Cisco Network Switch Cabling - Manuals

Page 3 - Table 1 shows how each port is used on the switch and control node.; Table 1

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 18 Table 1 shows how each port is used on the switch and control node. Table 1 Description of Panel and Main Board Notation Notation Description ISL-1 Used to create the first half of interswitch link (ISL) connection b...

Page 4 - Racking and cabling guidelines; Figure 2 Stacked Switch Cabling; What about connecting application nodes?; Info Central

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 19 Racking and cabling guidelines To cable your control nodes to the network switches according to Figure 1, follow these steps. Remember that this sample configuration uses four network switches, so use these instructi...

Page 6 - Configuring the switches; Connecting the switch to a terminal server; Catalyst 3750 Switch Hardware Installation Guide; Cassatt Active Response; from inventorying VMs during the

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 21 Configuring the switches After you have racked and cabled the control nodes and switches, you need to configure both Cisco switch stacks. If you are using another of the Cassatt recommended switches (see the Info Cen...

Page 7 - Erasing the nvram filesystem will remove all configuration; Setting switch options; on page 24 to continue; Restoring the factory default settings; on; Notes; Notes; Select Enter

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 22 4. Plug in the Cisco switches in a stack.5. Many boot-up and self-test messages will scroll on the console monitor. When the process is completed, use the following table to determine your next step: Restoring the fa...

Page 8 - show switch; configure terminal; switch 3 renumber 2; Displays the following output:

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 23 3. If the switch was used previously in a switch stack, and is now in a different switch stack, it may have a switch number other than 1 and 2. To determine if the switch number must be reset, display the switch conf...

Page 9 - key to get started. Skip the initial configuration, as follows:; exit; reload

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 24 Changing Switch Number 3 to Switch Number 2 New Switch Number will be effective after next reboot 6. Exit the configuration mode, as follows : 7. Halt and perform a cold restart, as follows: 00:08:23: %SYS-5-RELOAD: ...

Page 10 - Turn off all the interfaces on the second switch, as follows:

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 25 2. Enter the privileged mode, as follows: 3. Enter the configuration mode, as follows: Enter configuration commands, one per line. End with CNTL/Z. 4. Turn the messages off, as follows: 5. Turn off all interfaces on ...

Page 11 - enable secret system; vtp mode transparent; spanning-tree portfast bpduguard default

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 26 7. Set the host name of the switch stack, as follows: 8. Set the switch stack’s enable password, as follows: 9. Turn off the VLAN trunking protocol (VTP), as follows: sw01(config)# Setting device to VTP TRANSPARENT m...

Page 12 - Creating a port-channel interface Port-channel 1

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 27 11. Aggregate the two physical links between the two Cisco switches in the stack into a single logical link, as follows: Creating a port-channel interface Port-channel 1 12. Set the interface connection to the router...

Page 13 - for the link to

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 28 13. Set the remaining interfaces, which are identical, as follows. %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this inte...

Page 14 - insert message here; switchport mode access; no ip igmp snooping; Catalyst 3750 Switch Software; to configure the four interfaces on the; Displays the following output; set

C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 29 %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode 14. Disable IGMP snooping, as follows: 15. Turn off the HTTP server, as ...