Buhler 2895E - Manuals - manualsarea.com

Page 2 - PRINTED IN CANADA; WARRANTY REGISTRATION AND POLICY; Any labor subject to warranty; must; be authorized by Buhler Manufacturing. The labor

PRINTED IN CANADA WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications....

Page 3 - bühler; Allied Front-End Loader; 895E OPERATOR’S AND PARTS MANUAL; Table of Contents

bühler Allied Front-End Loader - 1 - P4493 2895E OPERATOR’S AND PARTS MANUAL Table of Contents Description Page Registration and Policy Loader Specifications .......................................................................................... 2 Introduction Terminology ...........................

Page 4 - LOADER SPECIFICATIONS

bühler Allied Front-End Loader - 2 - P4493 LOADER SPECIFICATIONS Illustration (TSL shown)

Page 5 - Specification Chart

bühler Allied Front-End Loader - 3 - P4493 Specification Chart Item Description 2895E REG 2895E TSL 2895E S REG 2895E S TSL A Maximum lift height to pivot pin [in/cm] 181/460 181/460 169/429 169/429 B Maximum lift height under level bucket [in/cm] 172/437 172/437 160/406 160/406 C Clearance with buc...

Page 6 - INTRODUCTION; tractor manual

bühler Allied Front-End Loader - 4 - P4493 INTRODUCTION This manual has been provided as information regarding the specifications, safe operation and maintenance of your agricultural front-end loader. Read and understand this manual and the tractor manual prior to operating to obtain the best use of...

Page 7 - Serial Decal Location:; The serial decal is located on the inside left arm of the loader; Serial Number; The; Buhler Manufacturing

bühler Allied Front-End Loader - 5 - P4493 Serial Decal Location: The serial decal is located on the inside left arm of the loader joint plate. Please record the serial number in the space provided for future reference. The serial decal will provide the model and date of manufacture of the loader an...

Page 8 - SAFETY; Operate the loader while seated in the tractor seat only.

bühler Allied Front-End Loader - 6 - P4493 SAFETY Read and understand all the safety messages listed in this manual. For your safety and the safety of others near the machine, learn how to control and operate the loader properly. It is your responsibility to inform subsequent operators and owners of...

Page 9 - Important Precautions:; The alert symbol is used throughout this manual. It indicates; CAUTION; injury. It may also be used to alert against unsafe practices.

bühler Allied Front-End Loader - 7 - P4493 Safety Decals: Safety Decal Location illustrates the approximate location and detail of safety decals. To install safety decals ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the small...

Page 12 - PRE – OPERATION; Tractor Manual; Tractor Manual

bühler Allied Front-End Loader - 10 - P4493 PRE – OPERATION WARNING The tractor must be equipped with an approved Roll over Protection Structure (ROPS) and safety belts to help prevent personal injury or death caused by tractor roll over. CAUTION Maximum rated loader capacity may exceed tractor rati...

Page 13 - OPERATION; The following section provides general

bühler Allied Front-End Loader - 11 - P4493 OPERATION General Operating Notes: The following section provides general information that can be applied towards your specific application. Ensure that you’ve read and understood this manual and your Tractor Manual . Observe all safety precautions and fol...

Page 14 - Lower and dump heavy loads slowly by feathering.

bühler Allied Front-End Loader - 12 - P4493 All Buhler - Allied hydraulic valves are self-centering and return to neutral from all positions except float. The float or detent spool is only to be used on the boom circuit. This position allows the oil to freely flow through the valve so the lift cylin...

Page 15 - Carry the load no; Backfilling or Scraping:; Use leveling rod for a guide to

bühler Allied Front-End Loader - 13 - P4493 Minimize turning angle and length of run between pile and trailer to increase loading efficiency. Also, place load evenly or centered in the attachment. WARNING Carry the load no higher than necessary to clear the terrain. Turn and brake slowly. Always be ...

Page 17 - Handling bales and pallets:; Do not operate A – Frame for bales without the stabilizers.

bühler Allied Front-End Loader - 15 - P4493 Handling bales and pallets: For safe handling of bales and pallets please follow procedures below: WARNING Do not operate A – Frame for bales without the stabilizers. With a single spear, enter one of the ends of the bale and drive the spear horizontally i...

Page 18 - The TSL loader is highly

bühler Allied Front-End Loader - 16 - P4493 When loading bales onto a trailer, park trailer in close proximity to minimize turning angle and length of travel to increase loading efficiency. As you lift the bale using the regular loader, it is recommended to feather the valve to allow bucket cylinder...

Page 20 - INSTALLING / REMOVING LOADER; Prior to initial mounting, cycle loader cylinders to; Verify front and side clearances during installation to

bühler Allied Front-End Loader - 18 - P4493 INSTALLING / REMOVING LOADER Installing: CAUTION Prior to initial mounting, cycle loader cylinders to displace air. This ensures the loader will remain in the storage position and operate consistently. 1. Position the tractor centrally and parallel to the ...

Page 21 - Shut tractor off and store parking stands within loader; A bucket or other suitable attachment must be attached

bühler Allied Front-End Loader - 19 - P4493 5. With the tractor in neutral, continue to retract the lift cylinders and extend the bucket cylinders to rotate the upright back against the lock pin stops. Shut the tractor off and set park brake. 6. Install both upright attachment pins and secure with h...

Page 22 - Operate hydraulic controls slowly. Loader will

bühler Allied Front-End Loader - 20 - P4493 2. Lower attachment level to the ground while engaging float position. Ensure attachment rests firmly on ground with minimal downward pressure. If required extend bucket cylinders to rotate upright rearward. At this stage the pin should have no pressure. S...

Page 23 - INSTALLING / REMOVING LOADER ATTACHMENTS

bühler Allied Front-End Loader - 21 - P4493 INSTALLING / REMOVING LOADER ATTACHMENTS Installing: 1. Position tractor centrally within the bucket hooks. Dump Quick-tach slightly from vertical position. Slowly drive the tractor forward until the Quick-tach contacts the bucket. 2. Slowly raise the load...

Page 24 - LUBRICATION; Ensure that grease fittings accept grease. Should any fitting

bühler Allied Front-End Loader - 22 - P4493 LUBRICATION Lubricate loader bushings and pivots every eight hours of average operation with high-grade grease. For grease fitting locations see illustration below. Select grease based on the expected outside temperature range. Lithium, Molybdenum and synt...

Page 25 - MAINTENANCE; Hydraulic Lift Lock Instructions Decal; Hydraulic Lift Lock:

bühler Allied Front-End Loader - 23 - P4493 MAINTENANCE General Inspection: CAUTION Lower attachment and loader to ground, place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing loader. WARNING Relieve hydraulic pres...

Page 27 - Escaping fluid under pressure can; Never operate the loader with frayed or damaged hoses

bühler Allied Front-End Loader - 25 - P4493 Hydraulics: WARNING Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Before repairing, adjusting, or disconnecting lines, be sure to relieve all pressure. Before applying pressure to the system...

Page 28 - Shut tractor down and relieve oil pressure in system by; Never use grease to lubricate valve components where

bühler Allied Front-End Loader - 26 - P4493 A yearly inspection of the valve is recommended. However the maintenance intervals on the valve depends on the surrounding environment or if valve spools become stiff. Where temperatures fluctuate from one extreme to another or exposed to high salt the int...

Page 30 - TSL GENERAL NOTE AND INSTRUCTIONS; true self leveling system; If the loader is raised with the; oil from the bucket piston side will be bypassed at; If the loader is lowered with the bucket; oil from the bucket shaft side will be bypassed at high

bühler Allied Front-End Loader - 28 - P4493 TSL GENERAL NOTE AND INSTRUCTIONS 1. The true self leveling system (TSL) utilizes mechanical linkages to maintain bucket level while raising and lowering. The pivot plate weldment, leveling tubes and linkages have been developed to ensure that the bucket r...

Page 31 - TROUBLE SHOOTING; Problem

bühler Allied Front-End Loader - 29 - P4493 TROUBLE SHOOTING Possible Cause Quick couplers leaking Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking. Control valve does not shift properly. Air in hydraulic system. Cylinder leaks internally. Faulty valve...

Page 32 - Trouble Shooting Continued; Possible Cause

bühler Allied Front-End Loader - 30 - P4493 Trouble Shooting Continued Problem Insufficient lift capacity. Slow leak down. Excessive wear on bottom of bucket and wear pads. Hydraulic cylinders inoperative. Pump operating continually on closed center tractor hydraulics system. Loader lift and bucket ...

Page 33 - PARTS APPENDIX; Description Page

bühler Allied Front-End Loader P4493 - 31 - 2895E & 2895E S PARTS APPENDIX Description Page 2895E & 2895E S Main Frame Assembly .............................................................................. 32 Hydraulic Plumbing ..................................................................

Page 34 - Main Frame Assembly

bühler Allied Front-End Loader P4493 - 32 - 2895E & 2895E S Main Frame Assembly 5

Page 35 - Description

bühler Allied Front-End Loader P4493 - 33 - 2895E & 2895E S Main Frame Assembly Item Part No. Description 2895E 2895E S 1 24966 2895 Main Frame Weldment (113579, 113633 included) 1 - 1 24944 2895 S Main Frame Weldment (bushings included) - 1 2 25388 2895 Euro Quick Attach Weldment 1 1 3 Ref. Lif...

Page 36 - Hydraulic Plumbing Assembly

bühler Allied Front-End Loader P4493 - 34 - 2895E & 2895E S Hydraulic Plumbing Assembly

Page 39 - Main

bühler Allied Front-End Loader P4493 - 37 - 895E TSL & 2895E S TSL Main Frame Assembly Item Part No. Description 2895E TSL 2895E S TSL 1 24967 2895 TSL Main Frame Weldment (bushings incl.) 1 - 1 24945 2895 S TSL Main Frame Weldment(bushings incl.) - 1 2 25388 2895 Euro Quick Attach Weldment 1 1 ...

Page 40 - Loader

bühler Allied Front-End Loader P4493 - 38 - 2895E TSL & 2895E S TSL Hydraulic Plumbing Assembly 4 3 15 13 7 B B A 12 VIEW A-A 3 4 9 10 11 14 6 17 13 16 5 2

Page 43 - Maximum pressure – 3000 psi

bühler Allied Front-End Loader P4493 - 41 - 2895E Cylinder Assembly NOTES:1. Bucket cylinder shown 2. All cylinder seals are contained in corresponding seal kit. 3. Refer to page 44 for prevailing torque for locknuts. CAUTION Maximum pressure – 3000 psi Bucket Cylinders Lift Cylinders Regular & ...

Page 44 - Hydraulic Fitting Torques:

bühler Allied Front-End Loader P4493 - 42 - Hydraulic Fitting Torques: (ft-lbs) (NM) (ft-lbs) (NM) -04 7/16-20 14-16 20-22 10-11 13-15 -05 1/2-20 18-20 24-27 13-15 18-20 -06 9/16-18 24-26 33-35 17-19 23-26 -08 3/4-16 50-60 68-78 34-38 47-52 -10 7/8-14 72-80 98-110 50-56 69-76 -12 1-1/16-12 125-135 1...

Page 46 - a partnership”; CANADIAN WAREHOUSES

Buhler Manufacturing “ a partnership” Customer Support: 1-888-524-1003 1260 Clarence Ave. Box 7300 Winnipeg, MB. R3C 4E8 Ph.: (204) 661-8711 Fax: (204) 654-2503 www.buhler.com Printed in Canada Allied Division 1201 Regent Ave. W. Box 1003 Winnipeg, MB R2C 3B2 Ph.: (204) 661-8712 Fax: (204) 654-4331 ...