Page 2 - Prerequisites for Installing the Cisco WAE Network Modules; show version; Restrictions for Cisco WAE Network Modules
2 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Prerequisites for Installing the Cisco WAE Network Modules • Glossary, page 37 • Related Documentation, page 38 • Obtaining Documentation, Obtaining Support, and Security Guidelines, page 39 Prerequisi...
Page 3 - Cisco WAE Network Module Hardware Description; Faceplate and LEDs; Model
3 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Cisco WAE Network Module Hardware Description Because the network module does not have an external console port, you must configure the network module by initiating a Telnet session or by initiating a ...
Page 5 - Hardware Interfaces; Setting Up Cisco WAE Network Modules and Opening a Session
5 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Setting Up Cisco WAE Network Modules and Opening a Session Hardware Interfaces The host router and network module use several interfaces for internal and external communication (see Figure 2 ). Each in...
Page 6 - Setting Up Network Module Interfaces; Summary Steps
6 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Setting Up Cisco WAE Network Modules and Opening a Session If you lose power or connection during any of the following procedures, the software usually detects the interruption and tries to recover. If...
Page 7 - Detailed Steps; Procedure
7 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Setting Up Cisco WAE Network Modules and Opening a Session Detailed Steps From the host router CLI, perform the following steps: Procedure Command Step 1 Enter privileged EXEC mode on the host router. ...
Page 8 - Examples; Opening and Closing a Network Module Session; enable
8 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Setting Up Cisco WAE Network Modules and Opening a Session Examples The following partial output from the show running-config command shows how the interfaces are configured: interface service-engine1/...
Page 9 - Network Module Interface; session clear; Enter; admin
9 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Setting Up Cisco WAE Network Modules and Opening a Session Use the following commands from the Network Module Interface 4. Log in to the network module. 5. Perform configuration or other procedures by ...
Page 10 - Where to go Next; Starting the Cisco WAE Network Module and Displaying Status; configure terminal
10 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Starting the Cisco WAE Network Module and Displaying Status Where to go Next See the “Starting the Cisco WAE Network Module and Displaying Status” section on page 10 for information about maintaining ...
Page 11 - Configuration Mode; reset; session
11 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Starting the Cisco WAE Network Module and Displaying Status Accessing the ACNS Software on the Network Module You can access the ACNS software that runs on the network module by first accessing one of...
Page 12 - Displaying Status and Diagnostic Output
12 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Starting the Cisco WAE Network Module and Displaying Status Displaying Status and Diagnostic Output To verify the status of an installation, upgrade, or downgrade, or to troubleshoot problems, use the...
Page 15 - Command Reference
15 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Command Reference Command Reference This section documents the module-specific IOS router commands that are used to configure the WAE network module from the router command-line interface (CLI). All o...
Page 20 - show diag; Command
20 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 service-module integrated-service-engine reset show diag Displays controller information for ISE network modules. show interfaces integrated-service-engine Displays basic interface configuration infor...
Page 22 - interface
22 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 service-module integrated-service-engine session The following example clears the session that had been used to configure the ISE in the network module in slot 2: Router# service-module integrated-ser...
Page 25 - statistics
25 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 service-module integrated-service-engine statistics service-module integrated-service-engine statistics To display reset and reload information for an integrated-service-engine (ISE) network module an...
Page 26 - status
26 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 service-module integrated-service-engine status service-module integrated-service-engine status To display configuration information related to software on the integrated-service-engine (ISE) side of ...
Page 28 - show controllers integrated-service-engine; show
28 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 show controllers integrated-service-engine show controllers integrated-service-engine To display controller information for integrated-service-engine (ISE) network modules, use the show controllers in...
Page 29 - Related Commands
29 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 show controllers integrated-service-engine Related Commands Command Description service-module external ipv6 address Configures an interface for ISE network modules and enters interface configuration ...
Page 30 - Syntax Description; Release; chassis
30 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 show diag show diag To display hardware and diagnostic information for a networking device, a line card, a processor, a jacket card, a chassis, or a network module, use the show diag command in privil...
Page 31 - subslot
31 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 show diag Usage Guidelines Use this command to determine the type of hardware installed in your router, and to show detailed hardware information and EEPROM version information. This command displays ...
Page 33 - show interfaces integrated-service-engine; show interfaces integrated-service-engine
33 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 show interfaces integrated-service-engine show interfaces integrated-service-engine To display basic interface configuration information for an integrated-service-engine (ISE) network module, use the ...
Page 34 - Field
34 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 show interfaces integrated-service-engine rxload Receive load on the interface as a fraction of 255 (255/255 is completely saturated), calculated as an exponential average over 5 minutes. Encapsulatio...
Page 37 - Glossary
37 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Glossary Related Commands Glossary deferred Indicates that the chip, while ready to transmit a frame, had to defer because the carrier was asserted. lost carrier Number of times that the carrier was l...
Page 38 - Related Documentation; Related Topic
38 Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments OL-13140-02 Related Documentation Related Documentation For additional information on the ACNS software, IOS software, and the network module hardware, see the following documentation: NTP Network Time Protocol. ...