Bryant T6--PHP - Manuals - manualsarea.com

Page 3 - INTRODUCTION; settings

3 INTRODUCTION Bryant’s 7--day, 5/2--day, 1--day programmable and non--programmablePreferred t Series Thermostat Control is a wall--mounted, low--voltage control which combines temperature and humidity control in either a single unit or a two--piece unit. In two--piece configuration, the relays are ...

Page 4 - INSTALLATION CONSIDERATIONS; Power

4 INSTALLATION CONSIDERATIONS Power This control is powered by 24VAC only. It requires 24VAC (Rh and/or Rc and C terminals) of the low--voltage transformer to be connected to it for properoperation. It will not operate without these 2 connections. Rh and Rc are connected via PCB breakout jumper. See...

Page 6 - Remote Indoor Temperature Sensor; The Preferred Series AC/HP Control can be installed in one of two

6 dedicated sensor wires may be used for its connection. Details are provided insensor instructions. Remote Indoor Temperature Sensor A remote temperature sensor may be used with the programmable heat pump and programmable air conditioner thermostats where it is desirable to install thethermostat in...

Page 7 - INSTALLATION

7 INSTALLATION Carton contains the following components. See Fig. 2 for programmable modelsor Fig. 3 for non--programmable models. A07756 Fig. 2 -- T6--PAC / T6--PHP Carton Contents 1. Display Module2. Stand--off for Equipment Control Module3. Screws and pig tail4. Equipment Control Module

Page 8 - AC/HP Control Location; Close to or in a frequently used room, preferably on an inside parti-

8 A07757 Fig. 3 -- T6--NAC / T6--NHP Carton Contents 1. Display Module2. Stand--off for Equipment Control Module3. Screws and pig tail4. Equipment Control Module AC/HP Control Location AC/HP Control should be mounted: S Approximately 5 ft (1.5m) from floor. S Close to or in a frequently used room, p...

Page 9 - Install AC/HP Control; ELECTRICAL OPERATION HAZARD; WARNING

9 AC/HP Control should NOT be mounted: S Close to a window, on an outside wall, or next to a door leading to the outside. S Exposed to direct light or heat from a lamp, sun, fireplace, or other temperature--radiating objects which could cause a false reading. S Close to or in direct airflow from sup...

Page 10 - UNIT DAMAGE HAZARD; Failure to follow this caution may result in equipment damage; CAUTION; If an existing thermostat is being replaced

10 UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damage or improper operation.Improper wiring or installation may damage AC/HP Control. Check to make sure wiring is correct before proceeding with installation or turning on power. CAUTION ! 1. Turn off all power to equipme...

Page 11 - ENVIRONMENTAL HAZARD; Failure to follow this caution may result in environmental; NOTE; : The 2--wire pigtail is not intended to support the weight of the User

11 ENVIRONMENTAL HAZARD Failure to follow this caution may result in environmental damage.Mercury is a hazardous waste. Federal regulations require that Mercury be disposed of properly. CAUTION ! Two--Piece Installation The following steps should be followed for the installation of the two--piececon...

Page 13 - if needed. Make sure all wires extend through hole in mounting base.

13 2. Route wires through large hole in mounting base. Level mounting base against wall (for aesthetic value only—Display Module need not be lev- eled for proper operation) and mark wall through 2 mounting holes. SeeFig. 6. A07165 Fig. 6 -- Backplate Mounting 3. Drill two 3/16--in. mounting holes in...

Page 14 - Black is Vg

14 6. Match and connect equipment wires to proper terminals of each connector block being careful not to over tighten the screws. Correct polarity must be observed when connecting the two wires from the Equipment ControlModule to the thermostat mounting base. If wires are connected incorrect-ly, the...

Page 17 - IMPORTANT NOTE: Equipment Control Module should not be mounted

17 10. Find suitable indoor mounting location for Equipment Control Module, either near or on equipment. See Fig. 11. IMPORTANT NOTE: Equipment Control Module should not be mounted to duct work or below any other controls or equipment (i.e. humidistat, humidifier, etc.). A07217 Fig. 11 -- Equipment ...

Page 19 - Turn on power to equipment. On power up, all display segments will

19 A07218 Fig. 13 -- Cover on Equipment Control Module 14. Turn on power to equipment. On power up, all display segments will light for 5 sec. For the next 5 sec a 2--digit code appears on large displaywhich identifies AC/HP Control configuration. Refer to Option 33. a. AC — 1--stage air conditioner...

Page 22 - Set AC/HP Control Configuration; Option 06 — Cooling Lockout Below 55

22 9. Turn on power to equipment. On power up, all display segments will light for 5 sec. For the next 5 sec a 2--digit code appears on large display which identifies AC/HP Control configuration. Refer to Option 33. a. AC — 1--stage air conditioner, AC, HP b. HP — 1--stage heat pump, HP only c. H — ...

Page 23 - Option 25* — Number of Programmable Periods per Day

23 Option 07 — ZoningOption 08 — Auxiliary Heat Lockout Temperature Setting (only available when heat pump is used and whenoutdoor air temperature sensor is present) Option 10 — Reversing ValveOption 11 — Adjustable Setpoint DeadbandOption 12 — Smart Recovery (programmable models only)Option 13 — Ro...

Page 24 - Configuration Options —Selection; Option 01 — Equipment Type

24 Option 31* — Daylight Savings Time Configuration (programmable models only) Option 32 — Furnace Heat StagingOption 33 — Single or Two--Piece InstallationOption 99 — Reset to Factory DefaultsTO ENTER CONFIGURATION MODEPress and hold FAN button for approximately 10 sec. The Display Module is now in...

Page 25 - indoor fan coil with no strip heaters.; Option 02 — Clean Filter Timer

25 AC model — Range: AC, H, C.HP — operates a single--speed heat pump with a fan coil.AC — operates a single--speed AC.H — operates a heat--only system. Furnace or fan coil only; no outdoor unit. C — operates a cool only--system. Outdoor AC unit with an indoor fan coil with no strip heaters. Default...

Page 26 - to prevent cooling below 55; Option 07 — Zoning

26 select OFF. Some auxiliary heaters require separate G signal to turn on blower. Inthis case, select On.Default is OF (off). Option 05 — Room Air Temperature Sensing (programmable models only) This selection determines which sensor the control will use for measuring roomair temperature. Room air t...

Page 28 - Option 13 — Room Air Temperature Offset Adjust; The number of; Option 15 — Enable Auto Mode

28 programmed. Not available with non--programmable thermostats or whenthermostat is configured as non--programmable.Default is 90. Option 13 — Room Air Temperature Offset Adjust The number of _ F to be added to the displayed temperature to calibrate or deliberately miscalibrate the measured room te...

Page 31 - Option 25 — Number of Programmable Periods

31 Option 21 — Keypad Lockout (non--programmable models only) This selection allows the installer to limit access to the keypad. Selections are OF (off), 1, 2.OF (off) — The user has full access to the keypad.1 — The user has access to change the setpoints.2 — The entire keypad is locked. When a but...

Page 33 - Option 30 — Programmable Fan (programmable models only)

33 OF (off) — The Humidifier Pad Reminder is disabled and will never bedisplayed.1--24 — The number of months after which the Humidifier Pad Reminder iconwill be displayed, “CHECK HUM PAD”.Default is OF (off). Option 30 — Programmable Fan (programmable models only) This selection allows the homeowne...

Page 34 - Option 33 — Single or Two--Piece Installation

34 Daylight Savings Time by setting the day of the week by selecting theappropriate triangle icon next to the days of the week, the month of the year will be set in the clock hours location (range 1--12) and the week of the month will beset in the clock minutes location. The week of the month select...

Page 35 - Option 99 — Reset to Factory Defaults

35 Option 99 — Reset to Factory Defaults Use this capability to reset the stat to “out of the box” conditions. BEWARE! All configuration settings, program settings, clock, and calendar which have beenmanually entered will be lost!When this option is selected, the configuration number (99), will appe...

Page 37 - 0 sec after G signal is removed.; Final Settings; conform to the Energy Star; Table 1 – Energy Star Default Schedule

37 TO TEST FANFan button switches FAN icon between AUTO and On. While On is displayed, G output will be energized, turning fan on. Allow up to 10 sec after button ispressed for fan to turn on and off. On some fan coils, fan continues to operate for 90 sec after G signal is removed. Final Settings Be...

Page 39 - OPERATIONAL INFORMATION; Timers

39 Vacation (programmable models only) A vacation selection is available specifically for times where the home will not be occupied for an extended period. Vacation mode has an automatic hold,meaning that setpoints are not affected by the programmed schedule. Vacation mode is active for a specified ...

Page 40 - Cycle Timer; F (usually due to a large change; Defrost; provide homeowner comfort during the defrost cycle

40 Cycle Timer Based on the selection of 2, 4, or 6 cycles per hour, this timer is set to 30, 15, or 10 minutes. This much time must elapse from the start of one cycle beforeanother cycle can start. It serves to impose the cycles per hour limits. It can be defeated for one cycle by simultaneously pr...

Page 41 - Equipment On Indicators; auxiliary

41 Three--Minute Minimum on Time In normal operation, when a stage turns on, it will not turn off for a minimum of 3 minutes. If the setpoint is changed, this timer is canceled, allowing theequipment to turn off immediately when the demand is removed. Heat/Cool Setpoints (Desired Temperature) A mini...

Page 42 - Programmable Fan (programmable models only); The fan output can be programmed based on period of the day. When; Dry Contact

42 Programmable Fan (programmable models only) The fan output can be programmed based on period of the day. When programming for each day and period the fan can be set to On or AUTO. Dry Contact On the programmable models, the dry contact that can be used for control of anauxiliary device. The dry c...

Page 43 - TROUBLESHOOTING; Error Codes; operate from the temperature sensed by the working sensor.

43 TROUBLESHOOTING If the display module doesn’t power up after power is applied, check the Rc/Rhand C terminals for 24VAC. If 24VAC is present, check the voltage between Vg and V+. This voltage will be approximately 12--20VDC. If voltage is present, check the polarity to make sure it is wired corre...

Page 44 - Table 3 – Equipment Configuration Outputs

44 Table 3 – Equipment Configuration Outputs EQUIPMENT- CONFIGURATION OPTION #1 HARDWARE CONFIGURATION COOL STAGE 1 COOL STAGE 2 HEAT STAGE 1 HEAT STAGE 2 HEAT STAGE 3 EM HEAT STAGE 1 Single--stage AC AC Y/Y2 -- W/W1 -- -- -- Single--stage AC HP Y/Y2 -- W/W1 W/W1 O/W2/B -- -- Single--stage HP RVS = ...

Page 45 - WIRING DIAGRAMS

45 WIRING DIAGRAMS Display module Display module wall mount Equipment Control Module Fan Coil Heat Pump V+ V+ Vg Vg O O V+ V+ RVS/Heat Stage 2 O/B W 2 W 3 W 2 Vg Vg Heat Stage 1 W /W 1 W 2 Compressor Y/Y2 Y Y Not Used Y1 Fan G G 24VAC Hot Heating Rh R R 24VAC Hot Cooling Rc Dry Contact 1 D1 Dry Cont...

Page 54 - THERMOSTAT CONFIGURATION RECORD

54 THERMOSTAT CONFIGURATION RECORD Installer _________________________ Model Number ______________________________ Date _________________________ A. Hardware Configuration __________ Seal Hole In Wall B. Mode Settings __________ Mode (Off, Heat, Cool, Auto, Em Heat) __________ Heating Setpoint Value...