Cisco 1140 - Manuals

7 – Provide your organization’s network administrator with your access point MAC address. Your network administrator will query the DHCP server using the MAC address to identify the IP address. The MAC address is on a label attached to the bottom of the access point. – Use the CLI and serial port to...

8 Assigning an IP Address Using the CLI Follow these steps to access the CLI using a Telnet session. These steps are for a PC running Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions. Step 1 Select Start > Programs > Accessori...

9 5 Mounting the Access Point Cisco Aironet 3500, 1260, 1140, 1130, and 1040 series access points can be mounted in several configurations, including on a suspended ceiling, on a hard ceiling or wall, on an elecrtical or network box, and above a suspended ceiling. Click this URL to browse to complet...

13 – Throughput—Maximizes data volume handled by the access point but might reduce its range. – Range—Maximizes the access point range but might reduce throughput. – Default—The access point uses its default data rate settings for the radio selected. – Custom—The access point uses settings that you ...

14 Note You can restore the access point to its factory defaults by unplugging the power jack and plugging it back in while holding the Mode button down until the Ethernet LED turns amber (approximately 2 to 3 seconds). Enabling the Radio Interfaces The access point radios are disabled by default, a...

16 you cannot create additional SSIDs with WPA authentication because they use different encryption settings. If you find that the security setting for an SSID conflicts with another SSID, you can delete one or more SSIDs to eliminate the conflict. If any VLANs are defined on the access point, the t...

17 • You cannot configure multiple WEP keys. To configure multiple WEP keys, click Security > Encryption Manager . • You cannot assign an SSID to a VLAN that is already configured on the access point. To assign an SSID to an existing VLAN, choose Security > SSID Manager . • You cannot configur...

18 Note If you do not use VLANS on your wireless LAN, the security options that you can assign to multiple SSIDs are limited. Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for VLAN details. 1. Click Apply . The SSID appears in the SSID table at the bottom of the...

20 Configuring System Power Settings After connecting the access point to a power source, its status LED might be amber, which can indicate that the access point is unable to verify that the power source equipment (PSE) is supplying sufficient power. In such cases, you need to configure settings on ...

22 Step 6 Click Apply . The access point reboots configured with the power settings you specified. Note You might have to refresh your browser screen to see the current status indicating that the access point radios are enabled. Finding More Troubleshooting Help If you are still experiencing difficu...

23 Step 8 Select the section that best suits your troubleshooting needs. 8 Access Point Specifications Table 4 lists the technical specifications for the 1140 series autonomous access point. Table 4 Access Point Specifications Category Specification Dimensions (LxWxD) 8.68 x 8.68 x 1.84 in. (22.04 x...

24 9 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation...

25 Manufacturers Federal Communication Commission Declaration of Conformity Statement Manufacturer: Cisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USA This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful i...

26 Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. Caution Withi...

27 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English. Japanese Translation English Translation This equipment operate...

28 Statement 371—Power Cable and AC Adapter English Translation When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits t...

32 Declaration of Conformity for RF Exposure United States This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin 65C rev 01.01. The minimum separation distance...

34 Chinese Translation Operation of Cisco Aironet Access Points in Brazil This section contains special information for operation of Cisco Aironet access points in Brazil. Access Point Models AIR-AP1142N-T-K9 AIR-AP1141N-A-K9

35 Regulatory Information Figure 5 contains Brazil regulatory information for the access point models identified in the previous section. Figure 5 Brazil Regulatory Information Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferênci...