enter the show atm video-voice address command in pr...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager group VR-650 Cisco IOS Voice, Video, Fax Command Reference show backhaul-session-manager group To display status, statistics, or configuration information for all available session-groups, use the show backhaul-sess...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager session VR-652 Cisco IOS Voice, Video, Fax Command Reference show backhaul-session-manager session To display various information for about a session or sessions, use the show backhaul-session-manager session comman...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active VR-655 Cisco IOS Voice, Video, Fax Command Reference show call active To display active call information for voice calls or fax transmissions in progress, use the show call active command in user EXEC or privileged EXEC mode. sh...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active VR-659 Cisco IOS Voice, Video, Fax Command Reference Tele <int>: tx:<tot>/<v>/<fax>ms <codec> noise:<l> acom:<l> i/o:<l>/<l> dBm 1 : 22021hs.1 +2263 pid:0 Answer wook song ac...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active VR-660 Cisco IOS Voice, Video, Fax Command Reference GapFillWithPrediction Duration of the voice signal played out with signal synthesized from parameters, or samples of data preceding in time, because voice data was lost or not...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call application voice VR-662 Cisco IOS Voice, Video, Fax Command Reference show call application voice To define the names of the audio files that the interactive voice response (IVR) script will play, the operation of the abort keys, the ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback cache VR-666 Cisco IOS Voice, Video, Fax Command Reference show call fallback cache To see the current Calculated Planning Impairment Factor (ICPIF) estimates for all IP addresses in cache, use the show call fallback cache com...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback cache VR-667 Cisco IOS Voice, Video, Fax Command Reference Router# show call fallback cache 10.14.115.53 Probe IP Address Codec ICPIF Reject Accept ----- ---------- ----- ----- ------ ------ 1 10.14.115.53 g729r8 0 0 2 1 activ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback config VR-668 Cisco IOS Voice, Video, Fax Command Reference show call fallback config To display the call fallback configuration, use the show call fallback config command in EXEC mode. show call fallback config Syntax Descrip...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback stats VR-669 Cisco IOS Voice, Video, Fax Command Reference show call fallback stats To display the call fallback statistics, use the show call fallback stats command in EXEC mode. show call fallback stats Syntax Description Th...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history VR-670 Cisco IOS Voice, Video, Fax Command Reference show call history To display the call history table for voice calls or fax transmissions, use the show call history command in user EXEC or privileged EXEC mode. show call hi...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history VR-674 Cisco IOS Voice, Video, Fax Command Reference 2 : 5996450hs.25 +-1 +3802 pid:100 Answer 408 tx:0/0 rx:0/0 1F (T30 T1 EOM timeout) Telephony : tx:38020/38020/0ms g729r8 noise:0dBm acom:0dBm 2 : 5996752hs.26 +-1 +3500 pid:...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history VR-675 Cisco IOS Voice, Video, Fax Command Reference CallDuration Length of the call, in hours, minutes, and seconds, hh:mm:ss. CallOrigin Call origin: answer or originate. ChargedUnits Total number of charging units applying t...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history VR-677 Cisco IOS Voice, Video, Fax Command Reference Related Commands VAD Specifies whether voice activation detection (VAD) was enabled for this call. VoiceTxDuration Duration of voice transmission from this peer to the voice ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history video record VR-678 Cisco IOS Voice, Video, Fax Command Reference show call history video record To display information about video calls, use the show call history video record command in privileged EXEC mode. show call histor...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history voice record VR-679 Cisco IOS Voice, Video, Fax Command Reference show call history voice record To display Call Detail Record (CDR) events in the call history table, use the show call history voice record command in privileged...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history voice record VR-680 Cisco IOS Voice, Video, Fax Command Reference Related Commands Table 29 show call history voice record Field Descriptions Field Description ConnectionID Global call identifier for this voice call. Media Medi...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call resource voice stats VR-681 Cisco IOS Voice, Video, Fax Command Reference show call resource voice stats To display resource statistics for an H.323 gateway, use the show call resource voice stats command in privileged EXEC mode. show ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call resource voice stats VR-682 Cisco IOS Voice, Video, Fax Command Reference Related Commands Table 30 show call resource voice stats Field Descriptions Statistic Definition Total channels Number of channels physically configured for the ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call resource voice threshold VR-683 Cisco IOS Voice, Video, Fax Command Reference show call resource voice threshold To display the threshold configuration settings and status for an H.323 gateway, use the show call resource voice threshol...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync conf VR-684 Cisco IOS Voice, Video, Fax Command Reference show call rsvp-sync conf To display the configuration settings for Resource Reservation Protocol (RSVP) synchronization, use the show call rsvp-sync conf command in pr...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync conf VR-685 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description call rsvp-sync Enables synchronization between RSVP and the H.323 voice signaling protocol. call rsvp-sync resv-timer Sets the tim...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync stats VR-686 Cisco IOS Voice, Video, Fax Command Reference show call rsvp-sync stats To display statistics for calls that attempted Resource Reservation Protocol (RSVP) reservation, use the show call rsvp-sync stats command i...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync stats VR-687 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description call rsvp-sync Enables synchronization between RSVP and the H.323 voice signaling protocol. call rsvp-sync resv-timer Sets the ti...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show cdapi VR-688 Cisco IOS Voice, Video, Fax Command Reference show cdapi To display the Call Distributor A pplication Programming Interface (CDAPI), use the show cdapi command in privileged EXEC mode. show cdapi Syntax Description This command...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show cdapi VR-689 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description isdn protocol-emulate Configures the Layer 2 and Layer 3 port protocol of a BRI voice port or a PRI interface to emulate NT (network) or TE (use...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ces clock-select VR-690 Cisco IOS Voice, Video, Fax Command Reference show ces clock-select To display the setting of the network clock for the specified port, use the show ces clock-select command in privileged EXEC mode. show ces slot/por...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show connect VR-691 Cisco IOS Voice, Video, Fax Command Reference show connect To display configuration information about drop-and-insert connections that have been configured on a router, enter the show connect command in privileged EXEC mode. ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers rs366 VR-693 Cisco IOS Voice, Video, Fax Command Reference show controllers rs366 To display information about the RS-366 video interface on the video dialing module (VDM), use the show controllers rs366 command in privileged EX...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers rs366 VR-694 Cisco IOS Voice, Video, Fax Command Reference ICSR Interrupt control and status register of the VDM. EXT Extended register of the VDM. T1 through T5 Timeouts 1 through 5 of the watchdog timer, in milliseconds. Dial ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers timeslots VR-695 Cisco IOS Voice, Video, Fax Command Reference show controllers timeslots To show the channel-associated signaling (CAS) and ISDN PRI state in detail, use the show controllers timeslots command in privileged EXEC...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers voice VR-697 Cisco IOS Voice, Video, Fax Command Reference show controllers voice To display information about voice-related hardware, use the show controllers voice command in privileged EXEC mode. Syntax Description This comma...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm VR-701 Cisco IOS Voice, Video, Fax Command Reference show csm To display the call switching module (CSM) statistics for a particular digital signal processor (DSP) channel or all DSP channels or for a specific modem or DSP channel, use ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm VR-703 Cisco IOS Voice, Video, Fax Command Reference Table 34 describes the significant fields shown in the display. Table 34 show csm voice Field Descriptions Field Description slot Slot where the VFC resides. shelf/slot/port Specifies...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm VR-704 Cisco IOS Voice, Video, Fax Command Reference device_status The status of the device. Possible values are as follows: • VDEV_STATUS_UNLOCKED—Device is unlocked (meaning that it is available for new calls). • VDEV_STATUS_ACTIVE_WD...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm VR-705 Cisco IOS Voice, Video, Fax Command Reference csm_state CSM call state of the current call (PRI line) associated with this device. Possible values are as follows: • CSM_IDLE_STATE—Device is idle. • CSM_IC_STATE—A device has been ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dial-peer video VR-708 Cisco IOS Voice, Video, Fax Command Reference show dial-peer video To display dial-peer configuration, use the show dial-peer video command in privileged EXEC mode. show dial-peer video [number] [summary] Syntax Descr...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dial-peer voice VR-710 Cisco IOS Voice, Video, Fax Command Reference Successful Calls = 0, Failed Calls = 0 Accepted Calls = 0, Refused Calls = 0 Last Disconnect Cause is “” Last Disconnect Text is “” Last Setup Time = 0 The following is sa...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number VR-712 Cisco IOS Voice, Video, Fax Command Reference show dialplan incall number To show which plain old telephone service (POTS) dial peer is matched for a specific calling number or voice port, use the show dialplan...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number VR-714 Cisco IOS Voice, Video, Fax Command Reference forward-digits 4 session-target = `', voice-port = `1/0/1:D', direct-inward-dial = enabled, digit_strip = enabled, register E.164 number with GK = TRUE Connect Time...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number VR-715 Cisco IOS Voice, Video, Fax Command Reference Related Commands digit_strip Whether digit stripping is enabled or disabled in the dial peer. Enabled is the default. session-protocol Session protocol to be used f...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan number VR-716 Cisco IOS Voice, Video, Fax Command Reference show dialplan number To show which dial peer is reached when a particular telephone number is dialed, use the show dialplan number command in privileged EXEC mode. show di...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show frame-relay vofr VR-719 Cisco IOS Voice, Video, Fax Command Reference show frame-relay vofr To display information about the FRF.11 subchannels being used on Voice over Frame Relay (VoFR) data link connection identifiers (DLCIs), use the sh...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show frame-relay vofr VR-720 Cisco IOS Voice, Video, Fax Command Reference The following is sample output from the show frame-relay vofr command when an interface is specified: Router# show frame-relay vofr serial0 interface vofr-type dlci cid c...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show frame-relay vofr VR-721 Cisco IOS Voice, Video, Fax Command Reference show frame-relay pvc Displays statistics about PVCs for Frame Relay interfaces. show voice-port Displays configuration information about a specific voice port. Command De...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper calls VR-722 Cisco IOS Voice, Video, Fax Command Reference show gatekeeper calls To show the status of each ongoing call of which a gatekeeper is aware, use the show gatekeeper calls command in privileged EXEC mode. show gatekeep...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper calls VR-723 Cisco IOS Voice, Video, Fax Command Reference Table 39 describes the significant fields shown in the display. Related Commands Table 39 show gatekeeper calls Field Descriptions Field Description LocalCallID Identific...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper endpoints VR-724 Cisco IOS Voice, Video, Fax Command Reference show gatekeeper endpoints To display the status of all registered endpoints for a gatekeeper, use the show gatekeeper endpoints command in EXEC mode. show gatekeeper ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper endpoints VR-725 Cisco IOS Voice, Video, Fax Command Reference Related Commands Type The endpoint type (for example, terminal, gateway, or MCU). F S—Indicates that the endpoint is statically entered from the alias command rather ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper gw-type-prefix VR-727 Cisco IOS Voice, Video, Fax Command Reference Table 41 describes the fields contained in the show gatekeeper gw-type-prefix sample output. Table 41 show gatekeeper gw-type-prefix Field Descriptions Field Des...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper servers VR-729 Cisco IOS Voice, Video, Fax Command Reference show gatekeeper servers To see a list of currently registered and statically configured triggers on this gatekeeper router, enter the show gatekeeper servers command in...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper status VR-731 Cisco IOS Voice, Video, Fax Command Reference show gatekeeper status To show overall gatekeeper status, including authorization and authentication status, zone status, and so on, use the show gatekeeper status comma...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper zone prefix VR-732 Cisco IOS Voice, Video, Fax Command Reference show gatekeeper zone prefix To display the zone prefix table, use the show gatekeeper zone prefix command in privileged EXEC mode. show gatekeeper zone prefix Synta...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper zone status VR-733 Cisco IOS Voice, Video, Fax Command Reference show gatekeeper zone status To display the status of zones related to a gatekeeper, use the show gatekeeper zone status command in privileged EXEC mode. show gateke...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper zone status VR-734 Cisco IOS Voice, Video, Fax Command Reference Table 44 describes the significant fields shown in the display. Related Commands Table 44 show gatekeeper zone status Field Descriptions Field Description GK name T...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gateway VR-735 Cisco IOS Voice, Video, Fax Command Reference show gateway To display the current gateway status, use the show gateway command in privileged EXEC mode. show gateway Syntax Description This command has no arguments or keywords...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm VR-737 Cisco IOS Voice, Video, Fax Command Reference show interface dspfarm To display digital signal processor (DSP) information on the two-port T1/E1 high-density port adapter for the Cisco 7200 series, use the show inte...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm VR-738 Cisco IOS Voice, Video, Fax Command Reference 30887 packets input, 616516 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 30921 ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm VR-739 Cisco IOS Voice, Video, Fax Command Reference Tx packets Number of transmit (tx) packets. Tx frags Number of tx packets that were fragmented. Curr_dsp_tx_queued Number of tx packets that are being queued at host DSP...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm VR-741 Cisco IOS Voice, Video, Fax Command Reference Interface resets Number of times an interface has been completely reset. Resetting can happen if packets queued for transmission were not sent within a certain interval....

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp VR-742 Cisco IOS Voice, Video, Fax Command Reference show mgcp To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp command in EXEC mode. show mgcp Defaults No defaults Command Modes EXEC Comman...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp VR-743 Cisco IOS Voice, Video, Fax Command Reference Table 46 describes the significant fields shown in the display. Table 46 show mgcp Field Descriptions MGCP Admin State...Oper State The administrative and operational state of the MG...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp connection VR-745 Cisco IOS Voice, Video, Fax Command Reference show mgcp connection To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp connection command in EXEC mode. show mgcp connection Sy...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp connection VR-746 Cisco IOS Voice, Video, Fax Command Reference Related Commands (P)ort The ports used for this connection. The first port is the local UDP port. The second port is the remote UDP port. (M)ode The call mode, where: 0—An...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp statistics VR-748 Cisco IOS Voice, Video, Fax Command Reference show mgcp statistics To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp statistics command in EXEC mode. show mgcp statistics Sy...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp statistics VR-749 Cisco IOS Voice, Video, Fax Command Reference Table 48 describes the significant fields shown in the display. Related Commands Table 48 show mgcp statistics Field Descriptions UDP pkts rx, tx The number of UDP packets...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp statistics VR-750 Cisco IOS Voice, Video, Fax Command Reference show mgcp connection Displays connection-related MGCP configuration information. show mgcp endpoint Displays endpoint-specific MGCP configuration information.

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show num-exp VR-751 Cisco IOS Voice, Video, Fax Command Reference show num-exp To show the number expansions configured, use the show num-exp command in privileged EXEC mode. show num-exp [dialed-number] Syntax Description Defaults No default be...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show num-exp VR-752 Cisco IOS Voice, Video, Fax Command Reference Table 49 describes the significant fields shown in the display. Related Commands Table 49 show num-exp Field Descriptions Field Description Dest Digit Pattern Index number identif...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots csm VR-753 Cisco IOS Voice, Video, Fax Command Reference show pots csm To show the current state of calls and the most recent event received by the call switching module (CSM) on the Cisco 800 series router, use the show pots csm comma...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots status VR-754 Cisco IOS Voice, Video, Fax Command Reference show pots status To display the settings of the telephone port physical characteristics and other information on the telephone interfaces of the Cisco 800 series, use the show...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots status VR-756 Cisco IOS Voice, Video, Fax Command Reference Table 50 describes the significant fields shown in the display. Related Commands Table 50 show pots status Field Descriptions Field Descriptions POTS Global Configuration Disp...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 calls VR-758 Cisco IOS Voice, Video, Fax Command Reference show proxy h323 calls To list each active call on the proxy, use the show proxy h323 calls command in privileged EXEC mode. show proxy h323 calls Syntax Description This ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call VR-759 Cisco IOS Voice, Video, Fax Command Reference show proxy h323 detail-call To display the details of a particular call on a proxy, use the show proxy h323 detail-call command in privileged EXEC mode. show proxy ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call VR-764 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description h323 qos Enables QoS on the proxy.

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 status VR-765 Cisco IOS Voice, Video, Fax Command Reference show proxy h323 status To display the overall status of a proxy, use the show proxy h323 status command in privileged EXEC mode. show proxy h323 status Syntax Descriptio...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group statistics VR-767 Cisco IOS Voice, Video, Fax Command Reference show rlm group statistics To display the network latency of the Redundant Link Manager (RLM) group, use the show rlm group statistics command in privileged EXEC mode....

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group statistics VR-768 Cisco IOS Voice, Video, Fax Command Reference Server Link Group[r2-server]: Open the link [10.1.1.1(Loopback1), 10.1.5.1]: last time occurred at 02:46:06.724, success=0(0%), failure=1 avg=0.000s, max=0.000s, min=...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group status VR-770 Cisco IOS Voice, Video, Fax Command Reference show rlm group status To display the status of the Redundant Link Manager (RLM) group, use the show rlm group status command in privileged EXEC mode. show rlm group group...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group status VR-771 Cisco IOS Voice, Video, Fax Command Reference Related Commands socket The status of the individual signaling link. Server Link Group[r2-server] The status of all signaling links configured under a particular RLM serv...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group timer VR-772 Cisco IOS Voice, Video, Fax Command Reference show rlm group timer To display the current timer values, use the show rlm group timer command in privileged EXEC mode. show rlm group group-number timer Syntax Descriptio...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rtsp client session VR-774 Cisco IOS Voice, Video, Fax Command Reference show rtsp client session To display cumulative information about Real Time Streaming Protocol (RTSP) session records, use the show rtsp client session command in privi...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rtsp client session VR-776 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description rtsp client session history duration Specifies the length of time the RTSP is kept during the session. rtsp client session history...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv0 failures VR-777 Cisco IOS Voice, Video, Fax Command Reference show rudpv0 failures To show SS7 Reliable User Datagram Protocol (RUDP) failure statistics, enter the show rudpv0 failures command in privileged EXEC mode. show rudpv0 fai...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv0 statistics VR-779 Cisco IOS Voice, Video, Fax Command Reference show rudpv0 statistics To show SS7 Reliable User Datagram Protocol (RUDP) internal statistics, enter the show rudpv0 statistics privileged EXEC command. show rudpv0 stat...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv1 VR-781 Cisco IOS Voice, Video, Fax Command Reference show rudpv1 To display Reliable User Datagram Protocol (RUDP) information, use the show rudpv1 command in privileged EXEC mode. show rudpv1 { failures | parameters | statistics } S...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv1 VR-784 Cisco IOS Voice, Video, Fax Command Reference TotalPacketsReceived 1047 TotalDataBytesSent 18048 TotalDataBytesReceived 18048 TotalDataPacketsSent 752 TotalDataPacketsReceived 752 TotalPacketsRetrans 122 TotalPacketsDiscarded ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show settlement VR-785 Cisco IOS Voice, Video, Fax Command Reference show settlement To display the configuration for all settlement servers and see the specific provider and transactions, use the show settlement command in privileged EXEC mode....

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show settlement VR-786 Cisco IOS Voice, Video, Fax Command Reference The following example shows transaction and state information about a specific settlement server: Router# show settlement 0 transactions Transaction ID=8796304133625270342 stat...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp connection VR-788 Cisco IOS Voice, Video, Fax Command Reference Related Commands Table 55 show sgcp connection Field Descriptions Field Description SGCP Admin State The administrative and operational state of the SGCP daemon. SGCP call...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp endpoint VR-789 Cisco IOS Voice, Video, Fax Command Reference show sgcp endpoint To see SGCP endpoints eligible for SGCP management, use the show sgcp endpoint command in EXEC mode. show sgcp endpoint [interface ds1 [ds0]] Syntax Descr...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp endpoint VR-790 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description show sgcp connection Displays all the active connections on the host router. show sgcp statistics Displays global statistics for the SGC...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp statistics VR-792 Cisco IOS Voice, Video, Fax Command Reference ModifyConn rx 0, successful 0, failed 0 DeleteConn tx 0, successful 0, failed 0 NotifyRequest rx 0, successful 0, failed 0 Notify tx 0, successful 0, failed 0 ACK tx 0, NA...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sip-ua VR-793 Cisco IOS Voice, Video, Fax Command Reference show sip-ua To display information and settings for the Session Initiation Protocol (SIP) User Agent (UA), use the show sip-ua command in privileged EXEC mode. show sip-ua {retry |...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 ccb VR-795 Cisco IOS Voice, Video, Fax Command Reference show ss7 mtp2 ccb To display SS7 MTP 2 Channel Control Block (CCB) information, use the show ss7 mtp2 ccb command in privileged EXEC mode. show ss7 mtp2 ccb [channel] Syntax ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 state VR-797 Cisco IOS Voice, Video, Fax Command Reference show ss7 mtp2 state To display internal SS7 Message Transfer Part level 2 (MTP 2) state machine information, use the show ss7 mtp2 state command in privileged EXEC mode. sh...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 state VR-798 Cisco IOS Voice, Video, Fax Command Reference Table 56 SS7 MTP 2 State Information Fields State Description Possible Values MTP2LSC Indicates the overall status of the link. OOS—The link is Out-of-Service. INITIAL_ALIG...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 state VR-799 Cisco IOS Voice, Video, Fax Command Reference MTP2AERM Indicates the status of the alignment error rate monitor state machine (AERM). IDLE—The state machine is inactive. MONITORING—Alignment error monitor is active. Th...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats VR-800 Cisco IOS Voice, Video, Fax Command Reference show ss7 mtp2 stats To display SS7 MTP 2 operational statistics, use the show ss7 mtp2 stats command in privileged EXEC mode. show ss7 mtp2 stats [channel] Syntax Descripti...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats VR-802 Cisco IOS Voice, Video, Fax Command Reference Table 57 SS7 OM Information Fields Field Description OMIACAlignAttemptCount OMIACAlignFailCount OMIACAlignCompleteCount Counts for Initial Alignment Control (IAC) attempts....

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats VR-803 Cisco IOS Voice, Video, Fax Command Reference OMT1_TMO_Count OMT2_TMO_Count OMT3_TMO_Count OMT4_TMO_Count OMT5_TMO_Count OMT6_TMO_Count OMT7_TMO_Count OMT8_TMO_Count OMTA_TMO_Count OMTF_TMO_Count OMTO_TMO_Count OMTA_TM...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 timer VR-804 Cisco IOS Voice, Video, Fax Command Reference show ss7 mtp2 timer To display durations of the SS7 MTP 2 state machine timers, use the show ss7 mtp2 timer command in privileged EXEC mode. show ss7 mtp2 timer [channel] N...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 variant VR-806 Cisco IOS Voice, Video, Fax Command Reference show ss7 mtp2 variant To display information about the SS7 MTP 2 protocol variant, use the show ss7 mtp2 variant command in privileged EXEC mode. show ss7 mtp2 variant [c...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm session VR-808 Cisco IOS Voice, Video, Fax Command Reference Related Commands Table 58 Session Manager Session Information Field Description Remote Host, Local Host Shows the IP address and port number for the session. retrans_t Show...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm set VR-809 Cisco IOS Voice, Video, Fax Command Reference show ss7 sm set To display information about the SS7 failover timer, use the show ss7 sm set command in privileged EXEC mode. show ss7 sm set Syntax Description There are no ar...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm stats VR-810 Cisco IOS Voice, Video, Fax Command Reference show ss7 sm stats To display SS7 Session Manager session statistics, use the show ss7 sm stats command in privileged EXEC mode. show ss7 sm stats Syntax Description There are...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show translation-rule VR-812 Cisco IOS Voice, Video, Fax Command Reference show translation-rule To display the contents of the rules that have been configured for a specific translation name, use the show translation-rule command in privileged ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show translation-rule VR-813 Cisco IOS Voice, Video, Fax Command Reference Examples The following example shows output for the show translation-rule command: Router# show translation-rule Translation rule address:0x61AB94F8 Tag name:21 Translati...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show translation-rule VR-814 Cisco IOS Voice, Video, Fax Command Reference translate Applies a translation rule to a calling party number or a called party number for incoming calls. translate-outgoing Applies a translation rule to a calling par...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc VR-815 Cisco IOS Voice, Video, Fax Command Reference show vfc To see the entries in the host-name-and-address cache, use the show vfc command in privileged EXEC mode. show vfc slot-number [technology] Syntax Description Defaults No defa...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc cap-list VR-816 Cisco IOS Voice, Video, Fax Command Reference show vfc cap-list To show the current list of files on the capability list for this voice feature card (VFC), use the show vfc cap-list command in user EXEC mode. show vfc sl...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc default-file VR-817 Cisco IOS Voice, Video, Fax Command Reference show vfc default-file To show the default files included in the default file list for a voice feature card (VFC), use the show vfc default-file command in user EXEC mode....

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc directory VR-818 Cisco IOS Voice, Video, Fax Command Reference show vfc directory To show the list of all files residing on a voice feature card (VFC), use the show vfc directory command in user EXEC mode. show vfc slot directory Syntax...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc version VR-820 Cisco IOS Voice, Video, Fax Command Reference show vfc version To show the version of the software residing on a voice feature card (VFC), use the show vfc version command in user EXEC mode. show vfc slot version {dspware...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show video call summary VR-821 Cisco IOS Voice, Video, Fax Command Reference show video call summary To display summary information about video calls and the current status of the Video Call Manager (ViCM), use the show video call summary comman...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice busyout VR-822 Cisco IOS Voice, Video, Fax Command Reference show voice busyout To display information about the voice busyout state, use the show voice busyout command in privileged EXEC mode. show voice busyout Syntax Description Th...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice busyout VR-823 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description busyout forced Forces a voice port into the busyout state. busyout monitor Places a voice port in the busyout monitor state. busyout sei...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call VR-824 Cisco IOS Voice, Video, Fax Command Reference show voice call To show the call status for voice ports on the Cisco router or concentrator, use the show voice call EXEC command. Cisco 2600 and 3600 series with Analog Voice ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call VR-825 Cisco IOS Voice, Video, Fax Command Reference For the Cisco MC3810 Multiservice Concentrator with Analog Voice Ports: For the Cisco MC3810 Multiservice Concentrator with Digital Voice Ports: Command Modes EXEC Command Hist...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call VR-826 Cisco IOS Voice, Video, Fax Command Reference The show voice call command provides the status at these levels of the call handling module: • Tandem switch • End-to-end call manager • Call processing state machine • Protoco...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call VR-827 Cisco IOS Voice, Video, Fax Command Reference sys252#show voice call 1/4 1/4 vtsp level 0 state = S_CONNECT vpm level 1 state = S_TRUNKED vpm level 0 state = S_UP router#***DSP VOICE VP_DELAY STATISTICS*** Clk Offset(ms): ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice dsp VR-828 Cisco IOS Voice, Video, Fax Command Reference show voice dsp To show the current status of all digital signal processor (DSP) voice channels, use the show voice dsp command in privileged EXEC mode. show voice dsp Syntax Des...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice dsp VR-829 Cisco IOS Voice, Video, Fax Command Reference The following is sample output from the show voice dsp command on a Cisco 1750 router: Router# show voice dsp DSP#0: state IN SERVICE, 2 channels allocated channel#0: voice port...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice permanent-call VR-830 Cisco IOS Voice, Video, Fax Command Reference show voice permanent-call To display information about the permanent calls on a voice interface, use the show voice permanent-call command in user EXEC or privileged ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice permanent-call VR-832 Cisco IOS Voice, Video, Fax Command Reference Table 63 describes the fields shown in these displays. Table 63 show voice permanent-call Field Descriptions Field Description state Current status of the call on thi...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-834 Cisco IOS Voice, Video, Fax Command Reference show voice port To display configuration information about a specific voice port, use the show voice port command in EXEC command. Cisco 1750 Router show voice port slot-number...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-835 Cisco IOS Voice, Video, Fax Command Reference For the Cisco 2600 and 3600 Series Router with Analog Voice Ports: For the Cisco 2600 and 3600 Series Router with Digital Voice Ports: For the Cisco MC3810 Multiservice Concent...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-836 Cisco IOS Voice, Video, Fax Command Reference For the Cisco MC3810 Multiservice Concentrator with Digital Voice Ports: For the Cisco AS5300 Access Server : For the Cisco AS5800 Universal Access Server: For the Cisco 7200 S...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-841 Cisco IOS Voice, Video, Fax Command Reference The following is sample output from the show voice port summary command for all voice ports on a Cisco MC3810 multiservice concentrator with an analog voice module (AVM): IN OU...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-842 Cisco IOS Voice, Video, Fax Command Reference InterDigit Pulse Duration Timing Pulse dialing interdigit timing, in milliseconds. Interdigit Time Out Amount of time the system waits for a subsequent input digit from the cal...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-843 Cisco IOS Voice, Video, Fax Command Reference The following example displays voice port configuration information for the digital voice port 0 located in slot 1, DS0 group 1: receEive and transMit Slot is 1, Sub-unit is 0,...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port VR-844 Cisco IOS Voice, Video, Fax Command Reference Table 65 describes the significant fields shown in the display. Table 65 show voice port Field Descriptions for the Cisco AS5800 Field Description Type of VoicePort Indicates t...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling VR-845 Cisco IOS Voice, Video, Fax Command Reference show voice trunk-conditioning signaling To display the status of trunk-conditioning signaling and timing parameters for a voice port, use the show voice...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling VR-847 Cisco IOS Voice, Video, Fax Command Reference Table 66 describes the significant fields shown in the display. Table 66 show voice trunk-conditioning signaling Field Descriptions Field Description cu...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling VR-848 Cisco IOS Voice, Video, Fax Command Reference Related Commands Command Description show dial-peer voice Displays the configuration for all VoIP and POTS dial peers configured on the router. show voi...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning supervisory VR-849 Cisco IOS Voice, Video, Fax Command Reference show voice trunk-conditioning supervisory To display the status of trunk supervision and configuration parameters for a voice port, use the show voice...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning supervisory VR-851 Cisco IOS Voice, Video, Fax Command Reference Table 67 describes the significant fields shown in the display. Related Commands Table 67 show voice trunk-conditioning supervisory Field Descriptions...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm active_calls VR-852 Cisco IOS Voice, Video, Fax Command Reference show vrm active_calls To display active-only voice calls either for a specific voice feature card (VFC) or for all VFCs, use the show vrm active_calls command in privileg...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm active_calls VR-853 Cisco IOS Voice, Video, Fax Command Reference Table 68 describes the significant fields shown in the display. Table 68 show vrm active_calls Field Descriptions Field Description slot Slot where voice card is installe...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm active_calls VR-854 Cisco IOS Voice, Video, Fax Command Reference Related Commands tot egress control Total number of control packets sent from the VoIP side of the connection to the PSTN side of the connection. tot egress data drops To...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices VR-855 Cisco IOS Voice, Video, Fax Command Reference show vrm vdevices To display detailed information for a specific digital signal processor (DSP) or a brief summary display for all voice feature cards (VFCs), use the show vr...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices VR-856 Cisco IOS Voice, Video, Fax Command Reference tot ingress control = 1194 tot ingress data drops = 0 tot ingress control drops = 0 tot egress data = 39722 tot egress control = 1209 tot egress data drops = 0 tot egress con...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices VR-857 Cisco IOS Voice, Video, Fax Command Reference capability list map Bitmaps for the codec supported on that DSP channel. Available values are: • CC_CAP_CODEC_G711U: 0x1 • CC_CAP_CODEC_G711A: 0x2 • CC_CAP_CODEC_G729IETF: 0x...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices VR-859 Cisco IOS Voice, Video, Fax Command Reference *********************************************************** ******summary of voice devices for all voice cards********* ******************************************************...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices VR-860 Cisco IOS Voice, Video, Fax Command Reference core type used Type of DSPware in use. Possible field values are: • 1 = UBL (boot loader) • 2 = high complexity core • 3 = medium complexity core • 4 = low complexity core • ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices VR-861 Cisco IOS Voice, Video, Fax Command Reference built-in codec bitmap Represents the bitmap of the codec built into the DSP firmware. Possible field values are: • CC_CAP_CODEC_G711U 0x0001 • CC_CAP_CODEC_G711A 0x0002 • CC_...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh shut VR-863 Cisco IOS Voice, Video, Fax Command Reference shut To shut down a set of digital signal processors (DSPs) on the Cisco 7200 series router, use the shut command in DSP configuration mode. To put DSPs back in service, use the no form o...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (dial-peer) VR-864 Cisco IOS Voice, Video, Fax Command Reference shutdown (dial-peer) To change the administrative state of the selected dial peer from up to down, use the shutdown command in dial-peer configuration mode. To change the ...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (DS1) VR-865 Cisco IOS Voice, Video, Fax Command Reference shutdown (DS1) To shut down a DS1 link (send a Blue Alarm), use the shutdown command in controller configuration mode. To activate the DS1 (cancel the sending of the Blue Alarm)...

Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (settlement) VR-869 Cisco IOS Voice, Video, Fax Command Reference response-timeout Configures the maximum time to wait for a response from a server. retry-delay Sets the time between attempts to connect with the settlement provider. ses...