Cisco OL-12812-01 - Manuals

Cisco OL-12812-01 – Manual in PDF format online.

Manuals:

Manual

Manual Cisco OL-12812-01

Summary

Page 2 - This section describes the following modules:

Connecting Cisco Voice Network Modules to the Network 2- and 4-Channel Voice Network Modules 2 Connecting Cisco Voice Network Modules to the Network 2- and 4-Channel Voice Network Modules This section describes the following modules: • 1-slot 2-channel voice network module (NM-1V) (see Figure 1 ) • ...

Page 3 - Note; 0-Channel High-Density Voice Network Module; Figure 6

Connecting Cisco Voice Network Modules to the Network 60-Channel High-Density Voice Network Module 3 Connecting Cisco Voice Network Modules to the Network Note For the NM-HD-1V, NM-HD-2V, and NM-DS-2VE network modules, DSPs are on-board and are not field-replaceable units (FRUs). Note The NM-HD-1V, ...

Page 4 - Packet Voice DSP Modules; Figure 7

Connecting Cisco Voice Network Modules to the Network 60-Channel High-Density Voice Network Module 4 Connecting Cisco Voice Network Modules to the Network Figure 6 60-Channel High-Density Voice Network Module (NM-HDV) The 60-channel HDV network module converts voice and fax into IP packets or frames...

Page 5 - PVDM Orientation

Connecting Cisco Voice Network Modules to the Network 60-Channel High-Density Voice Network Module 5 Connecting Cisco Voice Network Modules to the Network Figure 7 PVDM Slot Locations PVDM Orientation PVDMs are manufactured with a polarization notch to ensure proper orientation and alignment holes t...

Page 6 - Removing PVDMs; Repeat; Installing PVDMs; Find the PVDM sockets on the HDV network module. (See; Top view

Connecting Cisco Voice Network Modules to the Network 60-Channel High-Density Voice Network Module 6 Connecting Cisco Voice Network Modules to the Network Removing PVDMs To remove PVDMs, follow these steps: Step 1 Find the PVDM sockets on the HDV network module. (See Figure 7 .) Caution Handle PVDMs...

Page 7 - ) by using the minimum amount of; Caution; Voice Network Module LEDs; View from front of board

Connecting Cisco Voice Network Modules to the Network Voice Network Module LEDs 7 Connecting Cisco Voice Network Modules to the Network Step 3 Beginning with bank 0, insert the PVDM into the connector slot at an angle, tilted toward the right side of the chassis. Align the PVDM in a vertical positio...

Page 8 - .) If the BANK LEDs do not come on after initial

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 8 Connecting Cisco Voice Network Modules to the Network Figure 11 Voice Network Module LED HDV Network Module LEDs High-density network modules have an enable (EN) LED, and five L...

Page 9 - Packet Fax or Voice DSP Modules; Module Name; -channel packet fax or voice DSP module

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 9 Connecting Cisco Voice Network Modules to the Network These three base-board SKUs also include a single VIC or VWIC slot for Foreign Exchange Station (FXS), Foreign Exchange Off...

Page 11 - Configuring E1 Ports for Normal or Wetting Current Mode; To configure an E1 port for normal mode, set the jumper to pins 2 and 3.; show controllers E1; command to look for line code violations and

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 11 Connecting Cisco Voice Network Modules to the Network • VIC-4FXS/DID (DID feature not supported) • VIC2-2FXO • VIC2-4FXO • VIC2-2FXS • VIC2-2E/M • VIC2-2BRI-NT/TE Configuring E...

Page 12 - Installing PVDM2 Modules

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 12 Connecting Cisco Voice Network Modules to the Network Figure 16 NM-HDV2-2T1/E1 Jumpers Configured for Normal Mode Installing PVDM2 Modules The NM-HDV2 network modules contain f...

Page 13 - shows the polarization notch and alignment holes on a

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 13 Connecting Cisco Voice Network Modules to the Network Figure 17 PVDM2 Module Slot Locations PVDM2 Module Orientation PVDM2 modules are manufactured with a polarization notch to...

Page 14 - To remove PVDM2 modules, follow these steps:; To install PVDM2 modules, follow these steps:

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 14 Connecting Cisco Voice Network Modules to the Network Removing PVDM2 Modules To remove PVDM2 modules, follow these steps: Step 1 Find the PVDM2 sockets on the NM-HDV2 network m...

Page 15 - up with the plastic guides on the socket.; NM-HDV2 Network Module LEDs

Connecting Cisco Voice Network Modules to the Network IP Communications High-Density Digital Voice or Fax Network Module 15 Connecting Cisco Voice Network Modules to the Network Step 2 Hold the PVDM2 module with the polarization notch on the right, near the back of the chassis, with the connector ed...

Page 16 - Related Documents; Related Topic; Cisco IOS Software

Connecting Cisco Voice Network Modules to the Network Related Documents 16 Connecting Cisco Voice Network Modules to the Network Figure 21 NM-HDV2 Network Module LEDs The NM-HDV2-1T1/E1 and NM-HDV2-2T1/E1 network modules have LEDs monitoring the alarm (AL), loopback (LP), and carrier detection (CD) ...

Page 17 - What’s New in Cisco Product Documentation

Connecting Cisco Voice Network Modules to the Network Obtaining Documentation, Obtaining Support, and Security Guidelines 17 Connecting Cisco Voice Network Modules to the Network Obtaining Documentation, Obtaining Support, and Security Guidelines For information on obtaining documentation, obtaining...