Cisco 2600XM - Manuals

9 Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement...

10 The brackets for 19-, 23-, and 24-inch racks are shown in Figure 1. Figure 1 Brackets for Rack-Mounting of Routers with 1-RU Chassis Height Attaching Brackets Attach the mounting brackets to the chassis as shown in Figure 2 through Figure 8, using the screws provided. Attach the second bracket to...

12 Figure 7 Bracket Installation for Center Mounting with Rear Panel Forward: 19-, 23-, or 24-Inch Rack Figure 8 Bracket Installation for Center Mounting with Front Panel Forward: 19-, 23-, or 24-Inch Rack Installing Chassis in Rack Install the chassis in the rack. Rack-mounting screws are not provi...

13 Figure 9 Attaching the Brackets for Wall-Mounting Attaching to Wall Attach the chassis to the wall: • Position the end nearest the power cable at the top. • Align screws (not included) with a wall stud, or use wall anchors. Installing on a Desktop If you are installing a Cisco 2610XM, Cisco 2620X...

14 Step 3 Attach the ground lug or ring terminal to the chassis as shown in Figure 10 or Figure 11. For the ground lug, use the two screws with captive locking washers provided. For a ring terminal, use one of the screws provided. Use a number 2 Phillips screwdriver, and tighten the screws to a torq...

15 Power Connections Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Note The installation must comply with all required electrical codes applicable at the installation site. Connecting Routers to AC Power If your router uses AC power, conn...

16 Wiring Procedure for Nominal 48 VDC Input To connect the router to a DC power source, perform this procedure: Step 1 Remove power from the DC circuit. To ensure that power is removed from the DC circuit, locate the circuit breaker for the DC circuit, switch the circuit breaker to the OFF position...

17 Connecting Routers to the Cisco Redundant Power System If your router uses the Cisco Redundant Power System (RPS), refer to the Cisco RPS Hardware Installation Guide for instructions about the power connections. To locate these documents, see the “Where to Go Next” section on page 24. WAN, LAN, a...

18 5 Power Up the Router Checklist for Power-Up You are ready to power up the Cisco router after you have completed the following steps: • Chassis is securely mounted and grounded. • Power and interface cables are connected. • Your PC terminal emulation program is configured for 9600 baud, 8 data bi...

19 You may see different startup messages: • If you see the following messages, the router has booted with a configuration file and is ready for initial configuration using the Cisco Router and Security Device Manager (SDM): yourname con0 is now available Press RETURN to get started. See the “Initia...

20 Initial Configuration Using Cisco Router and Security Device Manager If the following messages appear at the end of the startup sequence, Cisco Router and Security Device Manager (SDM) is installed on your router: yourname con0 is now available Press RETURN to get started. For instructions on con...

22 Step 11 The configuration appears: The following configuration command script was created: hostname 2610 enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-server community public ! no ip routing ! interface FastEthernet0/0 no shutdown media-ty...

23 For interface numbering information, see the “Interface Numbering” section on page 23. Step 1 To proceed with manual configuration using the CLI, enter no . Would you like to enter the initial configuration dialog? [yes/no]: no Step 2 Press Return to terminate autoinstall and continue with manual...

24 • First built-in Ethernet interface—Ethernet 0/0 • Second built-in Ethernet interface—Ethernet 0/1, or optionally in Cisco 2612 and Cisco 2613 only: Token Ring interface 0/0 Figure 13 Interface Numbering in Chassis with 1-RU Height Voice Interface Numbering Voice interfaces are numbered as follow...

25 To access documentation using Cisco Connection Online (CCO): For Cisco 2600XM series platform documentation, start on Cisco.com at http://www.cisco.com , and click the “Technical Documentation” tab under Useful Links. Under the Product Documentation heading, navigate to Modular Access Routers and...

26 11 Obtaining Technical Assistance For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support...

27 12 Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, ...