Cisco H.323 - Manuals

3-5 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI Cisco HSI Configuration Table 3-3 Static System Data Parameters Parameter Type Description HOST_PORT_NUMBER1 [0-65535] The first port number to be used by the Cisco HSI. The default value is 0. No...

3-7 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI Cisco HSI Configuration Changing Static System Data To change static system data, you must first determine if it is acceptable to stop currently active calls in 20 seconds. If it is acceptable to ...

3-8 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI Cisco HSI Configuration Dynamic System Data To modify the dynamic system data parameters in Table 3-4 , use the sys_config_dynamic MML name variable for the prov-add , prov-dlt , and prov-ed comma...

3-10 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI H.323 Stack Configuration H.323 Stack Configuration The parameter name is based on the ASN.1 paths; but, in some cases, the parameter name has been shortened for convenience. For example, “capabi...

3-11 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI H.323 Stack Configuration Nonprovisionable Data The parameters in Table 3-5 cannot be altered through MML commands. MML Provisionable Data H.323 System Parameters The parameters in Table 3-6 are ...

3-12 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI H.323 Stack Configuration Example prov-add:name=q931,maxCalls=2000 The Update Type column in Table 3-7 shows when the change to a parameter takes effect once a change is made: • Immediate means t...

3-18 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI H.323 Stack Configuration Codec Selection The Cisco HSI negotiates the media stream codec to establish a match between the PSTN MGCP media gateway (for example, the Cisco AS5xxx series or Cisco M...

3-22 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration Table 3-16 presents common H.245 parameters for enabling the G.729 codec. The following MML command example shows the command sequence used to provision the H.245 parame...

3-23 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration • Configuring G.726 on the Cisco HSI • Configuring G.729 Annex and G.729 Annex B Asymmetric Codec Treatment The Asymmetric Codec Treatment feature averts the potential f...

3-24 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration Refer to Cisco PGW and Cisco IOS documentation at www.cisco.com for further information on these commands. T.38 Fax The T.38 Fax feature enables the HSI to alter a call,...

3-25 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration Support for the H.225 INFORMATION message is enabled by default. A crafts person can disable H.255 INFORMATION message support through a new property called Information ...

3-26 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration Table 3-17 presents examples of configuration commands that may be required to implement a particular G.Clear configuration. Table 3-17 Configuring Clear Channel Clear C...

3-28 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration If a non-preferred G.726 data rate is selected over a higher-preference codec, the HSI will continue with the call using the non-preferred data rate. This is preferable ...

3-29 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration H245, caps.table[i].entryNo 7261, 7262, … Note Set this parameter to a unique integer value prov-add:name=h245, caps.table[5].entryNo=7261 prov-add:name=h245, caps.table...

3-31 Cisco H.323 Signaling Interface User Guide OL-4806-01 Rev. A14 Chapter 3 Provisioning the Cisco HSI HSI Feature Configuration Configuring G.729 Annex and G.729 Annex B Table 3-18 presents examples of configuration commands that may be required to implement a particular configuration of G.729 An...