Cisco 6807-XL - Manuals

C H A P T E R 1 Product Overview • Switch Models, page 1 • Front Panel, page 1 • Rear Panel, page 11 Switch Models Table 1: Switch Models Description Switch Model Has a seven-slot modular chassis. The switch supports redundant power supply modules (AC input),redundant supervisor engines, fan tray, p...

• System ground connector Figure 1: Cisco Catalyst 6807-XL Front Panel Power entry modules (PEMs), labeled AC1through AC4 6 Fan tray 1 Power supply modules (PSMs), labeled 1through 4 7 Module slots (line cards) 1, 2, 5,6, and 7 2 Power supply converter (PSC), labeled PSC1and PSC2 8 Supervisor engine...

Finding Serial Numbers, on page 106 Supervisor Engine The switch supports these Supervisor Engine 2T models: • VS-S2T-10G • VS-S2T-10G-XL The term supervisor engine is used to refer to Supervisor Engine 2T. Note The following requirements apply to the supervisor engines installed on the switch: • In...

• WS-X6848-SFP-2T and WS-X6848-SFP-2TXL • WS-X6716-10T • WS-X6816-10T-2T and WS-X6816-10T-2TXL • WS-X6716-10G • WS-X6816-10G-2T and WS-X6816-10G-2TXL • WS-X6724-SFP • WS-X6824-SFP-2T and WS-X6824-SFP-2TXL • WS-X6904-40G-2T and WS-X6904-40G-2TXL The switch supports the following Cisco Catalyst 6500 S...

Individual fans are not field-replaceable units (FRUs). You must replace the fan tray. Note Related Topics Removing and Installing the Fan Tray, on page 54 Troubleshooting the Fan Tray, on page 105 Fan Tray LED, on page 8 Power Supply Module The switch supports one to four field-replaceable power su...

The PSMs provide 3000 W when powered with 240 VAC, and 1300 W when powered with 120 VAC. Insystems where power supply modules provide different wattage, you may not have true redundancy. If thePSM with the higher wattage fails, the PSM with the lower wattage might not be able to handle the entireloa...

• Redundancy — The PSCs share power when both are installed. If one PSC fails, the chassis will still be operational. Related Topics Removing and Installing the Power Supply Converter, on page 57 Power Supply Converter LEDs, on page 10 LEDs Use the switch LEDs to monitor switch activity and performa...

Meaning LED Color One or more individual fans have failed Red Related Topics Removing and Installing the Fan Tray, on page 54 Troubleshooting the Fan Tray, on page 105 Fan Tray, on page 4 Air Flow, on page 15 Power Supply Module LEDs The PSM includes an IN, OUT, and FAULT LED, as shown in the follow...

Meaning LED Color LED Power supply module has malfunctioned Red FAULT 4 The system On/ Off switch turns the power supply output on and off. Related Topics Removing and Installing Power Supplies, on page 50 Troubleshooting the Power Supply Module, on page 104 Power Supply Module, on page 5 Power Entr...

Related Topics Removing and Installing the Power Supply Converter, on page 57 Power Supply Converter, on page 7 Rear Panel These rear panel components are located behind the back plate of the chassis: • Backplane • Clock module • Voltage Termination-Enhanced (VTT-E) module Figure 5: Cisco Catalyst 6...

• Four channels — Each module slot has four channels connected to each supervisor-engine slot (A total of eight). • The following clock frequencies: ◦ 3.13 GHz: For up to 20 Gbps (per channel) ◦ 6.25 GHz: For up to 40 Gbps (per channel) ◦ 7.50 GHz: For up to 55 Gbps (per channel) ◦ 15.0 GHz: For up ...

C H A P T E R 2 Preparing for Installation • Safety Warnings, page 13 • Site Requirements, page 14 • Power Requirements, page 23 • Cabling Requirements, page 24 • Rack-Mounting Guidelines, page 24 • Site Preparation Checklist, page 25 Safety Warnings Safety warnings appear throughout this publicatio...

Site Requirements Planning a proper location for the switch and layout of the equipment rack or wiring closet is essential forsuccessful system operation. These sections describe some of the basic site requirements that you should beaware of as you prepare to install your switch, including the follo...

Air Flow The switch is designed to be installed in an environment where there is a sufficient volume of air available tocool the supervisor engines, modules, and power supplies. If there are any constraints with regard to the freeflow of air through the chassis, or if the ambient air temperature is ...

Related Topics Removing and Installing the Fan Tray, on page 54 Troubleshooting the Fan Tray, on page 105 Fan Tray LED, on page 8 Selecting Rack Enclosure Cabinets Cisco Systems has identified the following rack-enclosures that are determined to be Cisco-compatible: Panduit Corporation The following...

Table 7: Air Flow Specifications and Fan Tray Support Air Volume Air Filter Available Airflow Exhaust Airflow Intake Fan Tray Model Number 850 CFM No Left side Right side C6807-XL-FAN Figure 6: Air Flow Direction Module air exhaust 3 Module air inlet 1 Power supply air exhaust 4 Power supply air inl...

Altitude Operating a system at high altitude (low pressure) reduces the efficiency of forced and convection coolingand may result in electrical problems related to arcing and corona effects. This condition may also cause sealedcomponents with internal pressure, such as electrolytic capacitors, to fa...

• Always use shielded cables with metal connector shells for attaching peripherals to the system. When wires are run for any significant distance in an electromagnetic field, interference can occur betweenthe field and the signals on the wires. This fact has two implications for the construction of ...

Besides these appliances, the greatest threats to a system's power supply are surges or blackouts that are causedby electrical storms. Whenever possible, turn off the system and peripherals, if any, and unplug them fromtheir power sources during thunderstorms. If a blackout occurs — even a temporary...

Maintaining Safety with Electricity When working on electrical equipment, follow these guidelines: • Do not work alone if potentially hazardous conditions exist anywhere in your work space. • Never assume that power is disconnected from a circuit; always check the circuit before working on it. • Loo...

Preventing Electrostatic Discharge Damage Electrostatic discharge (ESD) damage may occur when modules or other FRUs are improperly handled, andresult in intermittent or complete failure of the modules or FRUs. Modules consist of printed circuit boardsthat are fixed in metal carriers. EMI shielding a...

• The AC power receptacles used to plug in the chassis must be the grounding type. The groundingconductors that connect to the receptacles should connect to protective earth ground at the serviceequipment level. Cabling Requirements When running power and data cables together in overhead cable trays...

You can also use a center rack-mount kit for 23-inch, telco-style racks. The kit is not included in the accessorykit, but can be ordered separately (Part number C6800-XL-CNTR-MNT=). Installation instructions are includedwith the kit. If the rack is on wheels, ensure that the brakes are engaged and t...

C H A P T E R 3 Installing the Switch • Installation Tasks , page 29 • Accessory Kit, page 31 • Unpacking the Switch, page 32 • L Brackets on the Chassis, page 33 • Installing the Rack-Mount Shelf Kit, page 33 • Rack-Mounting the Chassis, page 37 • Establishing System Ground, page 41 • Attaching an ...

To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using thehandles on modules (such as power supplies, fans, or cards); these types of handles are not designed tosupport the weight of the unit. Statement 1032 Warning Hazardous voltage or energy is present...

rack-mount screws. The clip nuts or cage nuts are not included as part of the accessory kit; you mustobtain them on your own. • Rack-mount shelf kit — This kit is used to support the weight of the chassis while you secure the chassis L brackets to the rack enclosure. It consists of two shelf bracket...

L Brackets on the Chassis The switch chassis is shipped with two L brackets installed on the front sides of the chassis. The L bracketsare secured to the chassis with ten M3 Phillips-head screws (five on each side). Figure 7: L Brackets on the Chassis Handhold 3 Right L bracket. 1 Left L bracket. 2 ...

Table 12: Rack-Mount Kit Contents and Description Description Quantity Part Is attached to the rack posts to form a shelf for the switchchassis to rest on. 2 Shelf bracket Is attached between the two side rack-mount brackets tosecure them together. 1 Cross Bar bracket Secures the brackets to a rack ...

Procedure Step 1 Position the support flange of the left shelf bracket on the rear of the left rail. Align and secure the bracket tothe rack by using five EA screws. Step 2 Position the support flange of the right shelf bracket on the rear of the right rail (make sure that it is level withthe left s...

Figure 9: Installing Shelf and Crossbar Brackets in a 17.75-inch Opening Two EA screws on each side, to secure theshelf bracket to the rack 5 Left rail 1 Crossbar bracket 6 Left shelf bracket 2 One M3 screw on each side to secure thecrossbar bracket to the shelf 7 Right rail 3 Right shelf bracket 4 ...

Step 4 (Optional) To install one or both of the optional cable guide assemblies, position the cable guides such thatthe cable guide mounting holes are aligned with the L bracket holes and the rack rail holes, as shown in thefollowing figure: Figure 11: Installing the Cable Guide in a Rack with a 17....

1 Connecting the chassis to system ground. 2 Installing and connecting the power supplies to the power source. 3 Connecting the network interface cables to the supervisor engine and modules. This may involve installingtransceivers before you attach the network interface cables. 4 Powering up the cha...

Right-angled grounding lug 3 Step 5 Prepare the other end of the grounding wire, and connect it to an appropriate grounding point in your site toensure adequate earth ground for the switch. Related Topics Preventing Electrostatic Discharge Damage , on page 23 Attaching an ESD Strap After you install...

• Handle carriers using the available handles or edges only; avoid touching the printed circuit boards orconnectors. • Place a removed component boardside up on an antistatic surface or in a static shielding container. Ifyou plan to return the component to the factory, immediately place it in a stat...

Online Diagnostics The Cisco Catalyst 6807-XL switches running Cisco IOS have many levels of online diagnostic capabilities.The online diagnostics are divided into the following categories: • Bootup — Bootup diagnostics automatically run during bootup, module OIR, or switchover to a backup superviso...

• No parity • 2 stop bits Step 3 Connect to the port using the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-25 DCE adapter (labeledModem).The console port mode switch should be in the IN position (factory default). Step 4 Position the cable in the cable guide (if installed). Make sure there are...

C H A P T E R 4 Removing and Replacing FRUs Only trained and qualified personnel should be allowed to install, replace, or service this equipment.Statement 1030 Warning • Online Insertion and Removal , page 49 • Removing and Installing Power Supplies, page 50 • Removing and Installing the Fan Tray, ...

supervisor engine, the Layer 2 addresses of all the ports change to those specified in the address allocator onthe new supervisor engine. Removing and Installing Power Supplies This section describes how to remove and install PSMs. Note • The PSMs installed in the switch chassis should be AC input o...

Removing AC Power Supplies Each power supply module has a power hold-up time of 20 milliseconds at 100 percent load and fully supportsOIR. To remove an AC-input power supply, follow these steps: Hazardous voltage or energy is present on the backplane when the system is operating. Use caution whenser...

Step 2 Grasp the power supply latch and pull to slide the power supply part of the way out of the chassis. Place yourother hand underneath the power supply, and slide the power supply clear out of the chassis. Step 3 If the power supply bay is to remain empty: a) Install a blank (Cisco part number C...

Checking Fan Tray Installation To verify that the new fan assembly is installed correctly, perform these steps: Procedure Step 1 If the switch is powered on, listen for the fans; you should immediately hear them operating. If you do nothear them, ensure that the fan module is inserted completely and...

The fans might still be turning when you remove the fan assembly from the chassis. Keep fingers,screwdrivers, and other objects away from the openings in the fan assembly ’ s housing. Statement 263 Warning Removing and Installing the Power Supply Converter This section describes how to remove and in...

If the system is powered on and PSC is installed properly, the PSC STATUS LED is green. Figure 18: Installing the PSC Mounting screws (one for each PSC) 2 Power rail connectors 1 Removing the Power Supply Converter To remove the PSC, perform these steps: Before You Begin • Ensure that the system (ea...

A P P E N D I X A Technical Specifications • Physical Specifications, page 61 • Environmental Specifications, page 62 Physical Specifications The following are the physical characteristics of the chassis: Table 13: Physical Characteristics of the Cisco Catalyst 6807-XL Switch Chassis Details Physica...

Related Topics Rack-Mounting the Chassis, on page 37 Chassis, on page 2 Environmental Specifications The following are the environmental specifications of the chassis: Table 14: Environmental Specifications of the Cisco Catalyst 6807-XL Switch Chassis Environmental Specification Item Certified for o...

A P P E N D I X B Power Supply Specifications • 3000 W AC-Input Power Supply Specifications, page 65 • 3000 W Power Supply AC Power Cords, page 67 • Chassis and Module Power and Heat Values, page 74 3000 W AC-Input Power Supply Specifications The following table lists specifications for the 3000 W A...

8 The kVA rating listed for the power supply should be used as the sizing criteria for both UPS outputs as well as standard circuits and transformers to power a switch 3000 W Power Supply AC Power Cords The following table lists the specifications for the AC power cords that are available for the 30...

Figure 34: CAB-ACS-16= (Switzerland) Related Topics Removing and Installing Power Supplies, on page 50 Troubleshooting the Power Supply Module, on page 104 Power Supply Module, on page 5 Power Entry Module, on page 7 Chassis and Module Power and Heat Values The following tables provide the power and...

A P P E N D I X C Transceivers, Module Connectors, and CableSpecifications • Pluggable Transceivers, page 79 • Module Connectors, page 84 • Cable Specifications, page 88 Pluggable Transceivers This section provides brief descriptions of the pluggable transceivers that can be installed in the switch ...

To determine if a specific 40-GB transceiver is compatible with the supported modules, see the Cisco 40-Gigabit Ethernet Transceiver Modules Compatibility Matrix document that is available on Cisco.com. Note WDM Transceivers The following table lists the supported modules, applicable illustrations, ...

More Information Supported on TheseModules Description WDMTransceiverType Cisco 10GBASE DWDM X2Modules • WS-X6816-10G • WS-X6816-10G XL • WS-X6908-10 • WS-X6908-10 XL • VS-S2T-10G • VS-S2T-10G XL The Cisco DWDM X2transceiver is a hot-swappableI/O module that you can pluginto an Ethernet X2 port of t...

Category 5e, Category 6, and Category 6a cables can store large levels of static electricity because of thedielectric properties of the materials used in their construction. Always ground the cables (especially innew cable runs) to a suitable and safe earth ground before connecting them to the modul...

LC Connector The LC fiber optic connector is a small form-factor fiber-optic connector that provides high-density fiberconnectivity. The LC connector can be used with either MMF cable or SMF cable. The LC connector uses alatching clip mechanism that is similar to the one used on the RJ-45 copper con...

Dust cap 6 Housing assembly 3 Cleaning the Fiber-Optic Connectors Fiber-optic connectors are used to connect two fibers together. When these connectors are used in acommunications system, proper connection becomes a critical factor. Fiber-optic cable connectors can be damaged by improper cleaning an...

How to Clean the Fiber-Optic Connectors Use extreme care when removing or installing connectors so that you do not damage the connector housingor scratch the end-face surface of the fiber. Always install protective covers on unused or disconnectedcomponents to prevent contamination. Always clean fib...

Console Cables The supervisor engine's front-panel console ports allow you to connect a terminal or modem to the consoleport. • You can connect a terminal to the console port using one of these options: ◦ The RJ45 console port — Uses an 8-pin RJ-45 connector, and has built-in DTE capability. If the ...

Table 31: Port Mode 1 Signaling and Pinouts (DB-25 Adapter) ConsoleDevice RJ-45-to-DB-25Terminal Adapter RJ-45-to-RJ-45 Rollover Cable Console Port Signal DB-25 Pin RJ-45 Pin RJ-45 Pin Signal CTS 5 8 1 17 RTS DSR 6 7 2 DTR RxD 3 6 3 TxD GND 7 5 4 GND GND 7 4 5 GND TxD 2 3 6 RxD DTR 20 2 7 DSR RTS 4 ...

ConsoleDevice RJ-45-to-DB-25Modem AdapterAdapter RJ-45-to-RJ-45 Rollover Cable Console Port GND 7 4 5 GND TxD 2 3 6 RxD DTR 8 2 7 DSR RTS 5 1 8 20 CTS 19 Pin 1 is connected internally to Pin 8.20 Pin 1 is connected internally to Pin 8. Identifying a Rollover Cable You can identify a rollover cable b...

Mode-Conditioning Patch Cord When using the long-wavelength and long-haul (LX and LH) GBIC with 62.5-micron diameter multimodefiber (MMF), you must install a mode-conditioning patch cord (Cisco product number CAB-GELX-625 orequivalent) between the GBIC and the MMF cable on both the transmit and rece...

Procedure Step 1 Plug the end of the patch cord labeled To Equipment into the GBIC. See Figure 45: Patch Cord Installation, on page 96 . Step 2 Plug the end labeled To Cable Plant into the patch panel. See Figure 45: Patch Cord Installation, on page 96 . The patch cord is 9.8-feet (3-meters) long an...

A P P E N D I X E Troubleshooting • Getting Started, page 103 • Solving Problems at the System Component Level, page 103 • Identifying Startup Problems, page 104 • Troubleshooting the Power Supply Module, page 104 • Troubleshooting the Fan Tray, page 105 • Contacting Cisco Customer Service, page 106...

• Fan tray assembly The chassis fan tray assembly should operate whenever system power is on. You should see the FANLED turn green and hear the fan tray assembly operating. A red FAN LED indicates that one or morefans in the fan tray assembly is not operating. You should immediately contact a Custom...

f) If the IN LED fails to light up after you connect the power supply to a new power source, replace the power cord, and turn on the switch. g) If the IN LED then lights up, return the first power cord for replacement. If this unit has more than one power cord, repeat Step 1 (and all the substeps) f...

Related Topics Fan Tray, on page 4 Air Flow, on page 15 Fan Tray LED, on page 8 Contacting Cisco Customer Service If you are unable to solve a startup problem after using the troubleshooting suggestions in this chapter, contacta Cisco customer service representative for assistance and additional ins...