Buhler 740, 840, 840G - Manuals

Page 3 - Parts

740, 840 & 840G Snowblowers TABLE OF CONTENTS DESCRIPTION PAGE Warranty ...................................................................... 1 Safety Instructions & Safety Sign Locations ................ 2 Operating Instructions .................................................. 3 Assembly...

Page 4 - WARRANTY POLICY; Any labor subject to warranty; must; be authorized by Buhler Manufacturing. The labor rate for; GOVERNMENT LEGISLATION:; This warranty does not apply to rentals

740, 840 & 840G Snowblowers 1 WARRANTY POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months (90 days for commercial application) from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agric...

Page 5 - SNOWBLOWER; WHEN ORDERING PARTS

740, 840 & 840G Snowblowers 2 SNOWBLOWER This manual is for model #740 & #840 snowblowers with an open gear gearbox and for model #840G snowblower, which has a sealed oil bath gearbox. When ordering parts, specify model number and serial number. The snowblower is the push type and will mount...

Page 7 - OPERATING INSTRUCTIONS – cont’d; Always stop blower for servicing or unplugging. The PTO

740, 840 & 840G Snowblowers 4 OPERATING INSTRUCTIONS – cont’d . 9. Periodically check all bolts for tightness. The bolt holding on the fan and the bearing bolts are of particular importance. 10. Danger: Always stop blower for servicing or unplugging. The PTO should be disengaged before dismounti...

Page 8 - ASSEMBLY INSTRUCTIONS

740, 840 & 840G Snowblowers 5 ASSEMBLY INSTRUCTIONS 1. #740: Turn the bottom tube weldments (#9) as shown in drawing and slide them into the sleeve welded to the main body. #840 & #840G: Turn the bottom tubes (#93) as shown in drawing and slide them into the sleeve welded to the main body. A...

Page 9 - ASSEMBLY INSTRUCTIONS – cont’d.; available as an option.

740, 840 & 840G Snowblowers 6 ASSEMBLY INSTRUCTIONS – cont’d. 5. Hydraulic spout swivel: a) Mount the swivel arm (#60) onto the swivel pin welded to the back corner of the fan housing using a 1" I.D. washer (#29) and a 3/16" x 1 ½” cotter pin (#62). b) Wrap cable (#61) around spout and c...

Page 10 - Do not run the

740, 840 & 840G Snowblowers 7 ASSEMBLY INSTRUCTIONS – cont’d. 8. PTO Shield: All snowblowers are supplied with a PTO shield. Bolt the shield (#74) to the hinges on the top of the gearbox on both the #740 and #840 snowblowers using ¼” x ½” hex bolts, lock washers and hex nuts. Insert a 3/16" ...

Page 21 - Description

740, 840 & 840G Snowblowers 18 SNOWBLOWER PTO (STANDARD) Item # Part # Description F842 Shaft Complete 936263 Tractor Half of PTO (Shear) 936264 Implement Half of PTO (Clamp Yoke) 1 936277 Shear Assembly 2 936199 Safety Slide Lock Repair Kit (Collar, Spring, Ret. Ring, 2-Pawls) 3 936249 Shear As...

Page 25 - NOTES

Page 28 - DIVISION LOCATIONS; CANADIAN WAREHOUSES; Buhler Manufacturing

DIVISION LOCATIONS U.S. WAREHOUSES Farm King Division 301 Mountain Street S. Morden, MB R6M 1X7 Ph.: (204) 822-4467 Fax: (204) 822-6348 Allied/Inland Division 1260 Clarence Avenue Winnipeg, MB R3T 1T2 Ph.: (204) 284-6100 Fax: (204) 477-2325 B.I.I. Division 1330 43 rd Street N.W. Fargo, ND 58102 Ph: ...