Central Pneumatic 95173 - Manuals

Page 2 - sPEcIfIcATIOns; Operating Air Pressure; sAVE THIs MAnUAl; UnPAcKIng

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 2 sPEcIfIcATIOns Rivet Capacity (Pin Diameter) 3/32”, 1/8”, 5/32”, 3/16” Operating Air Pressure 85 to 90 PSI Air Consumption 4.5 SCFM @ 90 PSI Air Inlet Size 1/4”-18 NPT Overall Dimensions 11” High x 10-1/8” Long x 4” Wide Weight ~3 ...

Page 5 - AssEMbly InsTRUcTIOns; fIgURE A; If an automatic oiler is not used, put 3-5 drops of; fIgURE b; Air Filter

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 5 AssEMbly InsTRUcTIOns REgUlATOR fIgURE A fIlTER OIlER For best service, you should incorporate an oiler, regulator, and in-line filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all availab...

Page 6 - OPERATIOn; fIgURE d; When drilling rivet holes in a workpiece, make sure to use the same; do not exceed 90

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 6 OPERATIOn bOTTlE (15) TRIggER (25) nOsEPIEcE (1) OUTER cylIndER (2) AIR sUPPly HOsE (nOT InclUdEd) fIgURE d Make sure the Bottle (15) is firmly inserted onto the Airproof Lid (16) of the Riveter. (see figure d.) Depending on the si...

Page 7 - Always wear ANSI-approved safety impact goggles when perform-; To clean the exterior of the Riveter,; wipe with a clean, damp cloth using a mild; To clean and change the jaws:; fIgURE E

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 7 InsPEcTIOn, MAInTEnAncE, And clEAnIng wARnIng! Always wear ANSI-approved safety impact goggles when perform- ing any inspection, maintenance, or cleaning procedures. wARnIng! Prior to performing any inspection, maintenance, or clea...

Page 8 - The Riveter comes from the factory with hydraulic oil included.; always store the Riveter in a clean, dry, safe location out of reach; PlEAsE REAd THE fOllOwIng cAREfUlly

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 8 The Riveter comes from the factory with hydraulic oil included. Over time, if the performance of the tool deteriorates it may be due to low hydraulic oil. Have a qualified technician replenish the oil in the reservoir by removing t...

Page 9 - TROUblEsHOOTIng; PARTs lIsT

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 9 TROUblEsHOOTIng Problem Possible cause Possible solution Jaws slipping. Worn or damaged Jaws. Replace Jaws. Jaws will not open. Loose Nosepiece.Dirty Jaws. 1.2. Tighten Nosepiece.Clean Jaws. 1.2. Stroke is too short. Low oil.Rivet ...

Page 10 - AssEMbly dIAgRAM

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 10 AssEMbly dIAgRAM nOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 35

Page 11 - wARRAnTy; LImITed 1 yeAr

SKU 95173 for technical questions, please call 1-800-444-3353 PAGE 11 wARRAnTy 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original...