Chief WM210-220230-240S/SI - Manuals

Page 2 - Installation Instructions; DISCLAIMER; maximum; Table 1: Weight Capacities

Installation Instructions 2 DISCLAIMER Milestone AV Technologies and its affiliated corporations andsubsidiaries (collectively “Milestone”), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,conditions or variat...

Page 3 - TABLE OF CONTENTS; WM2XXSI/WM2XXAUSI Interactive Model Only . 8

Installation Instructions 3 TABLE OF CONTENTS Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . 3 Dimensions . . . . . . . . . . . . . . . . . . . ...

Page 4 - DIMENSIONS

Installation Instructions 4 DIMENSIONS 10.81 7.25 .75 16.00 11.53 .34 7.25 3.96 5.64 210S, TRAVEL 12.75" - 19.5" 240S, TRAVEL 37.2" - 65.6" 3 OF 5.36 19.63 1.42 1.09 CABLE CHANNEL DIMENSIONS THRU ARM DIMENSIONS: INCHES WM2XXS/WM2XXAUS (Standard Model) 10.81 274.64 7.25 184.14 .75 19....

Page 5 - LEGEND

Installation Instructions 5 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio...

Page 6 - TOOLS REQUIRED FOR INSTALLATION; [wall bracket; All Models

Installation Instructions 6 TOOLS REQUIRED FOR INSTALLATION PARTS 1/2” (12.7mm) #2 7/32” (5.6mm) 3/8” (9.5mm) 3/16” (included) 5/32” (included) (security) 1/2” (12.7mm) 5/32” - 6" long (included) (security) D (2) [wall bracket E (2) 1/4-20 x 5/8” H (4) 1/4-20 x 1-1/2” K (4) N (4) 1/4-20 x 1-3/4”...

Page 7 - Figure 1; Drywall

Installation Instructions 7 SITE REQUIREMENTS - Steel Stud Structure (All Models) WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto asteel s...

Page 8 - tighten the cap; only; Minimum System Requirements; Ultrasound Reflections; Figure 2; Drawing surface; Motion sensor

Installation Instructions 8 WS2XXSI/WS2XXAUSI INTERACTIVEMODELS ONLY The Chief Interactive Model (WM2XXSI/WM2XXAUSI) workswith standard projectors and Windows® and Macintosh®computers. The Interactive Model will transform existingwhiteboards or other hard, flat surfaces, into interactivewhiteboards ...

Page 9 - Whiteboard Constraints; Figure 3; Projection

Installation Instructions 9 WM2XXSI/WM2XXAUSI Placement andProjection Area Constraints (See Figure 3) • There should be a minimum distance of 12 inchesbetween the base of the dual mount and the top of theprojection image. • The distance between the base of the dual mount andthe bottom corner of the ...

Page 10 - ELECTRICAL SHOCK HAZARD! CUTTING; Mounting Wall Bracket; Concrete or Concrete Block; Determine mounting location on wall.; Figure 4; Wood Studs; The wall to which the mount is being attached; Figure 6; Wood studs

Installation Instructions 10 INSTALLATION - (All Models) The WM2XXS/SI/AUS/AUSI short throw projector mounts canbe mounted to concrete, concrete block, wood studs or steelstuds. They can be mounted to 2" x 4" wood studs 16" apart. WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INT...

Page 11 - Figure 7; Steel Studs; See; Site Requirements; section before; Figure 8

Installation Instructions 11 5. Install four 5/16 x 2-1/2" hex head lag screws (L) throughfour 5/16" washers (M), holes of wall bracket and into drilledholes. (See Figure 7) Figure 7 Steel Studs IMPORTANT ! : See Site Requirements section before proceeding with Steel Studs installation to en...

Page 12 - Installation to Wall Bracket

Installation Instructions 12 10. Place wall bracket over anchors and align mounting holes in display mount with holes in anchors. (See Figure 12) 11. Insert 1/4-20 x 1-3/4" Phillips pan head screws (N) through 1/4" washer (Q), corresponding mounting hole on wallbracket and into anchor (P) an...

Page 13 - Projector Installation; UL Listed RPM Installation; or; raise

Installation Instructions 13 4. Loosen two bolts on either side of pitch adjustment screw.(See Figure 16) 5. Adjust pitch adjustment screw until mount is at desired pitchlevel. Turn clockwise to raise mounting level or turncounterclockwise to lower mounting level. (See Figure 16) 6. Tighten two bolt...

Page 14 - UL Listed RPA Installation; Installing Mount Covers; Complete the installation by; WM2XXSI/WM2XXAUSI Interactive; section or; WM2XXS/WM2XXAUS Standard

Installation Instructions 14 UL Listed RPA Installation 1. Line up mounting holes on RPA mount with correspondingholes on projector mounting plate. (See Figure 17) 2. Install four 1/4-20 x 3/8” Phillips pan machine screws (G)through RPA holes and into projector mounting plate. (SeeFigure 20) Figure ...

Page 15 - Be sure cables and cords are not pinched between; Removing Mount Covers

Installation Instructions 15 4. Lower the upper cover (X) onto the wall mount and lowercover, and fasten with two 8-32 x 3/8" Phillips pan headscrews (AB). (See Figure 24) NOTE: Be sure cables and cords are not pinched between upper and lower covers. Figure 24 Cable Management (Optional) In most...

Page 16 - Cables may be routed from below and up wall bracket; Routing Cables from Below (Steps 6 and 7); Proceed to Step 9; cable clips

Installation Instructions 16 NOTE: Cables may be routed from below and up wall bracket channel, or from above and down behind and into wallmount. • Routing Cables from Below (Steps 6 and 7) 6. Open cable clips along bottom edge of wall bracket. (SeeFigure 28) Figure 28 7. Thread cable up wall bracke...

Page 17 - Cables can be tied to inside of mount’s front; Installation of Wall Bracket Covers; If security screws are going to be used, use the security

Installation Instructions 17 10. (Optional) Cables can be tied to inside of mount’s front cover using cable ties (not included). Route cables nearfront cover and wrap cable tie through slots on front coverand around cables. (See Figure 32) Figure 32 11. Replace removed cable management covers (if ne...

Page 18 - Adjustments; Pitch Adjustment; Extension Adjustment; The mount covers need to be removed

Installation Instructions 18 Adjustments Pitch Adjustment IMPORTANT ! : The mount covers need to be removed before proceeding with pitch adjustment. NOTE: Remove mount covers from the mount following instructions in Removing Mount Covers section. 1. Loosen two 1/4-20 x 5/8" hex head cap screws (...

Page 19 - Wall Bracket Covers; (Projector arm not shown

Installation Instructions 19 Security Screw Installation (Optional) Wall Bracket Covers 1. Remove eight #8-32 x 1/2" Phillips pan machine screws (F)from wall bracket covers. (See Figure 40) Figure 40 2. Install eight #8-32 x 1/2" button head security screws (V)into holes in wall bracket cove...

Page 20 - Stop Bracket; For most projectors, it will be necessary to remove

Installation Instructions 20 4. Install two 8-32 x 3/8" button head security screws (AA) intolower cover. (See Figure 44) Figure 44 5. Replace upper cover and install two 8-32 x 3/8" button headsecurity screws (AA) into upper cover. (See Figure 45) Figure 45 Stop Bracket 1. Remove two bolts ...

Page 21 - Repeat Steps 2-3 for remaining three bolts; one bolt at a; Reinstall projector according to interface instructions.; WM2XXS/WM2XXAUS STANDARD MOUNT; Adapter plate

Installation Instructions 21 2. Remove one of four bolts from adapter plate. (See Figure 48) Figure 48 3. Install one 1/4-20 x 3/4" button head security screw (U) intohole (vacated by removed bolt in previous step) and intoplastic spacer. (See Figure 49) 4. Repeat Steps 2-3 for remaining three b...

Page 22 - Routing Cables from Below (Steps 5 and 6); Proceed to Step 8

Installation Instructions 22 Cable Management (Optional) In most cases, cable management covers will NOT need to beremoved in order to route cables from projector to the wallmount. But for some thick cables, removing the covers may benecessary. Removing Mount Covers 1. Remove and save two 8-32 x 1/2...

Page 23 - Cables

Installation Instructions 23 • Routing Cables from Above (Step 7) 7. Thread cables down through a surface mount cableaccessory (not included), then behind and into the wallbracket. (See Figure 57) Proceed to Step 8 Figure 57 8. Route cables through cover mount, projector arm tunneland into projector...

Page 24 - Remove mount covers from the mount following

Installation Instructions 24 Installation of Wall Bracket Covers NOTE: If security screws are going to be used, use the security screws (V) to install wall bracket covers. See Security Screw Installation section for details. 1. Place wall bracket top caps (C) over top of each wall bracketarm. (See F...

Page 26 - Mount Covers; Stop bracket

Installation Instructions 26 Mount Covers 1. Remove two #8-32 x 1/2" Phillips pan machine screws (F)holding mount covers on projector arm. (See Figure 69) 2. Install two #8-32 x 1/2" button head security screws (V) intoholes on mount cover. (See Figure 69) Figure 69 Stop Bracket 1. Remove tw...

Page 27 - Adapter Plate Bolts

Installation Instructions 27 Adapter Plate Bolts 1. Remove projector from short throw projector mountaccording to projector interface instructions. NOTE: For most projectors, it will be necessary to remove projector prior to installing four security screws toprojector bracket. For ease of installati...

Page 28 - Europe; Franklinstraat 14, 6003 DK Weert, Netherlands; Asia Pacific; 014 Milestone AV Technologies

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No. 918 on 9/F, Shatin Galleria18-24 Shan Mei Street...