Cisco ASR1002 - Manuals

5 Attach the Rack-Mount Brackets—Chassis Rear-Mounted To install the rack-mount on a Cisco ASR 1002 Router for a rear rack-mount configuration, follow these steps: Step 1 Locate the threaded ear holes in the rear sides of the chassis. Step 2 Position the rear rack-mount bracket top hole with the cha...

7 Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the rack-mount bracket ear holes specified in Step 9. Step 8 Hold the chassis in position against the mounting rails and follow these steps: a. Insert the bottom screw into the s...

8 Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and component damage. Step 1 Position the chassis so the front is closest to you and lift it carefully into the rack. To prevent injury, avoid any sudden twists or moves. Step ...

9 Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1002 Router Step 3 Using the bottom rack-mount ear hole, insert the screw through cable-management bracket and into the chassis rack-mount bracket. Figure 5 shows the cable-management brackets attached to the chassis. Step 4 Using a ...

11 Step 5 Locate the chassis ground connector on the side of your chassis. Step 6 Insert the two screws through the holes in the grounding lug. Step 7 Use the Number 2 Phillips screwdriver to carefully tighten the screws until the grounding lug is held firmly to the chassis. Do not overtighten the s...

12 Figure 8 Cisco ASR 1002 Integrated Route Processor Console and Auxiliary Port Connectors Step 3 After you establish normal router operation, you can disconnect the terminal. Note For console and auxiliary port pinouts, see Cisco ASR 1002 router specifications in the Cisco ASR 1000 Series Aggregat...

14 Proceed to the “Start the System” section on page 14 to complete the installation. 5 Start the System Before you start the system, you must connect power to it. Connect AC Power to the Cisco ASR 1002 Router This section provides instructions for installing the AC power supply into the Cisco ASR 1...

15 Figure 11 AC Power Supply for the Cisco ASR 1002 Router Table 1 describes the AC power supply LEDs on the Cisco ASR 1002 Router. Table 1 Cisco ASR 1002 Router AC Power Supply LEDs Note To connect an AC power supply to the Cisco ASR 1002 Router, follow the steps in Installing the AC Power Supply, ...

17 Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. Typically, green or green/yellow is used for ground. Make certain the lead color coding you choose for the DC-input power supply matches lead color coding used at the DC power...

18 Step 9 Connect the ground, positive, and negative leads to the power source. Step 10 Turn the branch source breaker on. Step 11 Turn the power supply switch to the On (I) position. Step 12 Verify that the LEDs illuminate. This completes the procedure for connecting DC-input power. Verifying Power...

22 *Feb 13 13:01:28.701: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down *Feb 13 13:01:29.728: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Feb 13 13:01:14.738: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (...

23 Router> enable Step 3 At the password prompt, enter your system password. If an enable password has not been set on your system, this step may be skipped. The following example shows entry of the password called enablepass : Password: enablepass Step 4 When your enable password is accepted, th...

27 Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS se...

28 Save the Running Configuration to NVRAM To store the configuration or changes to your startup configuration in NVRAM, use the copy running-config startup-config command to save your configuration changes to the startup configuration so that the changes will not be lost if the software reloads or ...

29 Power Off the Cisco ASR 1002 Router This section explains how to shut down the Cisco ASR 1002 Router. It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reload operation ...

30 Step 2 Using the handles on both sides of the module, with two hands, gently insert the Cisco ESP5 or -ESP10 into the top chassis slot. Note Handle the Cisco ESP5 and ESP10 by the carrier edges only; never touch the printed circuit board components or connector pins. Step 3 Once the board is seat...

31 Step 9 Power on the router by turning the power switch to the on (I) position. Replace a Power Supply in the Cisco ASR 1002 Router This section provides instructions for removing and replacing the AC power supply and the DC power supply in a Cisco ASR 1002 Router. Before you begin, make certain t...

33 Note Using a tie wrap for the AC power cable is optional and not necessary. However, if you do attach the AC power cable to a power supply tab and then you remove the AC power cable for some reason, check for any damage to the cable after you cut the tie wrap off. If the power cord is damaged, re...

34 Step 7 Replace the DC power supply within five minutes or the system will shutdown. You have completed the procedure for removing a DC power supply from the Cisco ASR 1002 Router. Installing the DC Power Supply This section provides information about replacing a DC power supply in the Cisco ASR 1...