Cisco CISCO7576 - Manuals

Cisco CISCO7576 – Manual in PDF format online.

Manuals:

Manual

Manual Cisco CISCO7576

Summary

Page 2 - Product Overview; Note

2 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Product Overview Caution Before replacing the card cage and backplane assembly, read the “Safety Guidelines” section on page 7. The specific procedures for removing and installing the card cage and ...

Page 5 - Installation Safety, ESD Precautions, and Tools Required

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 5 Installation Safety, ESD Precautions, and Tools Required Figure 4 shows the location of the Cisco 7576 dual arbiters and chassis interfaces on the rear of thebackplane. Figure 4 Location of the Cisc...

Page 6 - Safety Warnings

6 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Installation Safety, ESD Precautions, and Tools Required Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, mayharm you. A warning symbo...

Page 7 - Safety Guidelines; Keep tools and chassis components away from walk areas.

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 7 Safety Guidelines Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com ...

Page 8 - Never install telephone wiring during a lightning storm.; Warning; measurement should be between 1 and 10 megohms.; Tools Required; ESD-preventive wrist strap

8 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Installation Safety, ESD Precautions, and Tools Required In addition, use the guidelines that follow when working with any equipment that is connected totelephone wiring or other network cabling: • ...

Page 9 - Removing and Replacing Processor Modules; Removing Processor Modules; To remove processor modules, follow these steps:

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 9 Removing and Replacing Processor Modules Removing and Replacing Processor Modules Before you can replace the card cage and backplane assembly, you need to remove all processormodules installed in th...

Page 11 - Replacing Processor Modules; To replace processor modules, follow these steps:

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 11 Replacing Processor Modules Figure 6 Board Rack with Processor Modules Caution To prevent damage to the processor modules, do not stack them on top of each other. Replacing Processor Modules You ca...

Page 12 - proper flow of cooling air through the chassis.; Figure 7; Removing Power Supplies; To remove a power supply, follow these steps:

12 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Removing Power Supplies Caution Always install blank processor module fillers in empty processor slots to maintain the proper flow of cooling air through the chassis. Step 7 Use a screwdriver to ti...

Page 13 - Disconnect the power supply cables from the power supplies.; Figure 8

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 13 Removing Power Supplies Step 2 Disconnect the power supply cables from the power supplies. • For DC-input power supplies, refer to the configuration note 1200-Watt DC-InputPower Supply Replacement ...

Page 14 - Repeat Step 3 and Step 4 for the power supply blank, if one is present.; Removing the Old Card Cage and Backplane Assembly; Timesaver

14 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Removing the Old Card Cage and Backplane Assembly Caution To maintain agency compliance requirements and meet electromagnetic interference (EMI) emissions standards in a Cisco 7513 or Cisco 7576 ch...

Page 15 - To remove the card cage and backplane assembly, follow these steps:; Caution

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 15 Removing the Old Card Cage and Backplane Assembly To remove the card cage and backplane assembly, follow these steps: Step 1 Turn the power switch on each power supply to the off position (O). Step...

Page 16 - Exchanging the EEPROM Devices

16 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Exchanging the EEPROM Devices Figure 11 Removing the Card Cage and Backplane Assembly Step 6 With the captive screws loosened, carefully pull the card cage and backplane assemblystraight out of the...

Page 17 - The new EEPROM device(s) that shipped on your new card cage are blank.

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 17 Exchanging the EEPROM Devices Caution The new EEPROM device(s) that shipped on your new card cage are blank. Note Do not perform these steps if you are upgrading a Cisco 7513 to a Cisco 7576. These...

Page 18 - Installing the New Card Cage and Backplane Assembly

18 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Installing the New Card Cage and Backplane Assembly Figure 13 Location of the EEPROM Devices on the Rear of the Card Cage (Cisco 7576) Note The Cisco 7576 features two routers on one backplane. The...

Page 20 - Replacing Power Supplies; To replace the power supply, follow these steps:

20 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Replacing Power Supplies Replacing Power Supplies To replace the power supply, follow these steps: Step 1 To replace a power supply, hold it as shown in Figure 15 and slide it into the power supply...

Page 21 - supply, reconnect the power cable at the power source.; Checking the System; Check the following components to make sure they are secure:

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 21 Checking the System Step 4 Repeat Step 1 through Step 3 for the second power supply if one is installed, or Step 1and Step 2 for the power supply blank if one is present. Note After the AC power ca...

Page 22 - Following is an example of this display:; model and Cisco IOS software release being used.

22 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Checking the System Following is an example of this display: (display text omitted) GS Software (RSP-K), Version 10.3(571) Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Wed 10-May-95 25:1...

Page 23 - Port and Slot Configuration Worksheet; Table 1; Location

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 23 Port and Slot Configuration Worksheet Port and Slot Configuration Worksheet The port and slot configuration worksheet (Table 1) is used with Figure 17 to assist in planning anddocumenting your use ...

Page 24 - Cisco 7576 Slot Assignments; Router A; — Interface processors are placed in slots 0 through 5; Router B; — Interface processors are placed in slots 8 through 12

24 Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions Port and Slot Configuration Worksheet Figure 17 Slot Numbering (Use with Table 1) Cisco 7513 and Cisco 7513-MX Slot Assignments The dual CyBus backplane has 13 slots: interface processors are place...

Page 25 - Cisco Connection Online; You can access CCO in the following ways:

Cisco 7513, Cisco 7513-MX, and Cisco 7576 Card Cage and Backplane Assembly Replacement Instructions 25 Cisco Connection Online Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary, real-time support channel. Maintenancecustomers and partners can self-register on CCO to obt...