Cisco NOREGILMI - Manuals - manualsarea.com

Page 2 - Introduction; ILMI is also used for address registration.; Prerequisites; Requirements; There are no specific requirements for this document.; Components Used; Cisco − ILMI Address Registration Problems: %LANE−3−NOREGILMI

ILMI Address Registration Problems:%LANE−3−NOREGILMI Document ID: 10450 IntroductionPrerequisites Requirements Components Used ConventionsAssociated Error MessageConfigure Network Diagram ConfigurationsChecking ILMI ILMI Status When ILMI is Disabled on the Switch Interface Access List Configuration ...

Page 3 - Conventions; Associated Error Message; This error message can be reported by one of the following:; Configure; Network Diagram; This setup illustrates the problem:

Conventions For more information on document conventions, refer to the Cisco Technical Tips Conventions. Associated Error Message Address resolution problems are usually associated with the following error message: %LANE−3−NOREGILMI: [chars] [chars] cannot register [ATM address] with ILMI For exampl...

Page 4 - Configurations; Both Bernard and Tintin are configured with a LEC:; Tintin; Checking ILMI; ILMI Status; On a router, issue the show atm vc command.

Configurations Both Bernard and Tintin are configured with a LEC: Bernard interface ATM2/0/0 pvc 0/16 ilmi ! pvc 0/5 qsaal ! interface ATM2/0/0.1 multipoint description *** ILMI addr. registr. test *** lane client ethernet ilmi−test Tintin interface ATM1/0 atm pvc 1 0 5 qsaal atm pvc 2 0 16 ilmi ! i...

Page 5 - When ILMI is Disabled on the Switch Interface

bernard# show atm ilmi−status Interface : ATM2/0/0 Interface Type : Private UNI (User−side) ILMI VCC : (0, 16) ILMI Keepalive : Disabled ILMI State: UpAndNormal Peer IP Addr: 10.200.10.12 Peer IF Name: ATM0/0/0 Peer MaxVPIbits: 8 Peer MaxVCIbits: 14 Active Prefix(s) : 47.0091.8100.0000.0060.3e5a.450...

Page 6 - show atm vc traffic interface atm x/y/z 0 16

In this case, as ILMI has been disabled on the interface by issuing the no atm ilmi−enable command, theprefix is not sent to the router and hence, no address registration can occur. Access List Configuration Problems or ILMI Community Configured asRead−Only Access List configuration problems can occ...

Page 7 - Known Caveats; The switch already knows the NSAP address; If the Switch Knows the NSAP Address; When the NSAP Address Is Configured Statically on the Switch; On the router Bernard, you can see this message:

Casimir# show atm vc traffic interface atm 0/0/0 0 16 Interface VPI VCI Type rx−cell−cnts tx−cell−cnts ATM0/0/0 0 16 PVC 308 316 If you see only the sent or received counter incrementing, it may means that cells are being stuck on thebackplane causing ILMI to be stuck. Try issuing a shut/no shut com...

Page 8 - When the NSAP Address Is Registered via ILMI by Another Device; Bernard

R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4501/152 R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4502/152 R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4503/152 R I 1 ATM2/0/0 UP 0 47.0091.8100.0000.0060.3e5a.4501.0060.3e5a.4504/152 R I 1 ATM2/0...

Page 11 - Configuration Problems

lane config database test Tintin lane database test name ilmi−test server−atm−address 47.00918100000000603E5A4501.00603E5A4503.01 ! interface ATM2/0/0 no ip address no ip directed−broadcast logging event subif−link−status lane config fixed−config−atm−address lane config database test With this new c...

Page 12 - Related Information

The router does not receive its prefix and hence no address−registration can occur. When enabling debug atm ilmi atm 0/0/0 on the LightStream 1010, this can be seen when the atm 0/0/0interface is brought up: !−−− Output suppressed. Apr 2 12:42:11.792: ILMI: My Device type is set to Node (ATM0/0/0) A...