Central Pneumatic 95014 - Manuals

Page 2 - listed on pages; SAFETY WARnIngS AnD PREcAUTIOnS; Keep work area clean.; atmospheres, such as in the presence of flammable liquids, gases, or

PRODUcT SPEcIFIcATIOnS SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 2 SAVE ThIS MAnUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice wit...

Page 4 - regularly only by a qualified technician.; Maintain a firm grip on the Blast Gun when in use.

SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 4 15. Replacement parts and accessories. This product is to be repaired and serviced only by a qualified technician. When this product is serviced, only identical replacement parts should be used. Use of any other parts will void the...

Page 6 - SAVE ThESE InSTRUcTIOnS

6. Use respiratory protection when source controls cannot keep silica exposures below the recommended levels. 7. Provide periodic medical examinations for all workers who may be exposed to crystalline silica. 8. Post signs to warn workers about the hazard and to inform them about required protective...

Page 7 - PAGE 7; ASSEMBLY InSTRUcTIOnS; To Attach The Handle Bars:; “Left”; and; “Right”; . Align the holes in the left; FIgURE B; To Attach The Wheels And Front Foot:

SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 7 ASSEMBLY InSTRUcTIOnS To Attach The Handle Bars: 1. To attach the two Handle Bars (6) to the Tank (1), lay the Tank on a flat, level surface with its Handle Bar mounting brackets facing up. (See Figure B.) 2. The Handle Bars (6) ar...

Page 8 - FIgURE c

SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 8 3. Slide a Wheel Washer (51) onto each end of the Wheel Axle (5). (See Figure B.) 4. Place a Wheel (2) onto each end of the Wheel Axle (5). Then, slide a Wheel Washer (51) onto each end of the Wheel Axle. (See Figure B.) 5. Insert ...

Page 9 - OPERATIng InSTRUcTIOnS; media; “OFF”; If this is a large job, fill the Tank only 3/4 full and reload as needed

5. Slide the other end of the Abrasive Hose (24) onto the Abrasive Outlet Manifold (22). Then firmly tighten the Hose Clamp (23). (See Figure c.) OPERATIng InSTRUcTIOnS Abrasive Selection: 1. The type of media chosen will greatly influence the amount of time needed to clean a particular surface area...

Page 10 - FIgURE D; FIgURE E

7. IMPORTAnT TIP: If the humidity is 90 to 100%, the Water Trap (17) will not be able to trap all of the moisture in a 3/4 full Tank (1). It is recommended to reduce the amount of media, load more frequently, and empty the Water Trap more often. This will reduce the possibility of clogging the botto...

Page 11 - air compressor, and set its regulator between; “On”; Grip the Blast Gun firmly with both hands.; FIgURE F

3. Connect the air compressor’s hose to the Inlet Connector (19). Then turn on the air compressor, and set its regulator between 65 to 125 PSI. Do not exceed 125 PSI. (See Figure F.) 4. Turn the Air Supply Valve (18) and Throttling Valve (18A) to the “On” position. At this point, the Tank (1) will b...

Page 13 - PLEASE READ ThE FOLLOWIng cAREFULLY; manual must only be performed by a qualified service technician.

SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 13 PLEASE READ ThE FOLLOWIng cAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR ...

Page 14 - PAGE 14; TROUBLEShOOTIng

SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 14 TROUBLEShOOTIng

Page 15 - PARTS LIST & ASSEMBLY DIAgRAM - AIR BLASTER; PAGE 15

PARTS LIST & ASSEMBLY DIAgRAM - AIR BLASTER SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 15 30 30A 29 Part # Description QTY Part # Description QTY 1 Tank 1 17 Water Trap 1 2 Wheel 2 18 Air Supply Valve (3/8”) 1 3 Cotter Pin 3 18A Throttling Valve (3/8”) 1 4 Front Foot 1 18...

Page 16 - PAGE 16; PARTS LIST & ASSEMBLY DIAgRAM - BLAST gUn

SKU 95014 For technical questions, please call 1-800-444-3353 PAGE 16 PARTS LIST & ASSEMBLY DIAgRAM - BLAST gUn 42c 43c 48c 46c 47c 45c 39c 38c 37c 36c 35c 40c 32c 33c 49c 34c 31c 41c 44c nOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as ...

Page 17 - LIMITED 90 DAY WARRAnTY; of exclusion may not apply to you.; ThIS WARRAnTY IS ExPRESSLY In LIEU OF ALL; which vary from state to state.

LIMITED 90 DAY WARRAnTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. ...