Cisco 7100 Series - Manuals

Page 3 - Prepare for Installation; Warning; — Lift the router safely out of the packing container.; Verify that you have the required tools and parts:; — Four screws for installing the router in the rack (not included).

1 Prepare for Installation Note: For detailed hardware installation instructions and safety guidelines, refer to theCisco 7100 Series VPN Router Installation and Configuration Guide. Warning Only trained and qualified personnel should install, replace, or service this equipment. Warning Read the Ins...

Page 5 - Rack-Mount the Router; Locate the brackets and screws.; — Front panel forward

3 Rack-Mount the Router 22061 Cisco 7100 SERIES 22062 0 2 Attach the Brackets to theRouter 1 Locate the brackets and screws. 2 Use a Phillips screwdriver to attach thebrackets on the side panels of the routerin one of the following ways: — Front panel forward — Rear panel forward Note: Although thes...

Page 6 - Attach the Router to the Rack; Do not touch the power

4 . Rack-Mount the Router (continued) 22064 Note: The second bracket attaches to the other side of the chassis. The brackets can also be installed with the front panel forward. 0 2 Attach the Router to the Rack 1 Locate the screws to mount the chassisin the rack. 2 Position one person to lift the ch...

Page 7 - Attach the Grounding Lug; Locate the grounding lug and screws.

5 Rack-Mount the Router (continued) 22065 0 2 Chassis grounding receptaces Grounding wire Grounding lug Screws Attach the Grounding Lug Note: Before you connect power or poweron your router, we strongly recommend thatyou attach the grounding lug to the chassisgrounding receptacles. 1 Locate the grou...

Page 8 - Connect the Router to the Network

6 Connect the Router to the Network AC O K D C O K OT F AC O K D C O K OT F R X T X E 3 R X 5 T X E 3 R X E N C E L C A R A L M I C O N S F E 0 / 0 F E AC T 0 / 1 AU X 0 2 7 1 4 0 - 2 A E 3 100-240Vac 50/60Hz 5-2.5A 525W R X E N C E L C A R A L M AC T L N K 0 L N K 1 P W R S Y SR DY S L OT 0 S L OT ...

Page 10 - Connect the T3 Ports

8 Connect the Router to the Network(continued) 5 I X M T R R C V R X M T R R C V R E N R C L K F E R F R L A I S O O F L L R C L K F E R F R L A I S O O F L L 22072 To T3 network equipment Serial 1/0 Serial 2/0 Connect the T3 Ports The T3 port supports full-duplex operationat T3 (45-Mbps) speeds. Us...

Page 11 - Connect the E3 Ports

9 Connect the Router to the Network(continued) 5 I X M T R R C V R E N R C L K F E R F R L A I S O O F L L 22073 To E3 network equipment Ferrite bead Serial 1/0 Connect the E3 Ports The E3 port supports full-duplex operationat E3 (34-Mbps) speeds. Use a 75-ohmcoaxial cable to connect to an E3 serial...

Page 13 - Class 1 laser product.; Because invisible laser

11 Connect the Router to the Network(continued) 5 I 1 5 5 - M M R X R X E N C E L C A R A L M T X 22129 To ATM network equipment ATM 1/0 Connect the ATM SMI3 andMM3 Ports The SMI3 (OC-3c/STM-1 single-modeintermediate reach) and MM3(OC-3c/STM-1 multimode) ports providean interface to ATM networks and...

Page 14 - Connect the Console Port; Attach the other end of the cable to a terminal or PC.

12 Connect the Router to the Network(continued) Connect the Console Port Use the console terminal for local administrative access to the router. 1 Attach the appropriate cable (RJ-45 rollover cable and an RJ-45-to-DB-25 orRJ-45-to-DB-9 adapter) directly to the receptacle on the router. The adapters ...

Page 15 - Connect the Power; Never defeat the ground; The AC power supply

13 Connect the Power 5 I AC T AC T L N K 1 P W R S L OT 0 S L OT 1 C O N S F E 0 / 0 F E 0 / 1 AU X 0 2 P W R S Y SR DY X M T R R C V R E N R C L K F E R F R L A I S O O F L L 7 1 2 0 - T 3 22131 Connect the Cisco 7120Series AC Power Supply The power supply is a four-output switchingpower supply wit...

Page 16 - Connect the Cisco 7140 Series Dual AC Power Supply; Plug the AC power supply cable into the AC power source.

14 Connect the Power (continued) Connect the Cisco 7140 Series Dual AC Power Supply The power supply is a four-output switching power supply with power factor correction andregulated outputs. Note: For additional AC power cable strain relief, secure the cable to the power supply handleby inserting a...

Page 17 - Check Conditions Prior to System Startup; Check the following conditions before you start your router:; Start the System; Listen for the fans you should immediately hear them operating.

15 Start the System Check Conditions Prior to System Startup Check the following conditions before you start your router: • Any port adapter or service module is securely inserted in its slot. • All network interface cables are connected. • A Flash Disk or Flash memory card is installed in its PC Ca...

Page 18 - Use the Setup Facility

16 Start the System (continued) Use the Setup Facility This section provides a sample of a basic router configuration using the setup facility. Theoutput from the setup facility varies depending on the Cisco 7100 series model you areinstalling. It does not contain a complete example of all possible ...

Page 19 - Enter yes or press Return to see the current interface summary:

17 Start the System (continued) Last reset from power-on X.25 software, Version 3.0.0. 2 FastEthernet/IEEE 802.3 interface(s) 2 ATM network interface(s) 125K bytes of non-volatile configuration memory. 8192K bytes of Flash PCMCIA card at slot 1 (Sector size 128K). 8192K bytes of Flash internal SIMM ...

Page 22 - Review your configuration.

20 Start the System (continued) 10 Review your configuration. The following configuration command script was created: hostname sanjose enable secret 5 $1$gG.I$gc9JUfK2r6pIDL0vo3j191 enable password betty line vty 0 4 password fred no snmp-server ! ip routing no clns routing ! interface FastEthernet0...

Page 23 - Save your settings to NVRAM by selecting option 2.; For More Information

21 11 Save your settings to NVRAM by selecting option 2. [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 Your router is now minimally configured and ready ...