Cisco 3200 - Manuals

9 Cisco 3200 Series Router Hardware Reference OL-5816-10 For information about using Cisco IOS software to configure Simple Network Management Protocol (SNMP) Management Information Base (MIB) features, see to the appropriate documentation for your network management system. For information on confi...

1-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3270 Router Card Stack The Cisco 3270 Rugged Enclosure supports the following configurations: • One Cisco 3270 Rugged Router card • Up to three Wireless Mobile Interface Cards (WMICs) • One Serial...

1-6 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3230 Router Card Stack The Cisco 3230 Rugged Enclosure can accommodate up to seven cards, including: • One MARC • Up to three WMICs • One SMIC (or no SMIC) • One FESMIC • One MRPC A basic configur...

1-7 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Rugged Enclosure End Caps Each Cisco 3200 Rugged Enclosure has two end caps: an antenna end cap that connects to the back of the enclosure, and an I/O end cap that connects to the front of the enclosure...

1-8 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Note For additional information on antennas and antenna cables, see the “Antenna Basics” technical note at http://www.cisco.com/en/US/products/hw/wireless/ps458/products_installation_guide_chapter09186a...

1-9 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3270 Router I/O End Cap Figure 1-7 shows the Cisco 3270 Router I/O end cap. Figure 1-7 Cisco 3270 Router End Cap The RJ-45 connectors identified as 8, 9, and 10 are Fast Ethernet ports or WMIC con...

1-10 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Note The connectors are sealed at the factory with captive dust covers (not shown) that seal the ports and protect the pins. The dust covers should be used to seal the ports when the ports are not cove...

1-11 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures USB Flash Storage Device Caveat In some cases, using two USB flash storage devices causes unpredictable results (CSCsd11136). If one USB flash storage device is plugged into a USB port and a second USB...

1-12 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3230 Router I/O End Cap Figure 1-8 shows the Cisco 3230 Router I/O end cap. It has multiple connectors that can be used to connect power and data cables. Figure 1-8 Cisco 3230 Router End Cap Note...

1-13 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Protective End Cap Cover A protective end cap cover ( Figure 1-9 ) provides weatherproof protection for the ports on the end caps of the Cisco 3200 Rugged Enclosure when the enclosure is installed outd...

1-15 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures I/O End Cap Port Signals This section describes the ports and port signals on the Cisco 3200 Rugged Enclosure I/O end caps. Gigabit Ethernet Signal Limitations Due to CPU and memory bus limitations, a ...

1-17 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Console Port Signals You can connect to the router or to a Wireless Mobile Interface Card (WMIC) by using a console cable to connect to the console interfaces. The console port signals: • Are asynchron...

1-18 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3200 Rugged Enclosure LED Indications This section describes the LED indications for the Cisco 3200 Rugged Enclosure I/O end caps. Note The behavior of the WMIC LEDs is described in the “WMIC Con...

1-19 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Cisco 3230 Rugged Enclosure I/O End Cap LED Indications Table 1-3 lists the LEDs for the Cisco 3230 Rugged Enclosure I/O end caps and their indications. WMIC Console LEDs WMIC console LEDs function in ...

1-20 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Table 1-5 shows the status of the LEDs when the WMIC is in operational mode. Thermal Plates Cisco 3200 Rugged Enclosures use thermal plates and Wedge Loks to transfer heat from the cards to the extrusi...

1-21 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 1 Cisco 3200 Rugged Enclosures Mounting Brackets Mounting brackets are available for the enclosures. The notches in the mounting brackets allow you to temporarily install the bracket without the router in place. The bolts for the no...

2-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 2 Cisco 3270 Rugged Router Card Note The Cisco 3270 router can be ordered with one Gigabit Ethernet copper interface and one fiber optic interface, or with two Gigabit Ethernet copper interfaces. The port configurations are not inter...

2-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 2 Cisco 3270 Rugged Router Card Cisco 3270 Rugged Router Card Power Requirements The Cisco 3270 Rugged Router card uses +3.3 V, +5 V, and +12 V power sources. Typical power consumption is 20 W. The maximum calculated wattage is 26.5 ...

2-6 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 2 Cisco 3270 Rugged Router Card Ethernet Port Speed and Duplex Mode The router cannot automatically negotiate port speed and duplex mode unless the connecting port is configured speed auto , duplex auto , or no speed . If the port sp...

2-7 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 2 Cisco 3270 Rugged Router Card Cisco 3270 Rugged Router Card Encryption Module The integrated security engine (SEC 2.0) is optimized to handle all the algorithms associated with IP security (IPSec), Secure Sockets Layer (SSL)/Transp...

2-8 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 2 Cisco 3270 Rugged Router Card • 4 crypto channels, each supporting multicommand descriptor chains – Static and/or dynamic assignment of crypto execution units through an integrated controller – Buffer size of 256 bytes for each exe...

3-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 3 Mobile Access Router Card The PCI bus connector supports communication between the Serial Mobile Interface Card (SMIC), the Fast Ethernet Switch Mobile Interface Card (FESMIC), and the Mobile Access Router Card. The Wireless Mobile...

3-3 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 3 Mobile Access Router Card MARC Power Requirements The MARC uses +3.3-V, +5-V, and +12-V power sources. Internal on-board DC-to-DC conversion circuitry generates 1.8 V/1.5 A from the +3.3-V power source. MARC Router Signals Cisco 32...

3-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 3 Mobile Access Router Card Console and Auxiliary Signals You can configure the console interface by using Cisco IOS command line interface (CLI) commands. The console interface and the AUX port can be accessed simultaneously. Also, ...

4-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 4 Fast Ethernet Switch Mobile Interface Card Autonegotiation and Auto-MDI/MDIX All of the Fast Ethernet interfaces support Ethernet autonegotiation for the line transmission speed. Both sides of the connection are automatically set t...

4-3 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 4 Fast Ethernet Switch Mobile Interface Card FESMIC Component Systems The ISA buses and PCI buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards. Both buses comply with the PC/104- Pl...

4-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 4 Fast Ethernet Switch Mobile Interface Card Figure 4-2 shows the 4-port FESMIC header and bus locations. Figure 4-2 4-port FESMIC Header and Bus Locations Note The PC/104- Plus standard requires that the PCI bus and the ISA bus use ...

5-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 5 Serial Mobile Interface Card SMIC Component Systems Figure 5-1 shows the 2-port SMIC header and bus locations. Figure 5-1 2-port SMIC Header and Bus Locations Figure 5-2 shows the 4-port SMIC header and bus locations. Caution If yo...

5-3 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 5 Serial Mobile Interface Card Signals for the SMIC The Cisco Single-sideband (SSB) Serial standard supports the following: • EIA/TIA-232, EIA/TIA-449, EIA-530, EIA-530A, X.21, and V.35 standards in both DTE and DCE modes. • Signals ...

5-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 5 Serial Mobile Interface Card 2-port SMIC Rotary Switch Positions Table 5-4 shows the 2-port SMIC serial signal assignments. The position of the rotary switch determines the port assignments. Although the rotary switch has 8 positio...

5-5 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 5 Serial Mobile Interface Card SMIC Power Consumption The SMIC draws power from the PCI and the ISA connectors. Table 5-6 shows the estimated power consumption. Note that these are theoretical maximum wattages. Table 5-6 SMIC Estimat...

C H A P T E R 6-1 Cisco 3200 Series Router Hardware Reference OL-5816-10 6 Wireless Mobile Interface Cards The Cisco Wireless Mobile Interface Card (WMIC) is a Cisco 3200 Series router interface card in a standard PC/104- Plus form factor. It is one component of the Cisco 3200 Series routers and pro...

6-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards Figure 6-1 shows the WMIC header and bus locations. Figure 6-1 WMIC Header and Bus Locations Note The PC/104-Plus standard requires that the PCI bus and the ISA bus use keying features in the standar...

6-3 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards In contrast, the Serial Mobile Interface Card (SMIC) and FESMIC communicate with the router through the PC/104- Plus bus. The interfaces are configured through the router console port, and all of the...

6-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards LED Behavior During normal operations, the indicator signals (LEDs) on the wireless device have the following meanings: • The status indicator signals operational status. Steady green indicates that ...

6-7 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards MAC Address Allocation The WMIC stores one unique MAC address for the BVI interface. WMIC Power Requirement In a typical Cisco 3200 Series router configuration, the WMIC draws power from the PCI and ...

6-11 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards Universal Workgroup Bridge Limitations The following limitations and restrictions apply to universal workgroup bridges: • A universal workgroup bridge cannot associate with the Cisco WLAN AP when th...

6-13 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards Throughput The throughput is a minimum of: • 4 Mbps half-duplex at one mile line-of-sight range for a 5 MHz -wide channel • 8 Mbps half-duplex at one mile line-of-sight range for a 10 MHz -wide chan...

6-16 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards Additional cards and components provide power and link interfaces to the WMIC. The exact configuration of your router will vary, depending on how the vendor configured it. 5-GHz WMIC (Cisco 3205) Th...

6-17 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 6 Wireless Mobile Interface Cards • •5700 MHz (channel 140) Related Documentation These documents provide detailed information regarding the configuration of the wireless card: • Cisco IOS Switching Services Configuration Guide. Cli...

C H A P T E R 7-1 Cisco 3200 Series Router Hardware Reference OL-5816-10 7 Managing Firmware and Configurations This chapter describes how to manipulate the flash file system, how to copy configuration files, and how to archive (upload and download) software images. It consists of these sections: • ...

7-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with the Flash File System * 16128000 11118592 flash rw flash: 16128000 11118592 unknown rw zflash: 32768 26363 nvram rw nvram: - - network rw tftp: - - opaque rw null: - - opaque rw sys...

7-3 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with the Flash File System By default, the default file system is flash:. You can display the current default file system as specified by the cd command by using the pwd privileged EXEC ...

7-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with the Flash File System To delete a directory with all its files and subdirectories, use the delete /force /recursive filesystem :/ file-url privileged EXEC command. Use the /recursiv...

7-5 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with the Flash File System For specific examples of using the copy command with configuration files, see the “Working with Configuration Files” section on page 7-7 . To copy software ima...

7-6 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with the Flash File System For flash:/ file-url , specify the location on the local flash file system from which the new tar file is created. You can also specify an optional list of fil...

7-7 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files • For the local flash file system, the syntax is flash: • For the File Transfer Protocol (FTP), the syntax is ftp: [[ // username [ : password ] @ location ] / d...

7-8 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files • To load the same configuration commands on all the access points in your network so that all the access points have similar configurations. You can copy ( uplo...

7-9 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files Configuration File Types and Location Startup configuration files are used during system startup to configure the software. Running configuration files contain t...

7-10 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files tftp 69/udp Note You must restart the inetd daemon after modifying the /etc/inetd.conf and /etc/services files. To restart the daemon, either stop the inetd pro...

7-11 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files Uploading the Configuration File by Using TFTP To upload a configuration file from a WMIC to a TFTP server for storage, follow these steps: Step 1 Verify that t...

7-12 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files If the server has a directory structure, the configuration file is written to or copied from the directory associated with the username on the server. For examp...

7-13 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files This example shows how to copy a configuration file named host1-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 and...

7-14 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files This example shows how to copy the running configuration file named ap2-confg to the netadmin1 directory on the remote host with an IP address of 172.16.101.101...

7-15 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files • The remote username associated with the current TTY (terminal) process. For example, if the user is connected to the router through Telnet and was authenticat...

7-16 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files This example shows how to copy a configuration file named host1-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 and...

7-17 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Configuration Files This example shows how to copy the running configuration file named ap2-confg to the netadmin1 directory on the remote host with an IP address of 172.16.101.101...

7-18 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images To delete a saved configuration from flash memory, use the delete flash: filename privileged EXEC command. Depending on the setting of the file prompt global config...

7-19 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images tar File Format of Images on a Server or Cisco.com Software images located on a server or downloaded from Cisco.com are provided in a tar file format, which contain...

7-20 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Note You must restart the inetd daemon after modifying the /etc/inetd.conf and /etc/services files. To restart the daemon, either stop the inetd process and restart...

7-22 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Uploading an Image File by Using TFTP You can upload an image from the WMIC to a TFTP server. You can later download this image to the WMIC or to another WMIC of th...

7-23 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images • The username specified in the archive download-sw or archive upload-sw privileged EXEC command if a username is specified. • The username set by the ip ftp userna...

7-26 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images If you specify the /leave-old-sw , the existing files are not removed. If there is not enough space to install the new image and keep the running image, the downloa...

7-27 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images The archive upload-sw command builds an image file on the server by uploading these files in order: info, the IOS image, the HTML files, and info.ver. After these f...

7-29 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Downloading an Image File by Using RCP You can download a new image file and replace or keep the current image. Caution For the download and upload algorithms to op...

7-31 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Uploading an Image File by Using RCP You can upload an image from the WMIC to an RCP server. You can later download this image to the same WMIC or to another WMIC o...

7-32 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Cisco 3200 WMIC Image Upload Procedure This section provides the procedures for configuring a Cisco 3200 Series router (referred to as the Mobile Access Router Card...

7-33 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Configuration Example for the MARC hostname MAR ! ip routing ! interface FastEthernet0/0 ip address 20.20.20.1 255.255.255.0 ! interface FastEthernet2/0 no ip addre...

7-34 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images interface FastEthernet0 no ip address bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled no shutdown ! interface BVI1 ip address 20.2...

7-35 Cisco 3200 Series Router Hardware Reference OL-5816-10 Chapter 7 Managing Firmware and Configurations Working with Software Images Configuration Example for the WMIC Attached to Switch Port 3 hostname MAR1-SWITCHPORT3 ! bridge irb ! interface Dot11Radio0 no ip address no ip route-cache no shutd...

A-1 Cisco 3200 Series Router Hardware Reference OL-5816-10 A P P E N D I X A Smart Serial Port External Seal The Smart Serial port is not sealed. When the Smart Serial port is not connected or otherwise in use, the protective cover that is provided should be used to seal the port. When a Smart Seria...

B-1 Cisco 3200 Series Router Hardware Reference OL-5816-10 A P P E N D I X B SFP Module Replacement This chapter describes how to replace small-form-factor pluggable (SFP) modules. SFP modules are inserted into the SFP module slot on the Cisco 3270 Rugged Router card. These modules provide the uplin...

B-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix B SFP Module Replacement Replacing SFP Modules into SFP Module Slots This section describes how to replace an SFP module. Warning Class 1 laser product. Statement 1008 To insert an SFP module into the SFP module slot, follow these s...

B-3 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix B SFP Module Replacement Step 9 Find the send (TX) and receive (RX) markings that identify the top side of the replacement SFP module. Note On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows t...

B-4 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix B SFP Module Replacement Error Messages Error Message Transceiver module inserted in port Explanation The online insertion and removal (OIR) facility detected a newly inserted transceiver module for the interface specified in the er...

C-1 Cisco 3200 Series Router Hardware Reference OL-5816-10 A P P E N D I X C Switch Port Functionality The 10/100 Fast Ethernet ports on the Cisco 3200 Series router FESMIC default to Layer 2 switch ports. The FESMIC is a “learning bridge,” as defined in 802.1D with the Virtual Local Area Network (V...

C-9 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality Switch Virtual Interface Switch Virtual Interface A Switch Virtual Interface (SVI) represents a VLAN of switch ports as one interface to the routing or bridging function in the system. Only one SVI can be...

C-10 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality IP Multicast Layer 3 Switching IP Multicast Layer 3 Switching This section describes how to configure IP multicast Layer 3 switching. You must enable IP multicast routing globally before you can enable I...

C-11 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality IP Multicast Layer 3 Switching Verifying IP Multicast Layer 3 Hardware Switching Summary The show ip pim interface count command verifies the IP multicast Layer 3 switching enable state on IP PIM interfa...

C-12 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality IP Multicast Layer 3 Switching ICMP unreachables are never sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disa...

C-13 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality Storm Control (132.206.72.28, 224.2.136.89), 00:14:31/00:01:40, flags:CJT Incoming interface:GigabitEthernet4/8, RPF nbr 10.15.1.20, RPF-MFD Outgoing interface list:Null Router# Note The RPF-MFD flag ind...

C-14 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality Storm Control when a threshold for one type of traffic is reached, that type of traffic is dropped. This threshold is specified as a percentage of the total available bandwidth that can be used by broadc...

C-15 Cisco 3200 Series Router Hardware Reference OL-5816-10 Appendix C Switch Port Functionality IGMP Snooping Verifying Storm Control Use the show storm - control command to view switch port characteristics, including the storm control levels set on the interface. To verify storm-control statistics...

IN-1 Cisco 3200 Series Router Hardware Reference OL-5816-10 I N D E X Numerics 2.4 GHz (802.11b/g) WMIC 6-1 3rd-party devices 3-3 4.9 GHz (public safety) WMIC 6-1 5.0 GHz (public safety) WMIC 6-1 802.11a 6-13 802.11b/g 6-11 802.11i 2-7 802.1D 4-1 802.1P 4-1 802.1Q 4-1 A Advanced Encryption Standard ...

Index IN-2 Cisco 3200 Series Router Hardware Reference OL-5816-10 speed auto 2-6 station role 1-19 connectivity problems, solving B-3 console port Cisco 3270 Rugged Router card 2-1 MARC 3-4 WMIC 1-17 WMIC console LEDs 1-19 cooling 1-20 cover, end cap 1-13 crossover cable 4-2 crypto-channels 2-4 D Da...