Cisco VCO/4K - Manuals - manualsarea.com

Page 2 - Description; Front Panel Indicators and Ports Assignments; Total Current

4-2 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description Description The Storage I/O Module is two card slots wide and slides into the back of the VCO system where it plugsinto the control midplane. All outside connections are mounted on the faceplate of th...

Page 4 - Hard Disk Drive

4-4 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description The connectors mounted on the front pane are: : The connectors mounted on the board are: The LEDs mounted on the board are: Hard Disk Drive The hard disk drive is a SCSI-compatible drive that is used ...

Page 6 - Midplane Connectors

4-6 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description Figure 4-3 Location of Hard Disk Drive LED on the Combined Controller Midplane Connectors The Storage/Control I/O Module plugs into the midplane through standard DIN 41612 triple-row, 96-pinmale conne...

Page 7 - Serial Ports 1 and 2; Pin

4-7 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description Figure 4-4 Control Midplane Serial Ports 1 and 2 Serial Port 1/Console and Serial Port 2/TTY01 are dedicated ports for connecting the system masterconsole and remote maintenance modem, respectively. T...

Page 8 - Note; TxD

4-8 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description Master console and remote maintenance modem operating parameters (Baud Rate, Stop Bits, Bits perCharacter and Parity) are defined in the system database via the Peripheral Configuration screen. Wiring...

Page 9 - Serial Ports 3 and 4

4-9 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description Serial Ports 3 and 4 Serial Ports 3 and 4 are available for Serial I/O (SIO) links between the system and a host computer.These standard female DB-25 ports carry Asynchronous Data Link Control (ADLC) ...

Page 10 - Printer Interface; GND

4-10 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Description To implement Ethernet links, you must purchase the optional Ethernet Communications Packageavailable from Cisco Systems. This package contains supporting software and the Cisco VCO/4KEthernet Guide w...

Page 11 - SCSI Interface; Hardware Configuration; This section outlines hardware configuration options.; SCSI Termination Configuration; The SCSI Interface connector is reserved for future use.; Serial Port Configuration; Serial Ports 1 Through 4 and Jumper Settings

4-11 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Hardware Configuration Note You can use a 36-conductor, straight-through parallel cable to connect a printer to thesystem controller. However, only the conductors shown in Figure 4-7are used. For moreinformation...

Page 12 - Serial Ports 1 Through 4; Port; Hard disk drive

4-12 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Hardware Configuration You can position the jumpers in locations JP13 and JP18 (under the “To Terminal” etching) to configurethe CPU as a DCE termination. Moving the jumpers to these locations supports the follo...

Page 13 - Removal and Replacement Information; pins

4-13 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Removal and Replacement Information Figure 4-9 Jumper Configuration for DCE/DTE, Serial Ports 1-4 Serial port 4 can be configured to use clock signals by the TRXC4 and RTXC4 signal lines. Jumper JP15configuratio...

Page 15 - Removal Procedures; Caution; Grasp the card on its bottom edge as it is removed from the card rack.

4-15 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Removal and Replacement Information Removal Procedures Caution Follow ESD rules when removing a system component. Use a wrist strap for grounding. To remove a Storage/Control I/O Module in a nonredundant system,...

Page 16 - Replacement Procedures; Push the card inward until it makes contact with the midplane.; Troubleshooting; LEDs Not Illuminated

4-16 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Troubleshooting Replacement Procedures Caution Follow ESD rules when removing a system component. Use a wrist strap for grounding. To replace the Storage/Control I/O Module: Step 1 Place the replacement Storage/...

Page 17 - Troubleshooting Reference Materials

4-17 Cisco VCO/4K Mechanical Assemblies 78-10334-03 Chapter 4 Storage/Control I/O Module Troubleshooting Note The ENET PWR LED should be illuminated only when Ethernet is being used. If the ENETPWR LED is not illuminated and Ethernet is being used, contact Cisco Systems TechnicalSupport. Troubleshoo...