Central Pneumatic 97053 - Manuals

Page 2 - DANgER; Notice; CAuTION

Page 2 SKU 97053 For technical questions, please call 1-800-444-3353. SAVE THIS MANuAL Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram...

Page 3 - gENERAL SAFETY RuLES; Keep work area clean and well lit.

Page 3 SKU 97053 For technical questions, please call 1-800-444-3353. gENERAL SAFETY RuLES WARNINg! Read all instructions Failure to follow all instructions listed below may result in serious injury. The term “power tool” in all of the warnings listed below refers to your 5” Palm Orbital Wet Sander....

Page 4 - Service; This will ensure that the safety of the power tool is; VIBRATION HAzARD; and shoulders. To reduce the risk of vibration-related injury:

Page 4 SKU 97053 For technical questions, please call 1-800-444-3353. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children, and do not allow people d. unfamiliar with the Sander or these instructions to operate t...

Page 5 - abnormal vibration occurs, stop use immediately.; SPECIFIC SAFETY RuLES; . Never operate the

Page 5 SKU 97053 For technical questions, please call 1-800-444-3353. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool 6. do the work.To reduce vibration, maintain the tool as explained in this manual. If any 7. abnormal vibration occurs, stop use immediately. ...

Page 6 - SAVE THESE INSTRuCTIONS.; SPECIFICATIONS

Page 6 SKU 97053 For technical questions, please call 1-800-444-3353. Use clamps (not included) or other practical ways to secure and support the 13. workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.This product is not a toy. K...

Page 7 - uNPACKINg; cover of this manual as soon as possible.; SET uP INSTRuCTIONS; to the Assembly Diagram near the end of this manual.; Assembly; Then firmly screw on the Quick Connector.; WARNINg; water filter as shown in the illustration on the next page.

Page 7 SKU 97053 For technical questions, please call 1-800-444-3353. uNPACKINg When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SET uP I...

Page 8 - FIguRE B; Attach the; ” diameter; Sand Paper Disc to the Sander’s Pad (38) by pressing it; FIguRE C; Use only cold, clean water. Never run the Wet Sander; FIguRE D

Page 8 SKU 97053 For technical questions, please call 1-800-444-3353. TO SANDER OILER FILTER REguLATOR AIR COMPRESSOR FIguRE B Attach the 3. 5” diameter Sand Paper Disc to the Sander’s Pad (38) by pressing it onto the pad. (See Figure C.) 5” DIAMETER SAND PAPER DISC PAD (38) FIguRE C Place the Sande...

Page 9 - OPERATINg INSTRuCTIONS; Prior to using the Sander, make sure to wear ANSI-approved

Page 9 SKU 97053 For technical questions, please call 1-800-444-3353. Connect a compressed air supply hose (not included) to the previously installed 5. Quick Connector. Then turn on the air compressor, and set its regulator to 90 PSI . Do not exceed 90 PSI. (See Figure E.) OPERATINg INSTRuCTIONS Re...

Page 10 - MAINTENANCE AND SERVICINg; Risk of serious personal injury from accidental starting.; inspect the general condition of the Sander. Check for

Page 10 SKU 97053 For technical questions, please call 1-800-444-3353. To adjust the water flow rate of the Sander, turn the Water Flow Control located 5. on the Anchor Assembly (43). (See Figure D.) Sand the workpiece evenly with gentle, broad, sweeping strokes in a criss-cross 6. pattern.During th...

Page 11 - TROuBLESHOOTINg; Problem

Page 11 SKU 97053 For technical questions, please call 1-800-444-3353. AFTER uSE, 4. clean external surfaces of the tool with a clean, moist cloth. CAuTION! 5. All maintenance, service, and repairs not mentioned in this manual must only be performed by a qualified service technician. TROuBLESHOOTINg...

Page 12 - PARTS LIST

Page 12 SKU 97053 For technical questions, please call 1-800-444-3353. Part Description Qty. Part Description Qty. 1 Valve Lever 1 25 O-Ring (4 x 7) 1 2 Spring Pin (3 x 32) 1 26 Valve Pin 1 3 Screw (M5 x 35) 4 27 Valve Spring 1 4 Top Cover 1 28 Body 1 5 Body Packing 1 29 Regulator Set 1 Set 6 Screw ...

Page 13 - ASSEMBLY DIAgRAM

Page 13 SKU 97053 For technical questions, please call 1-800-444-3353. ASSEMBLY DIAgRAM 3 46 4 5 67 8 9 10 11 12 13 13-1 14 15 16 17 8 13-1 13-2 1 2 18 47 19 20 21 22 232425 26 27 29 35 34 28 31 32 33 30 37 36 39 40 48 41 42 45 43 44 38

Page 14 - LIMITED 1 YEAR WARRANTY; THIS; Record; available individually as replacement parts.; PLEASE READ THE FOLLOWINg CAREFuLLY

Page 14 SKU 97053 For technical questions, please call 1-800-444-3353. LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in material...