Page 4 - Overview; Verifying Shipped Components
4 3 Overview This section explains necessary tasks prior to installing the 1140 series access point. Verifying Shipped Components To unpack and verify the contents of the 1140 series access point and accessory kit, follow these steps: Step 1 Unpack and remove the access point and the accessory kit f...
Page 5 - Key Ports and Components
5 Key Ports and Components Familiarize yourself with the access point before continuing with the installation. Figure 2 shows the access point key components. Figure 2 Access Point Ports and Connections 1 Standard ceiling adjustable T-rail clip 3 1140 series access point 2 Mounting bracket 4 6-32 x ...
Page 6 - Performing a Site Survey; Obtaining and Assigning an IP Address
6 Performing a Site Survey Before you mount and deploy your access point, we recommend that you perform a site survey (or use a site planning tool) to determine the best location to install your access point. You should have the following information about your wireless network available: • Access p...
Page 7 - Connecting to the Access Point Locally; Assigning the IP Address to the BVI
7 – Provide your organization’s network administrator with your access point MAC address. Your network administrator will query the DHCP server using the MAC address to identify the IP address. The MAC address is on a label attached to the bottom of the access point. – Use the CLI and serial port to...
Page 8 - Assigning an IP Address Using the CLI
8 Assigning an IP Address Using the CLI Follow these steps to access the CLI using a Telnet session. These steps are for a PC running Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions. Step 1 Select Start > Programs > Accessori...
Page 9 - Mounting the Access Point; Configuring Basic Settings
9 5 Mounting the Access Point Cisco Aironet 3500, 1260, 1140, 1130, and 1040 series access points can be mounted in several configurations, including on a suspended ceiling, on a hard ceiling or wall, on an elecrtical or network box, and above a suspended ceiling. Click this URL to browse to complet...
Page 13 - Default Settings on the Express Setup Page
13 – Throughput—Maximizes data volume handled by the access point but might reduce its range. – Range—Maximizes the access point range but might reduce throughput. – Default—The access point uses its default data rate settings for the radio selected. – Custom—The access point uses settings that you ...
Page 14 - Enabling the Radio Interfaces; Configuring Security Settings
14 Note You can restore the access point to its factory defaults by unplugging the power jack and plugging it back in while holding the Mode button down until the Ethernet LED turns amber (approximately 2 to 3 seconds). Enabling the Radio Interfaces The access point radios are disabled by default, a...
Page 16 - Express Security Types; Express Security Limitations
16 you cannot create additional SSIDs with WPA authentication because they use different encryption settings. If you find that the security setting for an SSID conflicts with another SSID, you can delete one or more SSIDs to eliminate the conflict. If any VLANs are defined on the access point, the t...
Page 17 - Using the Express Security Page
17 • You cannot configure multiple WEP keys. To configure multiple WEP keys, click Security > Encryption Manager . • You cannot assign an SSID to a VLAN that is already configured on the access point. To assign an SSID to an existing VLAN, choose Security > SSID Manager . • You cannot configur...
Page 18 - Troubleshooting; Checking the Access Point LED
18 Note If you do not use VLANS on your wireless LAN, the security options that you can assign to multiple SSIDs are limited. Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for VLAN details. 1. Click Apply . The SSID appears in the SSID table at the bottom of the...
Page 20 - Configuring System Power Settings
20 Configuring System Power Settings After connecting the access point to a power source, its status LED might be amber, which can indicate that the access point is unable to verify that the power source equipment (PSE) is supplying sufficient power. In such cases, you need to configure settings on ...
Page 22 - Finding More Troubleshooting Help
22 Step 6 Click Apply . The access point reboots configured with the power settings you specified. Note You might have to refresh your browser screen to see the current status indicating that the access point radios are enabled. Finding More Troubleshooting Help If you are still experiencing difficu...
Page 23 - Access Point Specifications
23 Step 8 Select the section that best suits your troubleshooting needs. 8 Access Point Specifications Table 4 lists the technical specifications for the 1140 series autonomous access point. Table 4 Access Point Specifications Category Specification Dimensions (LxWxD) 8.68 x 8.68 x 1.84 in. (22.04 x...
Page 24 - Declarations of Conformity and Regulatory Information
24 9 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation , which also lists all new and revised Cisco technical documentation...
Page 25 - FOR HOME OR OFFICE USE
25 Manufacturers Federal Communication Commission Declaration of Conformity Statement Manufacturer: Cisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USA This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful i...
Page 26 - VCCI Statement for Japan
26 Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. Caution Withi...
Page 27 - Guidelines for Operating Cisco Aironet Access Points in Japan; Japanese Translation
27 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English. Japanese Translation English Translation This equipment operate...
Page 28 - Statement 371—Power Cable and AC Adapter; English Translation; Industry Canada; Canadian Compliance Statement
28 Statement 371—Power Cable and AC Adapter English Translation When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits t...
Page 32 - Declaration of Conformity for RF Exposure; United States; Administrative Rules for Cisco Aironet Access Points in Taiwan
32 Declaration of Conformity for RF Exposure United States This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin 65C rev 01.01. The minimum separation distance...
Page 34 - Chinese Translation; Operation of Cisco Aironet Access Points in Brazil; Access Point Models
34 Chinese Translation Operation of Cisco Aironet Access Points in Brazil This section contains special information for operation of Cisco Aironet access points in Brazil. Access Point Models AIR-AP1142N-T-K9 AIR-AP1141N-A-K9
Page 35 - Regulatory Information; Portuguese Translation
35 Regulatory Information Figure 5 contains Brazil regulatory information for the access point models identified in the previous section. Figure 5 Brazil Regulatory Information Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferênci...
