Page 3 - C O N T E N T S; About This Guide; First-Time Configuration
iii Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 C O N T E N T S About This Guide vii Objectives vii Audience vii Organization vii Document Conventions viii Additional Information ix Related Documentation ix Obtaining Documentation ix World Wide Web ix Document...
Page 4 - Cisco IOS Software Basics; Configuring with the Command-Line Interface
Contents iv Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Using the Setup Command Facility 2-3 Configuring Global Parameters 2-3 Completing the Configuration 2-5 Where to Go Next 2-6 C H A P T E R 3 Cisco IOS Software Basics 3-1 Getting Help 3-1 Understanding Co...
Page 5 - Command Reference
Contents v Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Configuring QoS Attributes 4-13 Creating a Class Map 4-14 Creating a Policy Map 4-14 Assigning a QoS Boilerplate to an Interface 4-16 Configuring Redundancy 4-16 Redundant MWR 1900s 4-16 Stand-Alone MWR 19...
Page 7 - Objectives; Organization
vii Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 About This Guide This preface discusses the objectives, audience, organization, and conventions of this software configuration guide, and where to get the latest version of this guide. Objectives This guide expla...
Page 8 - Document Conventions
viii Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 About This Guide Document Conventions Document Conventions This publication uses the following conventions to convey instructions and information. Note Means reader take note . Notes contain helpful suggestions ...
Page 9 - Additional Information; Obtaining Documentation; World Wide Web
ix Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 About This Guide Additional Information Additional Information This configuration guide does not contain the following: • Network design guide • Application case studies • Troubleshooting guide • A comprehensive r...
Page 10 - Ordering Documentation; Obtaining Technical Assistance
x Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 About This Guide Obtaining Technical Assistance Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updat...
Page 11 - Technical Assistance Center; Contacting TAC by Using the Cisco TAC Website
xi Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 About This Guide Obtaining Technical Assistance Cisco.com Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytim...
Page 12 - Contacting TAC by Telephone
xii Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 About This Guide Obtaining Technical Assistance Contacting TAC by Telephone If you have a priority level 1(P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a d...
Page 13 - Benefits
C H A P T E R 1-1 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 1 Overview of the MWR 1900 The MWR 1900 Mobile Wireless Edge Router is a networking platform optimized for use in mobile wireless networks. It extends IP connectivity to the cell site and Base Trans...
Page 14 - Software Features; Cisco IOS Software
1-2 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 1 Overview of the MWR 1900 Software Features transitions of the router pair leverages HSRP to control the relays on the VWIC-2MFT-T1-DIR (or VWIC-2MFT-E1-DIR) in each router to ensure that the relays on t...
Page 15 - PPP Multiplexing/Demultiplexing
1-3 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 1 Overview of the MWR 1900 Software Features The following features are supported in the network processor: • MAC Classify • ICMP • FIB (CEF) • Load-balancing • MAC Rewrite • QoS Matching, including IP Ac...
Page 16 - Redundancy Support
1-4 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 1 Overview of the MWR 1900 Software Features Figure 1-2 RTP Header Compression RFCs 2508 and 2509 describe a method for compressing not only the RTP header, but also the associated UDP and IP headers. Usi...
Page 17 - HSRP; MIB Support
1-5 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 1 Overview of the MWR 1900 Software Features HSRP Cisco’s Hot Standby Router Protocol (HSRP) is used to control which router is active and which is standby. HSRP uses a priority scheme to determine which ...
Page 18 - Limitations and Restrictions
1-6 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 1 Overview of the MWR 1900 Limitations and Restrictions Limitations and Restrictions The MWR 1900 requires a special release of Cisco IOS software. Not all Cisco IOS software features can be used with thi...
Page 19 - Before You Begin; Understanding Boot Images; Understanding Interface Numbering
C H A P T E R 2-1 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 2 First-Time Configuration This chapter describes how to use the setup command facility to configure your router. The setup command facility prompts you to enter information needed to start a router...
Page 21 - Before Starting Your Router; Using the Setup Command Facility; Configuring Global Parameters
2-3 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 2 First-Time Configuration Using the Setup Command Facility Before Starting Your Router Before you power ON your router and begin to use the setup command facility, make sure you follow these steps: Step ...
Page 23 - Completing the Configuration
2-5 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 2 First-Time Configuration Completing the Configuration Step 6 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port: The virtu...
Page 24 - Where to Go Next
2-6 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 2 First-Time Configuration Where to Go Next media-type 100BaseX half-duplex no ip address ! interface FastEthernet0/1 shutdown no ip address ! end To complete your router configuration, do the following: ...
Page 25 - Getting Help
C H A P T E R 3-1 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 3 Cisco IOS Software Basics This chapter describes what you need to know about the Cisco IOS software before you configure the router using the command-line interface (CLI). This chapter includes th...
Page 26 - Understanding Command Modes
3-2 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 3 Cisco IOS Software Basics Understanding Command Modes Understanding Command Modes The Cisco IOS user interface is divided into different modes. Each command mode permits you to configure different compo...
Page 27 - Undoing a Command or Feature; Saving Configuration Changes
3-3 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 3 Cisco IOS Software Basics Undoing a Command or Feature Note You can press Ctrl-z in any mode to immediately return to enable mode ( Router# ), instead of entering exit , which returns you to the previou...
Page 30 - Verifying the Version of Cisco IOS Software; Configuring the Host Name and Password
4-2 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Before You Begin Before You Begin Before you configure the MWR 1900, there are a few caveats of which you should be aware: • You cannot disable Cisco Express ...
Page 31 - Configuring Loopback Interfaces
4-3 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Loopback Interfaces Step 3 Change the name of the router to a meaningful name. Router(config)# hostname router_name The prompt changes from “Route...
Page 32 - Configuring Fast Ethernet Interfaces; Configuring the FE Interface IP Address; Setting the Speed and Duplex Mode
4-4 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Fast Ethernet Interfaces Configuring Fast Ethernet Interfaces To configure the FE interface of the MWR 1900, complete the following tasks: • Confi...
Page 33 - Configuring Routing Protocol Attributes; Configuring PIM
4-5 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Fast Ethernet Interfaces To configure speed and duplex operation, do the following while still in interface configuration mode: Step 1 Specify the...
Page 34 - Configuring HSRP Support
4-6 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Fast Ethernet Interfaces Configuring HSRP Support In redundant configurations, the MWR 1900 uses HSRP to control the active and standby routers. T...
Page 35 - Enabling the FE Interface; Configuring Multilink Interfaces
4-7 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Multilink Interfaces Step 5 Specify other interfaces on the router for the HSRP process to monitor in order to alter the HSRP priority for a given...
Page 36 - Configuring Multilink PPP; Configuring IP Address Assignment
4-8 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Multilink Interfaces Configuring Multilink PPP As higher-speed services are deployed, Multilink-PPP (MLP) provides a standardized method for sprea...
Page 37 - Configuring PPP Multiplexing; Configuring RTP/UDP Compression
4-9 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Multilink Interfaces To configure IP address assignment, do the following do the following while still in multilink interface configuration mode: ...
Page 39 - Configuring T1 and E1 Interfaces; Configuring T1 Interfaces
4-11 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring T1 and E1 Interfaces Configuring T1 and E1 Interfaces To configure a T1/E1 multiflex trunk interface, enter the following Cisco IOS commands at t...
Page 40 - Configuring E1 Interfaces
4-12 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring T1 and E1 Interfaces Step 7 Configure the serial interface. Specify the T1 slot (always 0), port number, and channel group. Router(config)# inter...
Page 41 - Configuring QoS Attributes
4-13 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring QoS Attributes Step 5 Configure the cable length. Router(config-controller)# cablelength feet Note Although you can specify a cable length from 0...
Page 42 - Creating a Policy Map
4-14 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring QoS Attributes Creating a Class Map For each class map that you want to create, do the following in global configuration mode: Step 1 Assign a na...
Page 44 - Assigning a QoS Boilerplate to an Interface; Configuring Redundancy
4-16 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Configuring Redundancy Step 5 Repeat Step 2 and Step 3 for each class map. Step 6 Exit policy map configuration mode. Router(config-pmap-c)# exit Router(conf...
Page 46 - Verifying the Configuration
4-18 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Saving Configuration Changes Saving Configuration Changes To prevent the loss of the router configuration, save it to non-volatile random access memory (NVRA...
Page 50 - Notes; Monitoring and Managing the MWR 1900
4-22 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Monitoring and Managing the MWR 1900 network 192.168.146.0 0.0.0.255 area 51 network 192.168.147.0 0.0.0.255 area 51 network 10.0.0.0 0.255.255.255 area 51 d...
Page 51 - Show Commands for Monitoring the MWR 1900
4-23 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 4 Configuring with the Command-Line Interface Monitoring and Managing the MWR 1900 Step 6 Enter the following commands to specify the public and private SNMP community names: Router(config)# snmp-server ...
Page 54 - clear ip rtp header-compression
5-2 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 5 Command Reference clear ip rtp header-compression clear ip rtp header-compression To clear Real-Time Transport Protocol (RTP) header compression structures and statistics, use the clear ip rtp header-co...
Page 61 - ppp mux delay
5-9 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 5 Command Reference ppp mux delay ppp mux delay To set the maximum time the processor can wait before sending a superframe, use the ppp mux delay command in interface configuration mode. To set the maximu...
Page 62 - ppp mux frame
5-10 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 5 Command Reference ppp mux frame ppp mux frame To set the maximum length (in bytes) of the PPP superframes, use the ppp mux frame command in interface configuration mode. To set the maximum length to th...
Page 63 - ppp mux pid
5-11 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 5 Command Reference ppp mux pid ppp mux pid To set the default receiving PPP protocol ID, use the ppp mux pid command in interface configuration mode. To remove this configuration, use the no form of thi...
Page 64 - ppp mux subframe length
5-12 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 5 Command Reference ppp mux subframe length ppp mux subframe length To set the maximum length (in bytes) of the PPP subframes, use the ppp mux subframe length command in interface configuration mode. To ...
Page 65 - ppp mux subframe count
5-13 Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide 78-13983-04 Chapter 5 Command Reference ppp mux subframe count ppp mux subframe count To set the maximum number of PPP subframes that can be contained in a superframe, use the ppp mux subframe count command in interface con...