Central Pneumatic 90342 - Manuals

Page 2 - powered tools in the presence of flammable gases or liquids.

Page 2 SKU 90342 Specifications Recommended Air Pressure 85 - 115 PSI Maximum Air Pressure 115 PSI Air Inlet 1/4” - 18 NPT Nail Capacity 3/4” to 2-1/2” T Nails Magazine Capacity 80 (Side Load) Air Consumption 7.4 CFM Includes: Coupler Plug, 3 Hex Keys, Tool Oil, OSHA Approved Goggles, Replacement na...

Page 3 - Do not operate tool is under the influence of alcohol or drugs; . If an extension cord is required, it must

Page 3 SKU 90342 Do not overreach . Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. Maintain tools with care . Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords ...

Page 4 - SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS; a nail from being accidentally fired during connection.

Page 4 SKU 90342 SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS Important consumer information: This Nailer is equipped with a contact trip Trigger. This Trigger mechanism is designed primarily for high volume work where exact placement of the nail is not critical. By holding the Trigger, the Nailer will...

Page 5 - The nails can ricochet, causing personal injury.; Do not drive nails close to the edge of a workpiece.; The workpiece is likely to; Unpacking; manual as soon as possible.

Page 5 SKU 90342 Do not drive nails on top of other nails, or with the tool at too steep an angle. The nails can ricochet, causing personal injury. Do not drive nails close to the edge of a workpiece. The workpiece is likely to split, allowing the nail to fly free or ricochet and cause personal inju...

Page 6 - Page; Air Connection Setup; tape before threading it into the

Page SKU 90342 Air Connection Setup Concrete Nailer 1/4”-18 NPT For best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. You will need to prepare a 1/4” c...

Page 7 - Operation; Nailer Specific Warnings!

Page 7 SKU 90342 Operation Loading Nails Refer to FIGURES 1 and 2 on pages 5 and . Nailer Specific Warnings! Warning! Disconnect the Nailer from the air compressor whenever loading or servicing. After disconnecting the Nailer from the air compressor, there could still be enough air pressure to fire ...

Page 8 - of the nailer. Give the trigger a quick pull and release.

Page 8 SKU 90342 Movable Magazine (#53) Operating the Concrete Nailer 1. With the tool disconnected from the air supply, load nails as explained on page 5. Then, connect the Concrete Nailer to the air supply. 2. Before using the Nailer each time, check the driving depth by firing a nail into a scrap...

Page 9 - Worn or dirty bumper, damaged pusher spring, inadequate air flow,; to make sure all of the air is expended.; Maintenance; not deep enough, take the Nailer to a qualified service technician.

Page 9 SKU 90342 Troubleshooting Warning! If you detect any air leaks, power loss, the Nailer skips driving, drives too deep, or not deep enough, take the Nailer to an qualified service technician for repair. Note: Have the following problems repaired by a qualified service technician. Problem : Air...

Page 10 - Parts List

Page 10 SKU 90342 NOTE : Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE...

Page 11 - Assembly Drawing

Page 11 SKU 90342 Assembly Drawing 1 2 3 4 5 7 8 9 10 11 12 13 14 15 1 17 18 19 20 21 22 23 24 25 2 27 7 28 29 7 28 30 2 31 32 33 34 31 35 3 30 37 33 38 39 40 39 41 54 55 5 57 7 58 42 43 44 45 4 47 48 45 40 49 50 51 5 2 53 52 59 0 1 2 3 7 8 9 4 5 0 70 71 72 Coupler Plug (#73) Not shown.

Page 12 - LIMITED 1 YEAR WARRANTY; MERCHANTABILITY AND FITNESS.

Page 12 SKU 90342 LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the...