BILLY GOAT TKD505SPT - Manuals

Page 2 - Part No. 890316 Form No. F082195D; SOUND TESTS; SOUND; BAROMETRIC PRESSURE:; IN THE INTEREST OF SAFETY; TABLE OF CONTENTS; VIBRATION; The Engine Exhaust from this product contains chemicals known

Part No. 890316 Form No. F082195D THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTYDAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & EN-GINE MANUAL.” WARNING: DO NOT 1. DO NOT run en...

Page 3 - Part No. 890316 Form No. F082195D; QUICK DISCONNECT; GENERAL SAFETY; PACKING CHECKLIST; Tecumseh; ASSEMBLE

Part No. 890316 Form No. F082195D Page 3 of 12 For your safety and the safety of others, these directions should be followed: Use of Ear Protection is recommended whileoperating this machine. Do not operate this machine without first readingowner's manual and engine manufacturer's manual. Use of Eye...

Page 4 - Manual; Manual; Literature Checklist; WARNING; Start; Stop; CONTROLS; ENGINE LABELS; DANGER; PULL TO ENGAGE CLUTCH

Part No. 890316 Form No. F082195D EVERY 10 HOURS 830502 OIL CHAIN WARNING 900327 Page 4 of 12 Owner's Manual Literature KD / TKD Accessories Check Owner's Manual 890316 Literature KD / TKD Accessories 890317 Check Literature Checklist These labels should be included on your Vacuum. If any of thesela...

Page 5 - Use caution when using chipper; TERMITE; VACUUM NOZZLE HEIGHT ADJUSTMENT:; djust nozzle close to debris,; IF YOUR UNIT FAILS TO START:; Maximum; OPERATION; CHIPPING OPERATION; CLEARING A CLOGGED CHIPPER HOPPER; VACUUMING OPERATION; STARTING

Part No. 890316 Form No. F082195D Page 5 of 12 Under normal circumstances, allow time for machine to clear all wood from chipper hopper before stopping engine. Otherwise, remaining pieces of wood will jaminside of chipper when engine stops. See Tamper on page 7. Disconnect spark plug wire.Remove deb...

Page 6 - continued; Frequently empty debris to prevent bag overloading with; DO NOT place bag on or near hot surface; (see Safety Warnings; Run machine at idle to quarter throttle.; DEBRIS BAG

Part No. 890316 Form No. F082195D Page 6 of 12 16 OPERATION continued Note: Frequently empty debris to prevent bag overloading with more weight than you can lift. An optional bag and dust cover is available for use where debris willbe vacuumed in dusty conditions (see Optional Accessories shown on p...

Page 7 - GROUND SPEED; Do not store with debris in bag.; PROPULSION; Tamper Storage Position.

Part No. 890316 Form No. F082195D Page 7 of 12 GROUND SPEED can be varied by applying slight downward pressure to handle during operation (to allow drive wheelspartial slippage) or by changing the engine rpm. For improved control in confined areas, this machine can befreewheel pushed forward or back...

Page 8 - MAINTENANCE; CHIPPER BLADE REMOVAL AND SHARPENING; The chipper blade gap is factory set and should be checked; Chipper blades are normal replaceable wear items.; Chipper blade is sharp.; INCORRECT; your unit may or may not have required the use of shim washers; EDGE OF CHIP; Using a penetrating oil can help loosen a stuck impeller.; IMPELLER REMOVAL

Part No. 890316 Form No. F082195D Page 8 of 12 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING Depending on the type and amount of wood being chipped, thechipper blade will eventually get dull, losing it’s cutting ability.Evidence of a dull blade is a noticeably reduced chipping ability ora rough c...

Page 9 - . If chipper blade properly clears anvil surface, proceed to step 20.; and; CHIPPER; R o d; Maintenance Schedule; CLUTCH ADJUSTMENT; DRIVE

Part No. 890316 Form No. F082195D Page 9 of 12 MAINTENANCE continued 19 . If chipper blade properly clears anvil surface, proceed to step 20. If not, return to (step 14) and add or subtract shim washers asneeded to obtain a correct gap. 20. Reinstall engine, impeller and jackshaft assembly component...

Page 10 - PARTS DRAWING

Part No. 890316 Form No. F082195D R Page 10 of 12 18 PARTS DRAWING TKD505SPT

Page 12 - TROUBLESHOOTING; Before Requesting Service Review These Suggestions; Engine Service and Warranty; Contact your nearest engine manufacturer's autho-; Serial Plate; WARRANTY PROCEDURE

Part No. 890316 Form No. F082195D Page 12 of 12 Part No. Engine stalls or labors whenchipping. Feeding branches into chipper too rapidly. Engine service may berequired. Feed branches at a slower rate. Service engine. Poor chipping performance. Extremely hard wood. Dull or damaged chipper blade. Avoi...