Chief PNR Series - Manuals - manualsarea.com

Page 2 - DISCLAIMER

PNR Series Installation Instructions 2 DISCLAIMER Milestone AV Technologies and its affiliated corporations andsubsidiaries (collectively "Milestone"), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,c...

Page 3 - DIMENSIONS; Mount ing P atter n; PSBU INTERFACE BRACKET

Installation Instructions PNR Series 3 DIMENSIONS Mount ing P atter n 25 1.00 1.00 25 46 19.6 9 500 16.00 406 7.00 178 1.81 19.0 0 483 538 21.1 9 38 4 .18 1.50 .40 10 NOTE: PSBU INTERFACE BRACKET NOT SHOWN. THE PSBU INTERFACE BRACKET WILL ADD 1” IN DEPTHAND MAY AFFECT THE LOCATION OF THE DISPLAY ON ...

Page 5 - LEGEND

Installation Instructions PNR Series 5 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare i...

Page 6 - TOOLS REQUIRED FOR INSTALLATION

PNR Series Installation Instructions 6 TOOLS REQUIRED FOR INSTALLATION PARTS 7/32" (5.5mm) #2 9/16" A (1) [PNR assembly] B (2) [Cover] C (2) [End cap] D (2)[End cap] E (1)[Adjustment wrench] G (4) .850x.385x.135 J (12) 5-1/2" Cable tie F (1)[Adjustment insert] H (4) 5/16 x 2-1/2" K (...

Page 7 - Installing Mount to Wall; IMPROPER INSTALLATION CAN LEAD TO; Figure 1; Wood Studs

Installation Instructions PNR Series 7 Installing Mount to Wall WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONALINJURY OR DAMAGE TO EQUIPMENT! It is the installer’sresponsibility to make sure the structure to which the mountis being installed is capable of supporting...

Page 8 - Figure 3; Adjusting PNR Height; Figure 4; Installing Covers and End Caps; Figure 5

PNR Series Installation Instructions 8 6. Install two 5/16” x 2-1/2” lag bolts (H) and two.850x.385x.135” washers (G), through mounting holes inupper wall channel and into pilot holes. DO NOT tighten atthis time. (See Figure 3) 7. Place mount against wall aligning mounting holes in upperwall channel...

Page 9 - Mounting the Display; Figure 6

Installation Instructions PNR Series 9 Mounting the Display WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURYOR DAMAGE TO EQUIPMENT. Displays can weigh inexcess of 40 lbs (18.1kg). ALWAYS use two people andproper lifting techniques when installing display. 1. In...

Page 10 - Cable Management; Figure 8; Tension Adjustments; Vertical Tilt Tension Adjustment; Cable tie

PNR Series Installation Instructions 10 Cable Management WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TOEQUIPMENT! Make sure cables do not run through pinchpoints. 1. Thread cable ties (J) under cable clamps in mount arms.(See Figure 1) Figure 8 2. Route power/audio/v...

Page 11 - Swivel Tension Adjustment; Roll Tension Adjustment; Swing Arm Adjustments; Adjusting the Swing Arms Off-Center; Adjusting the Swing Arms Off Center

Installation Instructions PNR Series 11 Swivel Tension Adjustment CAUTION: DO NOT OVER TIGHTEN SWIVEL ADJUSTMENT NUT. Over tightening swivel adjustment nutwill cause excessive wear and may distort adjustmentcomponents. 1. Using a 9/16” wrench (not provided), slightly tighten orloosen swivel tension ...

Page 12 - Remove the display from the mount.

PNR Series Installation Instructions 12 Reconfiguring the Swing Arms to Left or Right ofCenter 1. Remove the display from the mount. WARNING: The next step will release the arm assembly from the mount. The arms and plate may fall if you are notcareful. 2. Remove four bolts (two on the top and two on...

Page 13 - Swing Arm Tension Adjustment

Installation Instructions PNR Series 13 Swing Arm Tension Adjustment Swing arm tension is pre-set at the factory and is adjusted toaccommodate displays with weights near the top of the mount’scapacity. If smaller displays are used it may be difficult to reposition thedisplay after mounting. NOTE: Th...

Page 14 - Removing Display from Mount; The pin may have been used as a more permanent

PNR Series Installation Instructions 14 Removing Display from Mount 1. Remove bolt or padlock from faceplate (if used). NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and movefrom the lower holes to the upper holes. 2. Pull back on flag on upper mounti...

Page 16 - Europe; Franklinstraat 14, 6003 DK Weert, Netherlands; Asia Pacific; PNR Series; 014 Milestone AV Technologies

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No. 918 on 9/F, Shatin Galleria18-24 Shan Mei Street...