Cisco 12000 Series - Manuals

Page 2 - Hardware Revision Requirements, page 3; ATM Line Card Product Numbers; Router Hardware Installation; Supported Platforms; The ATM line card is supported on all Cisco 12000 series routers.; Cisco IOS Software Release Requirements; ATM Line Card

2 ATM Line Card Installation and Configuration OL-13004-01 Important Information • Hardware Revision Requirements, page 3 • Related Documentation, page 4 ATM Line Card Product Numbers Table 1 lists the Cisco product numbers to which this publication applies. Router Hardware Installation For hardware...

Page 3 - show version; Hardware Revision Requirements; show version; Table 3

3 ATM Line Card Installation and Configuration OL-13004-01 Important Information Table 2 lists the Cisco IOS releases and other software components that are compatible with the various ATM line cards. The show version and show hardware commands display the current hardware configuration of the route...

Page 4 - Related Documentation; Cisco IOS Configuration Fundamentals Configuration Guide; Product Overviews; Ejector lever

4 ATM Line Card Installation and Configuration OL-13004-01 Product Overviews Related Documentation This publication describes the basic installation and configuration of a ATM line card. For complete software and ATM configuration information, refer to the following publications: • Cisco 12000 Serie...

Page 5 - Figure 3

5 ATM Line Card Installation and Configuration OL-13004-01 Product Overviews 4-port OC-3c/STM-1 ATM Line Card Overview The 4-port OC-3c/STM-1 ATM line card interfaces with the switch fabric of the Cisco 12000 Series Router. It provides four 155-Mbps OC-3c/STM-1c duplex SC single-mode or multimode SO...

Page 7 - Preparing for Installation; Safety Guidelines, page 7; Safety Guidelines; Note

7 ATM Line Card Installation and Configuration OL-13004-01 Preparing for Installation Figure 5 shows the front view of the 4-port ISE ATM line card. Figure 5 4-port ISE ATM Line Card Preparing for Installation Before you begin the installation process, review the important information in the followi...

Page 8 - Preventing Electrostatic Discharge; The following are guidelines for preventing ESD damage:; Required Tools and Equipment; Flat-blade or Phillips screwdriver; Removing and Installing a Line Card

8 ATM Line Card Installation and Configuration OL-13004-01 Removing and Installing a Line Card Preventing Electrostatic Discharge Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Electromag...

Page 9 - Guidelines for Line Card Removal and Installation; shutdown; command before removing a line card.; configure; Caution

9 ATM Line Card Installation and Configuration OL-13004-01 Removing and Installing a Line Card Note The installation and removal procedure for the ATM line card is different for the Cisco 12008 and Cisco 12012 routers than for the other Cisco 12000 series routers. Make sure you refer to the procedur...

Page 10 - Removing a Line Card; Figure 6

10 ATM Line Card Installation and Configuration OL-13004-01 Removing and Installing a Line Card Caution When you remove a line card, always use the eject or levers to ensure that the connector pins disconnect from the backplane in the sequence expected by the router. Any card that is only partially ...

Page 12 - Removing the Blank Filler; Installing a Blank Filler

12 ATM Line Card Installation and Configuration OL-13004-01 Removing and Installing a Line Card Note When removing the 4-port ISE ATM line card, take into account that it weighs approximately 13.2 lb (6 kg). Removing the Blank Filler This procedure only applies to 4-port ISE ATM line cards in Cisco ...

Page 13 - Figure 8

13 ATM Line Card Installation and Configuration OL-13004-01 Removing and Installing a Line Card Step 1 Choose an available pair of slots for the line card, and verify that the fiber-optic interface cables for the line card are long enough for you to reach the line card ports and connect the line car...

Page 14 - before; Installing a Line Card

14 ATM Line Card Installation and Configuration OL-13004-01 Removing and Installing a Line Card To ensure that there is adequate space for the ATM line card, tighten the captive installation screws on the blank filler before you insert the line card. Caution Use the captive screws to prevent acciden...

Page 17 - Line Card Cable-Management Bracket

17 ATM Line Card Installation and Configuration OL-13004-01 Line Card Cable-Management Bracket Figure 10 4-port ISE ATM Line Card Installed with Blank Filler Line Card Cable-Management Bracket Note The illustrations in this section show various line cards, but the line card cable-management bracket ...

Page 18 - The cable-management system consists of two separate components:

18 ATM Line Card Installation and Configuration OL-13004-01 Line Card Cable-Management Bracket The cable-management system consists of two separate components: 1. A cable-management tray that is mounted on the chassis. Refer to the appropriate Cisco 12000 Series Router installation and configuration...

Page 19 - Removing a Line Card Cable-Management Bracket; To remove a line card cable-management bracket, follow these steps:

19 ATM Line Card Installation and Configuration OL-13004-01 Line Card Cable-Management Bracket Note When shipped with spare line card orders, the cable-management bracket is not attached to the line card. You must attach the cable-management bracket to the line card before you insert the line card i...

Page 20 - Chassis cable-management tray

20 ATM Line Card Installation and Configuration OL-13004-01 Line Card Cable-Management Bracket Figure 13 Multiport Line Card Cable-Management Installation and Removal(4-Port OC-48c/STM-16c DPT Line Card Shown) 1 Chassis cable-management tray 3 Line card cable-management bracket 2 Velcro straps 4 Fib...

Page 21 - Installing a Line Card Cable-Management Bracket

21 ATM Line Card Installation and Configuration OL-13004-01 Line Card Cable-Management Bracket Figure 14 Single-Port Line Card Cable-Management Bracket Installation and Removal (1-Port OC-192c/STM-64c DPT Line Card Shown) Installing a Line Card Cable-Management Bracket To install a line card cable-m...

Page 22 - Cabling and Specifications; ATM Line Card Power Budget and Signal Specifications, page 22; ATM Line Card Power Budget and Signal Specifications; Table 4

22 ATM Line Card Installation and Configuration OL-13004-01 Cabling and Specifications Step 2 Attach the line card cable-management bracket to the line card as follows: a. Position the cable-management bracket over the front of the line card faceplate. b. Insert and tighten the captive screw(s) to s...

Page 23 - Table 5

23 ATM Line Card Installation and Configuration OL-13004-01 Cabling and Specifications 4-port OC-3c/STM-1 ATM Line Card Power Specifications The 4-port OC-3c/STM-1 ATM line card provides the Cisco 12000 series router with four 155-Mbps OC-3c/STM-1c duplex SC single-mode or multimode SONET/SDH ATM in...

Page 24 - Table 8; Fiber-Optic Network Interface Cables

24 ATM Line Card Installation and Configuration OL-13004-01 Cabling and Specifications 4-port OC-12c/STM-4c ISE ATM Line Card Power Specifications The 4-port OC-12c/STM-4c ISE ATM line card provides the Cisco 12000 Series Router with four 622-Mbps ATM interfaces. Table 8 lists the power ratings and ...

Page 25 - RX port

25 ATM Line Card Installation and Configuration OL-13004-01 Cabling and Specifications Figure 15 Duplex SC Cable Connector Figure 16 Simplex SC Cable Connector Attach either one duplex fiber cable or two simplex fiber cables per port between the line card and the device to which the line card is con...

Page 26 - Verifying and Troubleshooting Line Card Installation; Initial Boot Process, page 26; Initial Boot Process; If one of these conditions is not met, refer to the

26 ATM Line Card Installation and Configuration OL-13004-01 Verifying and Troubleshooting Line Card Installation Note The fiber-optic connectors must be free of dust, oil, or other contaminants. Before connecting the cable to the line card, carefully clean the fiber-optic connectors using an alcohol...

Page 27 - Alphanumeric LEDs; LED

27 ATM Line Card Installation and Configuration OL-13004-01 Verifying and Troubleshooting Line Card Installation Status LEDs Each 4-port ISE ATM line card provides the following two types of LEDs (see Figure 5 ) for monitoring the operating status of the line card: • Status LEDs – 3 lines grouped ne...

Page 28 - LED Display; nnnn

28 ATM Line Card Installation and Configuration OL-13004-01 Verifying and Troubleshooting Line Card Installation Table 11 Alphanumeric LED Messages During a Typical Initialization Sequence LED Display 1 Meaning Source MROM nnnn MBus microcode execute; nnnn is the microcode version number. MBus contr...

Page 31 - Troubleshooting the Installation; no shutdown

31 ATM Line Card Installation and Configuration OL-13004-01 Verifying and Troubleshooting Line Card Installation Troubleshooting the Installation Note Many new line cards are designated as administratively down by default. Status LEDs are off until you configure the interfaces and use the no shutdow...

Page 32 - Configuring and Troubleshooting Interfaces; Initial Configuration; Parameter; bytes

32 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces The following sections provide procedures for configuring and troubleshooting the ATM line card. • Initial Configuration, page 32 • Configuring an Interfa...

Page 33 - type

33 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces A Cisco 12000 Series Router identifies an interface address by its line card slot number and port number, in the format slot/port . The ATM interfaces on the line card are numbered starting from 0:...

Page 34 - Using show Commands to Check Status; Using the show version Command

34 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces Note On the 4-port OC-3c/STM-1 ATM line card, adjacent ports 0 and 1 share the same framer, and adjacent ports 2 and 3 share another framer. Therefore ports 0 and 1 must use the same configuration ...

Page 35 - Using the show interfaces Command; Using the show running-config Command; ATM Configuration Example

35 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces Using the show interfaces Command The following commands display information about the router interfaces: show interfaces , show interfaces pos slot/port , and show interfaces atm slot/port . The f...

Page 36 - “Important Information” section on page 1; Advanced Line Card Troubleshooting; Output Examples; show context summary Output

36 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces For additional configuration examples, refer to the appropriate Cisco IOS software configuration publications listed in the “Important Information” section on page 1 . Advanced Line Card Troublesho...

Page 37 - show context slot Output; show logging Output; show diag; slot; Output

37 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces • show context slot Output show context summary Output Router# show context summary CRASH INFO SUMMARY Slot 0 : 0 crashes Slot 1 : 1 crashes 1 . crash at 10:36:20 UTC Wed Dec 19 2001 Slot 2 : 0 cra...

Page 38 - The type of failure that has occurred in the; show context slot 2; example is identified by the underlined; Checking the Current Status of the Line Card; show led

38 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces Insertion time: 00:00:10 (5d16h ago) DRAM size: 67108864 bytes FrFab SDRAM size: 134217728 bytes, SDRAM pagesize: 8192 bytes ToFab SDRAM size: 134217728 bytes, SDRAM pagesize: 8192 bytes 1 crash si...

Page 39 - microcode reload; Fabric Ping Failure; You can find more information about this issue on Cisco.com in the; Error Messages

39 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces SLOT 10 : RUN IOS SLOT 11 : RUN IOS SLOT 13 : RUN IOS SLOT 14 : RUN IOS Note It is possible for the value of an alphanumeric LED to be reversed. For example, IOS RUN may be displayed as RUN IOS. If...

Page 40 - FPGA Error Messages; diag; Field Diagnostics for the Cisco

40 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces FPGA Error Messages If the line card does not boot and you receive an error message indicating that there is a problem with the Field-Programmable Gate Array (FPGA) image (or if the line card alpha...

Page 41 - verbose; reload; previous

41 ATM Line Card Installation and Configuration OL-13004-01 Configuring and Troubleshooting Interfaces Cisco initiated this change to accommodate users with 20-MB Flash memory cards. Field diagnostics are now stored and maintained as a separate image under the following name: c12k-fdiagsbflc-mz-xxx-...

Page 43 - Line Card Memory; Line Card Memory Locations

43 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Line Card Memory Caution The user serviceability of memory modules varies from line card to line card. Read this section carefully before attempting to remove or install any line card memory module. ATM line cards include t...

Page 45 - ISE Line Card Memory Locations

45 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Engine 2 Line Card Memory Locations Figure 19 shows the DIMM socket locations on an Engine 2 line card. This line card is equipped with eight DIMM sockets: • Two route memory DIMM sockets • Two pairs of packet memory DIMM s...

Page 46 - describes the various memory upgrade options.; Verifying Memory Installation; show hardware; command. The DRAM DIMM; Route memory SODIMM0; Line Card

46 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Figure 20 ATM ISE Line Card Memory Locations There are two route memory sockets on ATM ISE (Engine 3) line cards that support the addition of route memory modules. Table 15 describes the various memory upgrade options. Veri...

Page 47 - ATM Line Card Route Memory Options; Total Route Memory

47 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory LC-Slot3# show hardware Cisco Internetwork Operating System Software IOS (tm) GS Software (GLC1-LC-M), Experimental Version 12.0(20050203:211853) [samson-1g_cli_ci 144] Copyright (c) 1986-2005 by cisco Systems, Inc. Compile...

Page 48 - Removing and Installing Line Card Memory; Engine Number Total Packet Memory

48 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory ATM Line Card Packet Memory Options Line card packet memory temporarily stores data packets awaiting switching decisions by the line card processor. Once the line card processor makes the switching decisions, the packets ar...

Page 49 - Removing a DIMM

49 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Caution The user serviceability of memory modules varies from line card to line card. Read this section carefully before attempting to remove or install any line card memory module. This section contains the following proce...

Page 50 - Installing a DIMM

50 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Figure 22 DIMM Socket with Single Release Lever Step 4 Use the socket release levers to eject the DIMM. • For a socket with dual release levers (see Figure 21 ), pull down both levers at the same time to eject the DIMM. or ...

Page 51 - Removing a SODIMM

51 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory If necessary, rock the DIMM back and forth gently to align it in the socket. Figure 23 Handling a DIMM Caution When inserting DIMMs into a socket, apply firm, but not excessive, pressure. If you damage a DIMM socket, you mu...

Page 53 - Insert a DIMM removal tool

53 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Step 5 Remove the SODIMM0: a. Insert a DIMM removal tool 1 between the SODIMM and release latch on each side of SODIMM0. b. Gently move the tools in an outward direction to open the latches and release the module (see Figur...

Page 54 - As the SODIMM is released, it positions itself at a 45-degree angle (

54 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Step 6 As the SODIMM is released, it positions itself at a 45-degree angle ( Figure 26 a). Gently pull out the SODIMM module from the socket. Continue to keep the module at a 45-degree angle until it is completely removed f...

Page 55 - Installing a SODIMM; Use the following procedure to install a SODIMM.

55 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Installing a SODIMM Use the following procedure to install a SODIMM. Note If you are installing both SODIMMs, be sure to install SODIMM0 first. Step 1 Attach an ESD-preventive wrist or ankle strap and follow its instruction...

Page 56 - The SODIMM must be aligned at a 45-degree angle (

56 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Figure 29 SODIMM with Key in Face-Up Position Step 7 The SODIMM must be aligned at a 45-degree angle ( Figure 30 a). Note When the key is in the face-up position, the metal traces on the left side of the key measure 0.9 inc...

Page 58 - Checking the Installation of Line Card Memory; To check the installation of line card memory, follow these steps:

58 ATM Line Card Installation and Configuration OL-13004-01 Line Card Memory Figure 32 Retaining Clip Installed into Module Latch Checking the Installation of Line Card Memory After you install line card memory and reinstall the line card in the router, the router reinitializes the line card and det...

Page 59 - Regulatory, Compliance, and Safety Information; Translated Safety Warnings and Agency Approvals; Regulatory; Electromagnetic Compatibility Regulatory Statements; FCC Class A Compliance; Move the equipment farther away from the television or radio.

59 ATM Line Card Installation and Configuration OL-13004-01 Regulatory, Compliance, and Safety Information If the router fails to restart properly after several attempts and you are unable to resolve the problem, access Cisco.com or contact your Cisco service representative for assistance. Before ca...

Page 60 - Canada; English Statement of Compliance; This class A digital apparatus complies with Canadian ICES-003.; French Statement of Compliance; Europe—EU; Warning

60 ATM Line Card Installation and Configuration OL-13004-01 Regulatory, Compliance, and Safety Information CISPR 22 This apparatus complies with CISPR 22/EN55022 Class B radiated and conducted emissions requirements. Canada English Statement of Compliance This class A digital apparatus complies with...

Page 61 - Class A Notice for Hungary

61 ATM Line Card Installation and Configuration OL-13004-01 Regulatory, Compliance, and Safety Information Class A Notice for Hungary Class A Notice for Taiwan and Other Traditional Chinese Markets Class A Notice for Korea Warning This equipment is a class A product and should be used and installed ...

Page 62 - Obtaining Documentation; What’s New in

62 ATM Line Card Installation and Configuration OL-13004-01 Obtaining Documentation Obtaining Documentation For information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New i...