Chief KSA-1020 - Manuals - manualsarea.com

Page 2 - Installation Instructions; DISCLAIMER

KSA-1020 Installation Instructions 2 DISCLAIMER Milestone AV Technologies, and its affiliated corporations andsubsidiaries, (collectively, Milestone) intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,conditions ...

Page 3 - DIMENSIONS

Installation Instructions KSA-1020 3 DIMENSIONS LEGEND CPU RANGE [0 - 191] 0" - 8.50" WIDTH OF CPU RANGE [248 - 457] .26 MOUNTING HOLES 7 1.46 MOUNTING SURFACE TO CPU SURFACE 37 -UNDER DESK MOUNTED CONFIGURATION *ONLY AVAILABLE WITH KSA-1020 PRODUCT **OPTION NOT AVAILABLE WITH KWT110 ALL IN ...

Page 4 - TOOLS REQUIRED FOR INSTALLATION

KSA-1020 Installation Instructions 4 TOOLS REQUIRED FOR INSTALLATION PARTS 7/64" #2 1/2" 17/64" 1/2" F (1) A (1) B (2) C (4) D (1) E (2) G (2) [Rubber edger--3"] 1/4-20 x 1-3/4" [CPU mount] 1/4-20" [Swivel bearing] 3/8 x 1-1/4" #12 x 2-1/2"

Page 5 - ASSEMBLY; Installation of Protective Rubber Edging; Figure 1; CPU Installation; Figure 2

Installation Instructions KSA-1020 5 ASSEMBLY Installation of Protective Rubber Edging 1. Place four strips of protective rubber edging (C) over thesharp edges located on the top and bottom of the mount (A).(See Figure 1) Figure 1 CPU Installation 1. Release bracket from mount by moving flag to open...

Page 6 - Figure 5; WALL MOUNT INSTALLATION; Site; Installing to Wood Studs

KSA-1020 Installation Instructions 6 5. Loosen adjustment knobs on top and bottom of the mountand slide flanges in order to allow for the CPU to be insertedfor mounting. (See Figure 5) NOTE: Top and bottom knobs can be removed and inserted into the front square holes in order to allow for largeCPU’s...

Page 7 - Figure 8; Installing CPU Mount to Wall

Installation Instructions KSA-1020 7 3. Drill two 7/64" diameter pilot holes at marked spots intowood stud. (See Figure 8) Figure 8 4. Install two #12 x 2-1/2" Phillips wood screws (G) throughbracket and drywall into wood stud. (See Figure 8) 5. Ensure bracket is vertical, then tighten screw...

Page 8 - Site Requirements for Using Steel Studs; Figure 9

KSA-1020 Installation Instructions 8 Site Requirements for Using Steel Studs WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto asteel stud s...

Page 9 - Installing to Steel Studs or Drywall

Installation Instructions KSA-1020 9 Installing to Steel Studs or Drywall WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONALINJURY OR DAMAGE TO EQUIPMENT! 1. Determine location for mount keeping in mind CPU size andsafety requirements. 2. Use the removed mounting b...

Page 11 - Installing Mount to Desk; Installing to

Installation Instructions KSA-1020 11 Installing Mount to Desk WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury ordamage to equipment! It is the installer’s responsibility tomake sure the desk to which this component is attached cansup...

Page 12 - Europe; Asia Pacific

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No. 1 on 12/F, Shatin Galleria18-24 Shan Mei Street ...