BILLY GOAT HP3400 - Manual - manualsarea.com

Page 2 - HP Owner’s Manual; ABOUT THIS MANUAL; for purchasing a BILLY GOAT; CONTENTS

Part No 521302 Form No F101910A 2 HP Owner’s Manual ABOUT THIS MANUAL THANK YOU for purchasing a BILLY GOAT ® HP Mower . Your new machine has been carefully designed and manufactured to provide years of reliable and productive service. This manual provides complete operating and maintenance instruct...

Page 4 - GENERAL SAFETY INSTRUCTIONS and SYMBOLS; is recommended when operating this equipment.

Part No 521302 Form No F101910A 4 HP Owner’s Manual GENERAL SAFETY INSTRUCTIONS and SYMBOLS The safety symbols shown below are used throughout this manual. You should become familiar with them before assembling, operating, or servicing this equipment. This symbol indicates important information that...

Page 6 - SOUND

Part No 521302 Form No F101910A 6 HP Owner’s Manual SOUND SOUND LEVEL 82 dB(a) at Operator Position 102 dB(a) Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 9-24-2010 under the conditions listed below. Sound power level listed is the highest value for any model cove...

Page 7 - INSTRUCTION LABELS; ENGINE LABELS; BRIGGS AND STRATTON

Part No 521302 Form No F101910A 7 HP Owner’s Manual INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT ® HP Mower. If any labels are damaged or missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided f...

Page 8 - PACKING CHECKLIST; PUT OIL IN ENGINE BEFORE STARTING; all safety instructions before assembling unit.; TAKE CAUTION; when removing the unit from the box.; NOTE

Part No 521302 Form No F101910A 8 HP Owner’s Manual PACKING CHECKLIST Your Billy Goat Mower is shipped from the factory in one crate, completely assembled except for the handles and controls. PUT OIL IN ENGINE BEFORE STARTING ASSEMBLY READ all safety instructions before assembling unit. TAKE CAUTION...

Page 9 - : See maintenance section for

Part No 521302 Form No F101910A 9 HP Owner’s Manual OPERATION Like all mechanical tools, reasonable care must be used when operating machine. Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety. PUT OIL ...

Page 10 - objects might be a hazard.

Part No 521302 Form No F101910A 10 HP Owner’s Manual CUTTING OPERATION CAUTION : Shut off the blades when crossing gravel drives, walks or roads and under all conditions where thrown objects might be a hazard. CLEARING A CLOGGED CUTTING DECK : Turn engine off and wait for blade to stop completely. D...

Page 11 - PROPULSION; can be varied by selecting a higher or lower gear using the; : Only change gear selection; HILLSIDE MOWING; Never mow on any slope greater than 15 degrees. Always; BLADE CLUTCH; The blade clutch must be either fully engaged for cutting or fully

Part No 521302 Form No F101910A 11 HP Owner’s Manual PROPULSION This unit is self-propelled, and is controlled by an operator presence control. To engage the wheel drive, lift the operator's DRIVE lever on the right side against operator's handle. The drive is disengaged by releasing the lever. (See...

Page 12 - ERIODIC; : When sharpening the blade it is a good idea to check the balance of; DO NOT; change the blades with the unit running.

Part No 521302 Form No F101910A 12 HP Owner’s Manual MAINTENANCE P ERIODIC M AINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every Use (daily) Every 5 hrs or (daily) Every 25 Hrs Every 50 Hrs (Yearly) Every 150 Hrs Inspect for loose, worn or dama...

Page 13 - BELT REPLACEMENT; CAUTION

Part No 521302 Form No F101910A 13 HP Owner’s Manual BELT REPLACEMENT When replacing one belt the other should be inspected for wear and replaced if worn. It is good practice to change both belts when either is worn beyond use. Use only original equipment belts for replacement. Billy Goat uses only ...

Page 14 - CABLE ADJUSTMENTS; Transaxle Drive Control Cable Adjustment

Part No 521302 Form No F101910A 14 HP Owner’s Manual CABLE ADJUSTMENTS Transaxle Drive Control Cable Adjustment When the transaxle drive belt slips, the drive control cable needs to be adjusted or the belt needs to be replaced with a new belt. Cable Adjustment: 2. Using a ½ “ open end wrench, turn t...

Page 15 - WARRANTY CLAIM PROCEDURE; Should a BILLY GOAT

Part No 521302 Form No F101910A 15 HP Owner’s Manual Troubleshooting When servicing engine refer to specific manufacturers engine owner's manual. All engine warranty is covered by the specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing eng...

Page 16 - PARTS DRAWING HP

Part No 521302 Form No F101910A 16 HP Owner’s Manual PARTS DRAWING HP

Page 17 - PARTS LIST

Part No 521302 Form No F101910A 17 HP Owner’s Manual PARTS LIST Item No. Part Number Description Qty 1 521208 Base Engine W A HP 1 9 521122 Belt 4L x 33 1 10 521112 Belt 5l x 60 1 15 521105 Engine 10.5 HP Intek 1 16 521100 Clutch HP 1 19 521212 Idler Arm W A 1 20 521121 Pulley idler arm HP 1 23 5211...

Page 24 - MAINTENANCE RECORD; Date

Part No 521302 Form No F101910A 24 HP Owner’s Manual MAINTENANCE RECORD Date Service Performed