Brinkmann 400 - Manuals

6 Tank Holder INSTALLING THE LP GAS CYLINDER (TANK) ONTO THE GRILL: 1. Check that the cylinder valve is closed by turning the knob clockwise. Inspect cylinder valve rubber seal for cracks or deterioration. Do not use propane tank with damaged seal as a gas leak may occur. 2. Place the cylinder into ...

7 HOSE AND REGULATOR: Your grill is equipped with a Type 1 connection device with the following features: 1. The system will not allow gas fl ow from the cylinder until a positive connection to the valve has been made. Note: The cylinder valve and all grill burner knobs must be turned OFF before any...

8 WHEN TO PERFORM A LEAK TEST: • After assembling your grill and before lighting for the fi rst time, even if purchased fully assembled. • Every time the LP gas cylinder is refi lled, exchanged or if any of the gas components are disconnected or replaced. • Any time your grill has been moved. • At l...

9 LIGHTING THE MAIN BURNERS: 1. Open lid before lighting burner. 2. Make sure all control knobs are in the “OFF” position. 3. Select the burner to be lit. Push and turn the control knob of that burner to the “HIGH” position 4. Press the electronic igniter and hold for 3–5 seconds to light burner 5. ...

10 6. Repeat steps 3–5 for lighting each burner. Always use electronic igniter for lighting each burner. If burner does not ignite using the push-button igniter, wait 5 minutes, see “Match Lighting the Main Burners” section. 7. To turn off, turn each control knob clockwise until it locks in the “OFF...

11 • Read and follow all warnings and instructions contained in the preceding sections of this manual. • Never use charcoal, lava rocks or wood briquets in a gas grill. Flavoring chips must be contained in a metal smoking box to contain ash and prevent fi res. • DO NOT cover cooking grates or other ...

TURNING OFF THE GRILL: 1. Turn off the cylinder valve. 2. Turn all burner control knobs to the “OFF” position. Note: Turn off LP cylinder fi rst to prevent gas from being left in the system under pressure. CAUTION: • The cylinder valve should always be in the off,or closed, position when the grill i...

13 WARNING: If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain on the cooking surfaces prior to grilling as loose bristles may attach to food. CLEANING INTERIOR OF GRILL: • We recommend cleaning off food residue immediately after cooking by gently scrubb...

14 BURNER ASSEMBLY/MAINTENANCE: • Although your burners are constructed of stainless steel, they may corrode as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage. If found, replace the burner. • DO...

15 BEFORE STORING YOUR GRILL: • Ensure that the cylinder valve is fully closed. • Clean all surfaces. Lightly coat the burners with cooking oil to prevent excess rusting. • If storing the grill indoors, disconnect the LP tank and leave the LP tank OUTDOORS. • Place a protective cap cover on the LP t...

16 TROUBLE SHOOTING: Problem Possible Cause Prevention/Cure Burner will not light LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank, turn LP gas tank valve to “OPEN” LP gas tank is low or empty Check if LP gas tank is empty. If empty, replace or refi ll. LP gas ...

17 Problem Possible Cause Prevention/Cure Flame blows out High or gusting winds Do not use grill in high winds Low on LP gas Replace or refi ll LP gas tank Burner holes may be obstructed Refer to “Burner Assembly/Maintenance” instructions Flow limiting device tripped Refer to “Regulator Resetting Pr...

18 ASSEMBLY INSTRUCTIONS: 8 M6 X 12 mm Bolts (Black) 17 M6 X 12 mm Bolts (Silver) 4 M6 X 30 mm Bolts (Silver) 2 M5 X 12 mm Bolts (Black) 2 M4 X 12 mm Bolts (Black) 8 M4 X 12 mm Bolts (SIlver) 1 Shoulder Bolt (Black) Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before y...

19 READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT. The following tools are required to assemble this Brinkmann Heavy-Duty Gas Grill: • Screwdriver• Hex Nut Wrench 1 Grease Tra...

Choose a good, cleared assembly area and get a friend to help you put your grill together. Laycard board down to protect grill fi nish and assembly area. CAUTION: Some parts may contain sharp edges. Wear protective gloves if necessary. Step 1 Turn cart base upside down, use two M6 X 12 mm bolts (sil...

Step 3 Remove the spring, washer, and bolt from the tank gauge bracket. Set aside for use in Step 5. Attach the tank gauge bracket onto the base using two M6 X 12 mm bolts (sliver) as illustrated in Figure 1. Attach the tank gauge needle assembly to the base and the bracket and secure with a hinge p...

Step 6 Using four M6 X12 mm bolts (silver) attach the left panel and the right panel to the cart base. Step 7 Using four M6 X 12 mm bolts (silver) attach the back panel. Back Panel 23 Right Panel Left Panel

Step 8 To attach the wind defl ector, insert the upper cart brace pre-attached bolts through the key holes of the wind defl ector, slide the wind defl ector downward and tighten the bolts securely. See Figure 1 and 2 below. Use four M6 X 30 mm bolts (silver) and two M6 X 12 mm bolts (silver)to attac...

©2012 The Brinkmann Corporation Dallas, Texas 75244 U.S.A. 140-4580-S0812 Owner’s Manual for Model Manual del Propietario para el Modelo 810-4580-S The Brinkmann Corporation warrants to the original pur chas er that the Brinkmann Heavy-Duty Gas Grill is free from defects due to workmanship or materi...