Cisco IE301016S8PC - Manuals

9 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Managing the Switch After completing Express Setup and installing the switch in your network, you can use the CLI for further configuration. You can enter Cisco IOS commands and parameters through the...

Cisco IE 3010 Switch Getting Started Guide 10 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 3. Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. 4. Use the CLI to enter configuration commands. See the software configuration ...

11 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Note For IP-30 compliance: - Use the 16-14 AWG wire and appropriate terminals for the AC or high-voltage DC power supply - Use the 12-10 AWG wire and appropriate terminals for the low-voltage DC powe...

Cisco IE 3010 Switch Getting Started Guide 12 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 • Relative humidity around the switch does not exceed 95 percent (noncondensing). • Altitude at the installation site is not higher than 10,000 feet. • For 10/100 and 10/100/1000 fixed ports, cable l...

13 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 1.75 in. (4.4 cm) Statement 1076 Attaching the Brackets Use six Phillips flat-head screws to at...

Cisco IE 3010 Switch Getting Started Guide 14 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Rack-Mounting the Switch Use the four number-12 Phillips machine screws to attach the brackets to the rack. Use the black Phillips machine screw to attach the cable guide to the left or right bracket...

Cisco IE 3010 Switch Getting Started Guide 16 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Wiring the Power Source The switches have two power supply slots to support these power supply modules: • PWR-RGD-LOW-DC: low-voltage DC (24 to 60 VDC) • PWR-RGD-AC-DC: high-voltage AC (100 to 240 VA...

Cisco IE 3010 Switch Getting Started Guide 18 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Connecting to the Power Source Prepare the power cable. Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 War...

Cisco IE 3010 Switch Getting Started Guide 22 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Connecting the Switch Ports 10/100 or 10/100/1000 Ports The 10/100 ports on the Cisco IE-3010-16S-8PC support Power over Ethernet (PoE) and enhanced PoE (ePoE). See the switch software configuration ...

23 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide SFP-Module Ports For a list of supported modules, see the release notes on Cisco.com. For detailed instructions on installing, removing, and connecting to SFP modules, see the SFP module documentatio...

Cisco IE 3010 Switch Getting Started Guide 24 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Troubleshooting Express Setup If Express Setup does not run or if the Express Setup page does not appear in your browser: Did you verify that POST completed before you started Express Setup? If not, ...

25 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Resetting the Switch to the Default Settings Caution Resetting the switch deletes the configuration and restarts the switch. 1. Press and hold the Express Setup button for about 10 seconds. The switc...

Cisco IE 3010 Switch Getting Started Guide 26 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 For More Information Go to Cisco.com: • Cisco IE 3010 Switch Hardware Installation Guide • Regulatory Compliance and Safety Information for the Cisco IE 3010 Switch • Release Notes for the Cisco IE 3...