Cisco 9396TX - Manuals

C H A P T E R 1 Overview • Overview, page 1 Overview The Cisco Nexus 9396TX switch (N9K-C9396TX) is a 2-RU, fixed-port switch designed for Top-of-Rack(ToR), Middle-of-Rack (MoR), and End-of-Rack (EoR) deployment in data centers. This switch has 48 fixed1- and 10-GBASE-T downlink ports and up to 12 f...

C H A P T E R 2 Preparing the Site • Temperature Requirements, page 5 • Humidity Requirements, page 5 • Altitude Requirements, page 6 • Dust and Particulate Requirements, page 6 • Minimizing Electromagnetic and Radio Frequency Interference, page 6 • Shock and Vibration Requirements, page 7 • Groundi...

Altitude Requirements If you operate a switch at a high altitude (low pressure), the efficiency of forced and convection cooling isreduced and can result in electrical problems that are related to arcing and corona effects. This condition canalso cause sealed components with internal pressure, such ...

To predict and prevent strong EMI, you might need to consult experts in radio frequency interference(RFI). Note The wiring is unlikely to emit radio interference if you use twisted-pair cable with a good distribution ofgrounding conductors. If you exceed the recommended distances, use a high-quality...

• Two 930-W DC power supplies • One 650-W AC power supply and one 930-W DC power supply For power-supply redundancy, you must provide power to both power supplies. For grid redundancy, youmust provide power to both power supplies and each power supply must be connected to a different powersource. No...

Rack and Cabinet Requirements You can install the following types of racks or cabinets for your switch: • Standard perforated cabinets • Solid-walled cabinets with a roof fan tray (bottom to top cooling) • Standard open four-post Telco racks • Standard open two-post Telco racks To correctly install ...

Clearance Requirements You must provide the chassis with adequate clearance between the chassis and any other rack, device, orstructure so that you can properly install the chassis, route cables, provide airflow, and maintain the switch.For the clearances required for an installation of this chassis...

C H A P T E R 3 Installing the Chassis • Install a Rack, page 13 • Unpacking and Inspecting a New Switch, page 14 • Planning How to Position the Chassis in the Rack, page 15 • Installing the Chassis in a Two-Post Rack, page 15 • Installing the Chassis in a Four-Post Rack, page 19 • Grounding the Cha...

Unpacking and Inspecting a New Switch Before you install a new chassis, you need to unpack and inspect it to be sure that you have all the items thatyou ordered and verify that the switch was not damaged during shipment. If anything is damaged or missing,contact your customer representative immediat...

Planning How to Position the Chassis in the Rack The switch is designed so that you can have coolant air flow through the switch in one of the two followingdirections: • Enter the port side and exhaust out the power supply side (port-side intake airflow) • Enter the power supply side and exhaust out...

Installing the Chassis in a Four-Post Rack Before you install the chassis, be sure that the rack is fully secured to the data center floor. You must attach the bottom support rails to the rack and attach the mounting brackets to the chassis beforemounting the chassis in the rack. Attaching the Botto...

Statement 1006 — Chassis Warning for Rack-Mounting and Servicing To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautionsto ensure that the system remains stable. The following guidelines are provided to ensure your safety: Warning • This unit should...

Grounding the Chassis The switch is grounded when you connect the chassis and the power supplies to the earth ground in thefollowing ways: • You connect the chassis (at its grounding pad) to the data center ground. If the rack is fully-bonded andgrounded, you can ground the switch by connecting it t...

Step 3 Secure the grounding lug to the chassis grounding pad with two M4 screws (see Callouts 1 and 3 in the previous figure),and tighten the screws to 12 in-lb (1.36 N·m) of torque. Step 4 Prepare the other end of the grounding wire and connect it to an appropriate grounding point in your site to e...

C H A P T E R 4 Connecting the Switch to the Network • Setting Up the Management Interface, page 29 • Uplink Connections, page 29 • Downlink Connections, page 30 • Guidelines for Connecting Ports, page 30 • Maintaining Transceivers and Optical Cables, page 31 Setting Up the Management Interface The ...

By default, the uplink ports operate at 40 Gbps, but you can use the speed-group 10000 command to change the administrative speed to 10 Gbps. If you change the speed, you must also use a QSFP+-to-SFP+ adapterand a supported SFP+ transceiver in each of the converted SFP+ ports. All of the ports in a ...

• Inspect routinely for dust and damage. If you suspect damage, clean and then inspect fiber ends undera microscope to determine if damage has occurred. Statement 1051 — Laser Radiation Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beamsor view di...

C H A P T E R 5 Replacing Modules • Replacing the Uplink Module, page 33 • Replacing a Fan Module, page 34 • Replacing an AC Power Supply, page 36 • Replacing a DC Power Supply, page 39 Replacing the Uplink Module You must shut down the switch before replacing the M6PQ or M12PQ uplink module. The M1...

Step 8 Holding the replacement module by its two handles, position the module with the electrical components on its backsidefacing the open uplink-module slot. Step 9 Slide the module all the way into the chassis until its front side comes in contact with the chassis. For the last 0.2 inches(0.5 cm)...

Step 4 Place the removed module on an antistatic surface or in an antistatic bag. If possible, repack the module in its packingmaterials for safe shipping or storage. Step 5 Follow these steps to replace the missing fan module withing two minutes to avoid a shutdown. a) Remove the replacement fan mo...

Replacing a DC Power Supply You can replace an DC power supply during operations so long as there is another power supply installed andoperating during the replacement. The switch requires only one power supply for operations, so you can hotswap the redundant power supply during operations. If there...

• For power supply redundancy, use one or two power sources. • For grid redundancy, use two power sources. If the switch has two power supplies, you can replace one power supply while the other one provides powerto the switch. If you have only one power supply in the switch, install the replacement ...

A P P E N D I X A Rack Specifications • Overview of Racks, page 43 • General Requirements for Cabinets and Racks, page 43 • Requirements Specific to Standard Open Racks, page 44 • Requirements Specific to Perforated Cabinets, page 44 • Cable Management Guidelines, page 44 Overview of Racks You can i...

• Standard 19-inch (48.3 cm) (two- or four-post EIA cabinet or rack, with mounting rails that conform toEnglish universal hole spacing per section 1 of ANSI/EIA-310-D-1992). For more information, see Requirements Specific to Perforated Cabinets, on page 44 . • The minimum vertical rack space require...

A P P E N D I X B System Specifications • Environmental Specifications, page 45 • Switch Dimensions, page 45 • Switch and Module Weights and Quantities, page 46 • Transceiver and Cable Specifications, page 46 • Power Input Requirements, page 46 • Power Cord Specifications, page 47 Environmental Spec...

Switch and Module Weights and Quantities Quantity Weight perUnit Component 1 22.45 lb (10.2kg) Cisco Nexus 9396TX Chassis (N9K-C9396TX) 1 — Uplink Module – M6PQ – M12PQ 2.0 lb (0.9 kg) 3.12 lb (1.4 kg) 3 (2 foroperations and1 forredundancy) 1.14 lb (0.5 kg) Fan Modules – Port-side exhaust (blue stri...

Table 1: Switch Power Input Requirements Maximum PowerConsumption Typical PowerConsumption 712 W 427 W Cisco Nexus 9396TX Power Cord Specifications If you are using a DC power supply, we recommend using a 8 AWG insulated cable (10 AWG minimum)customer-supplied cable to wire each power supply to its ...

A P P E N D I X C LEDs • Switch Chassis LEDs, page 49 • Uplink Module LEDs, page 50 • Fan Module LEDs, page 50 • Power Supply LEDs, page 50 Switch Chassis LEDs The BCN, STS, and ENV LEDs are located on the left side of the front of the switch. The port LEDs areappear as triangles pointing up or down...

Uplink Module LEDs The Status (STS) LED is located on the left side of the uplink module. There is an ACT LED located beloweach two uplink ports. Next to each ACT LED are two triangular port LEDs that point to the top or bottomto identify their port as being the top or bottom port. Table 3: Uplink M...

A P P E N D I X D Accessory Kits • Accessory Kit Contents, page 53 Accessory Kit Contents The following table lists and illustrates the contents for the accessory kit (N9K-C9300-ACK). Quantity Description Illustration 1 DB-9F/RJ-45F PC terminal 1 kit Ground lug kit • Two-hole lug (1) • M4 x 8-mm Phi...

A P P E N D I X E Site Preparation and Maintenance Records • Site Preparation Checklist, page 55 • Contact and Site Information, page 57 • Chassis and Module Information, page 57 Site Preparation Checklist Planning the location and layout of your equipment rack or cabinet is essential for successful...

Verification Time and Date Planning Activity Distance limitations forsignaling Site wiring RFI levels Contact and Site Information Use the following worksheet to record contact and site information for the installation. Contact person Contact phone Contact e-mail Building/site name Data center locat...