Bryston 14B SST - Manuals - manualsarea.com

Page 2 - 4B SST Series Amplifier; Table of Contents; Back Cover

14B SST Series Amplifier Table of Contents General Introduction Page 1 DescriptionInstallation and Ventilation Rear Panel Input Settings/Connections Page 2 Setting Input Selector SwitchBalance Input Connector ConfigurationSetting Input Sensitivity Output Binding Posts Page 3 Front Panel Description ...

Page 3 - Thank you for choosing the; 4B SST SERIES Stereo Power Amplifier; The

14B SST Series Amplifier 1 Introduction Thank you for choosing the 14B SST SERIES Stereo Power Amplifier . Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. We consideryou, our customer, to be Bryston’s most important resource, and your opinion is ...

Page 4 - Rear Panel Input / Output Connections; Input Sensitivity Selection.; This input connector; accepts standard ‘RCA’ or ‘Phono’ connectors.; gold plated; Balanced input Vs Single ended input:; RCA PLUG

14B SST Series Amplifier 2 Rear Panel Input / Output Connections 1. Input Select Switch. Each SST channel gives the user the option of switching between either balanced input or single ended input. Input Sensitivity Selection. The optimum gain setting will depend upon the source pre-amp operating le...

Page 5 - RED; in-phase amplifier output; BLUE; inverted-phase amplifier output; coin; Coin

14B SST Series Amplifier 3 5. Output binding posts. The RED binding post is the in-phase amplifier output . Connect to this post the (+) terminal on the loudspeaker. The BLUE binding post is the inverted-phase amplifier output . Connect to this post the (-) terminal on the loudspeaker. Note: At no t...

Page 6 - Front Panel; indicates the amplifier has no power.

14B SST Series Amplifier 4 Front Panel 1. 'SST POWER' switch The front panel label 'SST POWER', is a touch sensitive membrane switch used to apply or remove a/c line power to thesoft start circuitry. Push firmly the center of the switch until the power-up sequence begins. Push again and the amplifie...

Page 7 - Power Control; fig W

14B SST Series Amplifier 5 Power Control 1. Master circuit - breaker. The 14B SST amplifier uses a magnetic-trip circuit breaker (1) to protect the amplifier. This switch should be ‘OFF’ during installation. When switched ‘OFF’all A/C power is removed from the amplifier, including standby power.The ...

Page 9 - Typical Band-pass Noise

14B SST Series Amplifier 7 Typical Band-pass Noise Typical THD+N Harmonic Content Power supply artifacts are all below -95 dBu BAL+6db input shown The harmonic content of the 14B SST is all even order. dBu: dB relative to a reference of 0.7746 Volts

Page 11 - Typical IMD Sweep

Typical THD+N Sweep 4 ohm 900w 8 ohm 600w 14B SST Series Amplifier 9 Typical IMD Sweep 8 ohm 600w 4 ohm 900w Graph shows that distortion isessentially unaffected by load.BAL+6db input shown.

Page 12 - Damping Factor

10 Damping Factor 8 ohm reference 14B SST Series Amplifier

Page 13 - > 60 volts per microsecond

14B SST Series Amplifier 11 Technical Specifications Power Output 600 watts per channel into 8 ohms 900 watts per channel into 4 ohms Gain Select and Sensitivity 29dB - 2.5Vin = 600W @ 8 Ohms - (Unbalanced position)29dB - 2.5Vin = 600W @ 8 Ohms - (Balanced +6db position) 23dB - 5.0Vin = 600W @ 8 Ohm...

Page 14 - BRYSTON 20 -YEAR WARRANTY

BRYSTON 20 -YEAR WARRANTY Bryston products are warranted to be free frommanufacturing defects for a minimum of twentyyears from the original date of manufacture. Thisincludes parts, labour and return shipping to thefirst owner and all subsequent owners. Warrantycoverage is automatic and commences wi...