Page 3 - DLP-E103 Initiate a Manual Switch on a Path Protection Circuit
17-3 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E102 Apply a Lockout in a 1+1 Group Step 6 Click Yes in the confirmation dialog box. The lock on has been applied and traffic cannot be switched from that port. See the “DLP-E168 Clear a Lock On or Lockout in a 1+1 Protecti...
Page 4 - DLP-E104 Initiate a Force Switch to a Path Protection Circuit
17-4 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E104 Initiate a Force Switch to a Path Protection Circuit Step 2 Click the path you want to switch and then click Edit . Step 3 In the Edit Circuit window, click the Path Protection Selectors tab. Step 4 In the Switch State...
Page 5 - DLP-E105 Create a DCC Tunnel; Provisioning > Overhead Circuits; Purpose
17-5 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E105 Create a DCC Tunnel DLP-E105 Create a DCC Tunnel Note The ONS 15600 can support up to 64 DCC tunnels. Terminated SDCCs cannot be used as a DCC tunnel endpoint, and an SDCC that is used as a DCC tunnel endpoint cannot b...
Page 6 - Finish; DLP-E106 Clean Fiber Connectors
17-6 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E106 Clean Fiber Connectors Step 5 In the Destination area, complete the following: • Node—Choose the destination node. • Slot—Choose the destination slot. • Port—Choose the destination port. • Channel—Shown if you chose DC...
Page 7 - DLP-E107 Clean the Fiber Adapters
17-7 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E107 Clean the Fiber Adapters b. Place the connector tip at the top of the slot at a slight angle. In a single stroke, move the connector down the wipe without lifting the connector from the wipe. Before lifting the connect...
Page 8 - DLP-E108 Verify that a 1+1 Working Port is Active; Maintenance > Protection
17-8 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E108 Verify that a 1+1 Working Port is Active d. Remove and insert the scrub tool tip several times to clean the fiber adapter. Step 3 To remove loose particles from the fiber adapter: a. Remove the dust cap from the rinse ...
Page 11 - DLP-E110 Assign a Name to a Port
17-11 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E110 Assign a Name to a Port DLP-E110 Assign a Name to a Port Step 1 Double-click the card that has the port you want to provision. Step 2 Click the Provisioning tab. Step 3 Click the Port Name column for the port number y...
Page 14 - DLP-E114 Provision Section DCC Terminations
17-14 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E114 Provision Section DCC Terminations DLP-E114 Provision Section DCC Terminations Step 1 In node view, click the Provisioning > Comm Channels > SDCC tabs. Step 2 In the SDCC Terminations area, click Create . Step 3...
Page 15 - Next
17-15 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E114 Provision Section DCC Terminations Step 8 If you checked OSI, complete the following steps. If you checked IP only, continue with Step 9 . a. Click Next . b. Provision the following fields: – Router—Choose the OSI rou...
Page 16 - DLP-E115 Change the Service State for a Port
17-16 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E115 Change the Service State for a Port DLP-E115 Change the Service State for a Port Step 1 In node view, double-click the card with the port(s) you want to put in or out of service. The card view appears. Step 2 Click th...
Page 17 - DLP-E119 Set Auto-Refresh Interval for Displayed PM Counts
17-17 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E116 Remap the K3 Byte Step 8 Return to your originating procedure (NTP). DLP-E116 Remap the K3 Byte Caution If you remap the K3 byte, remap to the same extended byte (Z2, E2, or F1) on either side of the span. Step 1 In n...
Page 18 - DLP-E120 Remove the Narrow CRMs
17-18 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E120 Remove the Narrow CRMs Step 3 From the Auto-refresh drop-down list choose one of the following options: • None : This option disables the auto-refresh feature. • 15 Seconds : This option sets the window auto-refresh t...
Page 20 - DLP-E122 Manual Switch the Node Timing Reference
17-20 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E121 Replace the Existing 600-mm Kick Plates with 900-mm Kick Plates DLP-E121 Replace the Existing 600-mm Kick Plates with 900-mm Kick Plates Step 1 Using the screwdriver, remove the five screws located on the 600-mm (23.6...
Page 21 - DLP-E123 Clear a Manual Switch on a Node Timing Reference
17-21 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E123 Clear a Manual Switch on a Node Timing Reference This operation commands the node to switch to the reference you have selected if the SSM quality of the reference is not lower than the current timing reference. Step 4...
Page 22 - DLP-E124 Set the Optical Power Received Nominal Value
17-22 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E124 Set the Optical Power Received Nominal Value DLP-E124 Set the Optical Power Received Nominal Value Step 1 In node view, double-click the OC-N card that you want to provision. The card view appears. Step 2 Click the Pr...
Page 23 - DLP-E126 Provision the IIOP Listener Port on the CTC Computer
17-23 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E126 Provision the IIOP Listener Port on the CTC Computer • Other Constant—If Port 683 is not used, type the IIOP port specified by your firewall administrator. Step 3 Click Apply . Step 4 When the Change Network Configura...
Page 24 - DLP-E127 Edit Path Protection Circuit Path Selectors
17-24 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E127 Edit Path Protection Circuit Path Selectors DLP-E127 Edit Path Protection Circuit Path Selectors Step 1 Click the Circuits tab. Step 2 In the Circuits tab, click the path protection circuit that you want to edit. To c...
Page 25 - Provisioning > General; Apply
17-25 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E128 Change the Node Name, Date, Time, and Contact Information DLP-E128 Change the Node Name, Date, Time, and Contact Information Note Changing the date, time, or time zone might invalidate node performance monitoring coun...
Page 26 - DLP-E130 Change Security Policy on a Single Node
17-26 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E129 Enable Dialog Box Do-Not-Display Option DLP-E129 Enable Dialog Box Do-Not-Display Option Note If any user who has rights to perform an operation (for example, creating a circuit) selects the “Do not show this dialog a...
Page 27 - DLP-E131 Change Security Policy on Multiple Nodes
17-27 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E131 Change Security Policy on Multiple Nodes Step 3 In the User Lockout area, you can modify the following: • Failed Logins Before Lockout—Choose the number of failed login attempts a user can make before the user is lock...
Page 29 - DLP-E133 Change User and Security Settings for Multiple Nodes
17-29 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E133 Change User and Security Settings for Multiple Nodes Note User settings that you changed during this task will not appear until that user logs off and logs back in again. Step 5 Return to your originating procedure (N...
Page 30 - DLP-E135 Log Out a User on a Single Node; DLP-E136 Log Out a User on Multiple Nodes
17-30 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E135 Log Out a User on a Single Node DLP-E135 Log Out a User on a Single Node Step 1 In node view, click the Provisioning > Security > Active Logins tabs. Step 2 Choose the user you want to log out. Step 3 Click Logo...
Page 31 - DLP-E137 Check the Network for Alarms and Conditions; DLP-E140 Disable Proxy Service Using Internet Explorer (Windows)
17-31 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E137 Check the Network for Alarms and Conditions Step 7 Click OK . A confirmation dialog box appears. Step 8 Click OK . Step 9 Return to your originating procedure (NTP). DLP-E137 Check the Network for Alarms and Condition...
Page 32 - DLP-E141 Disable Proxy Service Using Netscape (Windows and UNIX)
17-32 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E141 Disable Proxy Service Using Netscape (Windows and UNIX) Note If your computer is running Windows XP, you can select Control Panel directly from the Start menu. Make sure that you are in Classic View before continuing ...
Page 33 - DLP-E142 Install the Narrow CRMs
17-33 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E142 Install the Narrow CRMs DLP-E142 Install the Narrow CRMs Step 1 On the bottom left and bottom right, install the cable radius (2 screws). Step 2 Lift the right-side narrow CRM and align it with the three screw holes y...
Page 34 - DLP-E143 Install the Wide CRMs
17-34 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E143 Install the Wide CRMs DLP-E143 Install the Wide CRMs Note If you are installing CRMs on more than one shelf, it is easiest to install the lowest CRMs first. Note If your site uses under-floor cabling, mount the CRMs o...
Page 37 - Go; Yes; DLP-E145 Connect the PDU Ground Cables to the PDU
17-37 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E145 Connect the PDU Ground Cables to the PDU • Activate/Revert—Check this box to activate the uploaded software (if the software is a later than the installed version) or revert to the uploaded software (if the software i...
Page 39 - DLP-E146 Install Isolated Logic Ground
17-39 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E146 Install Isolated Logic Ground DLP-E146 Install Isolated Logic Ground Step 1 Remove the PDU safety cover on the right side. Step 2 Remove the metal shunt connecting the frame ground to the logic ground terminals. Termi...
Page 40 - DLP-E147 Check BLSR or Path Protection Alarms and Conditions
17-40 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E147 Check BLSR or Path Protection Alarms and Conditions DLP-E147 Check BLSR or Path Protection Alarms and Conditions Step 1 From the View menu, choose Go to Network View . Verify that all BLSR or path protection spans on ...
Page 41 - DLP-E152 Install Public-Key Security Certificate
17-41 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E152 Install Public-Key Security Certificate b. In the Set West Protection Operation dialog box, choose CLEAR from the drop-down list. Click OK . c. In the Confirm BLSR Operation dialog box, click Yes . Step 5 To clear a F...
Page 43 - DLP-E154 Delete Alarm Severity Profiles
17-43 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E154 Delete Alarm Severity Profiles Step 3 Click Apply and OK . Note Setting the Maximum History Entries value to the high end of the range uses more CTC memory and could impair CTC performance. Note This task changes the ...
Page 44 - DLP-E155 Enable Alarm Filtering
17-44 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E155 Enable Alarm Filtering Step 9 To remove the alarm profile from the Provisioning > Alarm Profiles > Alarm Profile Editor window, right-click the column of the profile you deleted and choose Remove from the shortc...
Page 46 - DLP-E156 Modify Alarm and Condition Filtering Parameters
17-46 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E156 Modify Alarm and Condition Filtering Parameters DLP-E156 Modify Alarm and Condition Filtering Parameters Step 1 In the node, network, or card view, click the Alarms tab. Step 2 Click the Filter button at the lower-lef...
Page 47 - DLP-E157 Disable Alarm Filtering
17-47 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E157 Disable Alarm Filtering DLP-E157 Disable Alarm Filtering Step 1 In the node, network, or card view, click the Alarms tab. Step 2 Click the Filter tool at the lower-right side of the bottom toolbar. Alarm filtering is ...
Page 48 - DLP-E159 Manually Lock or Unlock a User on Multiple Nodes
17-48 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E159 Manually Lock or Unlock a User on Multiple Nodes Step 6 Click OK . Step 7 Return to your originating procedure (NTP). DLP-E159 Manually Lock or Unlock a User on Multiple Nodes Step 1 From the View menu, chose Go To Ne...
Page 49 - DLP-E160 Verify BLSR Extension Byte Mapping; DLP-E161 Single Shelf Control Card Switch Test
17-49 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E160 Verify BLSR Extension Byte Mapping DLP-E160 Verify BLSR Extension Byte Mapping Step 1 In network view, double-click one of the BLSR nodes with OC-N trunk cards that will be reconnected after a BLSR node removal. Step ...
Page 51 - DLP-E163 Delete Circuits
17-51 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E163 Delete Circuits DLP-E163 Delete Circuits Step 1 Complete the “NTP-E69 Back Up the Database” procedure on page 14-4 . Step 2 Investigate all network alarms and resolve any problems that could be affected by the circuit...
Page 53 - DLP-E167 Clear a Manual or Force Switch in a 1+1 Protection Group
17-53 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E167 Clear a Manual or Force Switch in a 1+1 Protection Group Step 6 Complete the “NTP-E11 Install the OC-N Cards” procedure on page 2-4 . Step 7 Return to your originating procedure (NTP). DLP-E167 Clear a Manual or Force...
Page 54 - DLP-E169 Initiate a Lockout on a Path Protection Path
17-54 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E169 Initiate a Lockout on a Path Protection Path Step 2 In the Protection Groups area, choose the protection group that contains the card you want to clear. Step 3 In the Selected Group area, choose the card you want to c...
Page 55 - DLP-E170 Clear a Switch or Lockout on a Path Protection Circuit; DLP-E171 Verify Fan Operation
17-55 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E170 Clear a Switch or Lockout on a Path Protection Circuit DLP-E170 Clear a Switch or Lockout on a Path Protection Circuit Step 1 Click the Circuits > Circuits tabs. Step 2 Click the path you want to switch and click E...
Page 57 - Prerequisite Procedures
17-57 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E172 Install Fiber-Optic Cables for Path Protection Configurations DLP-E172 Install Fiber-Optic Cables for Path Protection Configurations Caution To avoid loss of traffic, do not create a path protection using two ports on...
Page 59 - DLP-E177 Change Tunnel Type
17-59 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E177 Change Tunnel Type DLP-E177 Change Tunnel Type Step 1 From the View menu, choose Go to Network View . Step 2 Click the Provisioning > Overhead Circuits tabs. Step 3 Click the circuit tunnel that you want to convert...
Page 60 - DLP-E179 Repair an IP Tunnel
17-60 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E179 Repair an IP Tunnel Step 1 From the View menu, choose Go to Network View . Step 2 Click the Provisioning > Overhead Circuits tabs. Step 3 Click the overhead circuit that you want to delete. Step 4 Click Delete . St...
Page 61 - J1 Function
17-61 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E180 Provision Path Trace on Circuit Source and Destination Ports DLP-E180 Provision Path Trace on Circuit Source and Destination Ports Note This task assumes you are setting up path trace on a bidirectional circuit and se...
Page 64 - DLP-E181 Provision Path Trace on OC-N Ports
17-64 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E181 Provision Path Trace on OC-N Ports The expect and receive strings are updated every few seconds if the Path Trace Mode field is set to Auto or Manual. Step 11 Click Close . The detailed circuit window indicates path t...
Page 65 - DLP-E182 Create Login Node Groups
17-65 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E182 Create Login Node Groups Step 7 If you set the Path Trace Mode field to Manual, enter the string that the OC-N port should receive in the New Expected String field. To do this, trace the circuit path on the detailed c...
Page 66 - DLP-E183 Delete a Node from the Current Session or Login Group
17-66 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E183 Delete a Node from the Current Session or Login Group Figure 17-10 Login Node Group Step 8 Return to your originating procedure (NTP). DLP-E183 Delete a Node from the Current Session or Login Group Step 1 From the Vie...
Page 67 - DLP-E184 Configure the CTC Alerts Dialog Box for Automatic Popup
17-67 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E184 Configure the CTC Alerts Dialog Box for Automatic Popup DLP-E184 Configure the CTC Alerts Dialog Box for Automatic Popup Step 1 Click the CTC Alerts toolbar icon. Step 2 In the CTC Alerts dialog box, choose one of the...
Page 69 - DLP-E187 Delete a Node from a Specified Login Node Group
17-69 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E187 Delete a Node from a Specified Login Node Group DLP-E187 Delete a Node from a Specified Login Node Group Step 1 From the CTC Edit menu, choose Preferences . Step 2 In the Preferences dialog box, click the Login Node G...
Page 70 - DLP-E189 Provision Line DCC Terminations
17-70 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E189 Provision Line DCC Terminations • OOS,MT—Puts the circuit cross-connects in the OOS-MA,MT service state. This service state does not interrupt traffic flow and allows loopbacks to be performed on the circuit, but supp...
Page 71 - Set to IS
17-71 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E189 Provision Line DCC Terminations Note User can provision SDCCs and LDCCs (Line DCC) on different ports . User can provision the SONET Line DCCs and SDCCs (when not used as a DCC termination by the ONS 15600) as DCC tun...
Page 72 - DLP-E190 Provision a Proxy Tunnel
17-72 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E190 Provision a Proxy Tunnel – IIH—Sets the Intermediate System to Intermediate System Hello PDU propagation frequency. The IS-IS Hello PDUs establish and maintain adjacencies between ISs. The default is 3 seconds. The ra...
Page 73 - DLP-E191 Provision a Firewall Tunnel; Create
17-73 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E191 Provision a Firewall Tunnel Step 5 Continue with your originating procedure (NTP). DLP-E191 Provision a Firewall Tunnel Note If the proxy server is configured as proxy-only or is disabled, you cannot set up a firewall...
Page 74 - DLP-E192 Delete a Proxy Tunnel
17-74 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E192 Delete a Proxy Tunnel DLP-E192 Delete a Proxy Tunnel Step 1 Click the Provisioning > Network > Proxy subtabs. Step 2 Click the proxy tunnel that you want to delete. Step 3 Click Delete . Step 4 Continue with you...
Page 75 - DLP-E196 Change a Section DCC Termination
17-75 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E196 Change a Section DCC Termination DLP-E196 Change a Section DCC Termination Step 1 Click the Provisioning > Comm Channels > SDCC tabs. Step 2 Click the SDCC that you want to change. Step 3 Click Edit . Step 4 In ...
Page 76 - DLP-E198 Delete a Section DCC Termination
17-76 Cisco ONS 15600 Procedure Guide, R8.0 Chapter 17 DLPs E100 to E199 DLP- E198 Delete a Section DCC Termination • Far End is Foreign—Check this box to specify that the LDCC termination is a non-ONS node. • Far end IP—If you checked the Far End is Foreign check box, type the IP address of the far...
Cisco MGX-FRSM-HS2
Manual
Cisco 3545
Manual
Cisco Dial NMS
Manual
Cisco DOC-7813565=
Manual
Cisco 2620
Manual
Cisco CP7910GRF
Manual
Cisco ME-C6524GS-8S
Manual
Cisco OL-2056-02
Manual
Cisco TD 92322GB
Manual
Cisco OL-11524-01
Manual
Cisco OL-5532-02
Manual
Cisco VG204XM
Manual
Cisco DS71-MD4
Manual
Cisco 247933900
Manual
Cisco 4.5
Manual