Chief LCB1UP - Manuals - manualsarea.com

Page 2 - Installation Instructions; DISCLAIMER; The LCB1UP mounts are designed to be; OR; a UL Listed Chief CPA Series extension

LCB1UP Installation Instructions 2 DISCLAIMER Milestone AV Technologies and its affiliated corporations andsubsidiaries (collectively "Milestone"), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,condi...

Page 3 - DIMENSIONS

Installation Instructions LCB1UP 3 DIMENSIONS 18.38466.7 MAX MOUNTING PATTERN WIDTH 20.82 528.9 DIMENSIONS: INCHES [MILLIMETERS]

Page 4 - LEGEND

LCB1UP Installation Instructions 4 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fi...

Page 5 - TOOLS REQUIRED FOR INSTALLATION; M5

Installation Instructions LCB1UP 5 TOOLS REQUIRED FOR INSTALLATION PARTS #2 1/2" or 13mm 3/32" (included)1/8" (included)5/32" (included)M5 (included) C (6) E (6) [Interface Bracket Hardware Kit] A (8)M4x16mm B (6)M4x20mm M4x25mm D (6)M5x16mm M5x20mm F (6)M5x25mm G (6)M6x16mm H (6)M6x...

Page 6 - INSTALLATION; Attaching Mount to NPT Column; Figure 1; Attaching Mount to CPA Extension Column; Figure 3

LCB1UP Installation Instructions 6 INSTALLATION WARNING: FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CANRESULT IN SERIOUS PERSONAL INJURY OR DAMAGETO EQUIPMENT! It is the installer’s responsibility to makesure the structure to which this component is attached cansupport five t...

Page 7 - Figure 4; Attaching Interface Brackets to Display; Figure 5; The diamond-shape hole in the bracket corresponds to; Figure 6; IMPROPER INSTALLATION CAN LEAD TO

Installation Instructions LCB1UP 7 3. Install two 5/16" x 1" self-tapping screws (U) through two5/16" flat washers (V), bottom stop collar (BB), and intoinstalled column. 4. Install and tighten 5/16" x 3/4" set screw (X) into bottom stopcollar (BB). (See Figure 3) 5. Install and ...

Page 8 - Attaching Displays to Ceiling Mount; Figure 7; Adjustments; Always use two hands (one at bottom of; Roll

LCB1UP Installation Instructions 8 Attaching Displays to Ceiling Mount 1. Ensure that the latch mechanisms on interface brackets(FF) are already lowered. (See Figure 5) 2. While supporting both sides of display, lower display ontoceiling mount, hooking top of interface brackets onto front ofceiling ...

Page 9 - Tilt; Repeat for other mounting rail on opposite side of mount.; OPTIONAL

Installation Instructions LCB1UP 9 Tilt The ceiling mounts allow -5° to 20° tilt. The ceiling mount canbe locked at 0°, 5°, 10° and 15° tilt. 4. Loosen two tilt friction screws (located each side). (SeeFigure 10) 5. Adjust tilt as required. Note specific degrees of tilt. (SeeFigure 10) 6. Tighten tw...

Page 10 - Installing Covers; Be sure to line up tabs inside the bracket covers with

LCB1UP Installation Instructions 10 Installing Covers 1. Install two interface bracket covers (GG) over the top andbottom of each interface bracket. (See Figure 13) NOTE: Be sure to line up tabs inside the bracket covers with holes on sides of interface brackets. (See Figure 13) Figure 13 2. Install...

Page 12 - Europe; Franklinstraat 14, 6003 DK Weert, Netherlands; Asia Pacific; 013 Milestone AV Technologies, a

LCB1UP Installation Instructions USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No. 1 on 12/F, Shat...