BILLY GOAT FM3300IN, FM3300INE - Manual

Page 2 - DO NOT transport unit with fuel in tank.; TABLE OF CONTENTS; VIBRATION; VIBRATION LEVEL 1.8 g; IN THE INTEREST OF SAFETY; The Engine Exhaust from this product contains chemicals known; SOUND; Sound level of 95 dBA at operator position

Part No. 520166 Form No. F112003A because contact may cause burns. 22. DO NOT run engine without air cleaner or air cleaner cover. 23. DO NOT operate during excessive vibra-tion!24. DO NOT leave machine unattended while in operation. 25. DO NOT park machine on a steep grade or slope. WARNING: DO 1. ...

Page 3 - GENERAL SAFETY; Do not mow excessively steep slopes.

Part No. 520166 Form No. F112003A Page 3 of 20 For your safety and the safety of others, these directions should be followed: Do not operate this machine without fi rst reading owner's manual and engine manufacturer's manual. Use of Eye and Breathing protection is recom- mended when using this machi...

Page 4 - Part No. 520166; ASSEMBLY; PUT OIL IN ENGINE BEFORE STARTING.

Part No. 520166 Form No. F112003A 11 ASSEMBLY .. .. Page 4 of 20 PUT OIL IN ENGINE BEFORE STARTING. Read all safety and operating instructions before assembling or starting this unit. Your Billy Goat Mower is shipped from the factory in one crate, completely assembled except for the handles and cons...

Page 5 - CONTROLS; Throttle Control; Manual; LITERATURE ASSY; Electric Start Only; WARNING; Speed Control; Ty Wrap; ENGINE LABELS; long Qty 1; Warranty; Declaration

Part No. 520166 Form No. F112003A Page 5 of 20 CONTROLS Throttle Control 13 Check Owner's Manual 520166 Literature Checklist 12 LITERATURE ASSY Electric Start Only Pull up on the switch then push forward to start the engine. 3 3 " T R I P L E B L A D E E L E C T R I C S TA R T M O D E L P a rt N...

Page 6 - TO PREVENT INJURY; DANGER; PATENT

Part No. 520166 Form No. F112003A P a rt No: 520079 3 3 " T R I P L E B L A D E M O W E R Follow all instructions in Owner's Manual.Go across slopes, not up and down.Do not mow when children or others are around.Look down and behind before and while movingbackwards.Keep safety guards, shields, s...

Page 7 - CUTTING OPERATION; OPERATION; STARTING

Part No. 520166 Form No. F112003A Like all mechanical tools, reasonable care must be used when operating machine. Do not operate unit in areas where bystanders may be present. D o n o t o p e ra t e i f ex c e s s i ve v i b ra t i o n o c c u r s. I f ex c e s s i ve v i b ra t i o n o c c u r s, s...

Page 8 - continued; CUTTING HEIGHT ADJUSTMENT; spacers; BLADE CLUTCH

Part No. 520166 Form No. F112003A OPERATION continued 16 Page 8 of 20 Figure 16-2 Figure 16-1 16.3 CUTTING HEIGHT ADJUSTMENT Cutting height can be adjusted from 1.0" to 3.5" by placing spacers above or below caster spindles. For easiest adjust-ment change the height on one side at a time. To...

Page 9 - STORAGE; HILL; PROPULSION

Part No. 520166 Form No. F112003A Never store engine indoors or in enclosed poor ly ventilated areas with fuel in tank, where fuel fumes may reach an open fl ame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.If engine is to be unused for 30 days or more, ...

Page 10 - MAINTENANCE; inspected on a regular basis and replaced if worn.; Maintenance Operation; Maintenance Schedule; MAINTENANCE HISTORY; Service Performed

Part No. 520166 Form No. F112003A Use only a qualifi ed mechanic for any adjustments, disassembly or any kind of repair . WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN MACHINE OFF, MAKE SURE A L L M OV I N G PA RT S C O M E TO A C O M -PLETE STOP. 17 MAINTENANCE RECONNECT SPARK PLUG WIRE,AND ALL GU...

Page 11 - CABLE ADJUSTMENTS; Brake Adjustment; STARTER SWITCH WIRING

Part No. 520166 Form No. F112003A CABLE ADJUSTMENTS 17.1 Brake Adjustment The brake control cable is spring loaded and requires no adjustment; however, the transaxle brake is adjustable. When the mower is in neutral and can be pushed by hand without depressing the brake lever, the transaxle brake ne...

Page 12 - BELT REPLACEMENT; Blade Drive Belt Replacement; BLADE REMOVAL / SHARPENING

Part No. 520166 Form No. F112003A Page 12 of 20 NOTE: When sharpening the blade it is a good idea to check the balance of the blade. A properly balanced blade will increase life of the bearings and other components. Tools required: ratchet, 3/4” inch socket, torque wrench, ade-quate support, block t...

Page 13 - Spindle Drive Belt; Transaxle Drive Belt Replacement

Part No. 520166 Form No. F112003A Page 13 of 20 Spindle Drive Belt Tools required: 3/8 inch socket, 1/2 inch socket. 1. Disconnect spark plug wire.2. Follow steps to remove the Blade Drive Belt (on the spindle pulley side only) from the previous section.3. Loosen the two idler plate nuts (Item 143)....

Page 14 - When the blade clutch control lever is pressed down, the; BRAKE PUCK REPLACEMENT

Part No. 520166 Form No. F112003A Tools Required: 5/32” Allen wrench; 3/8” wrench. 1. Remove the spark plug wire.2. Remove the belt deck cover.3. Remove the brake spring (A) and control cable spring (B) (see fi gure 17-10).4. Remove the blade drive belt (C) from the drive pulley (D). 5. Using a 3/8”...

Page 15 - PARTS DRAWING

Part No. 520166 Form No. F112003A Page 15 of 20 130 175 21 87 179 155 81 178 155 41 174 145 53 139 20 62 126 38 42 1 38 126 127 7 171 33 35 103 18 151 71 144 126 180 151 144 144 151 144 56 119 127 5 147 2 16 17 65 171 5 46 23 173 171 172 167 168 165 164 163 24 168 169 170 166 173 172 ITEM DESCRIPTIO...

Page 19 - ACCESSORIES

Part No. 520166 Form No. F112003A Page 19 of 20 Item No. Part No. Description Qty 1 520012 GRASS CATCHER BAG 1 2 520038 WIRE FRAME GRASS CATCHER FM 1 3 520069 GRASS CATCHER MOUNT WA FM 1 4 520059 BRACKET GRASS CATHCER LATCH L FM 1 5 520060 BRACKET GRASS CATHCER LATCH R FM 1 6 8041006 SCREWCAP 1/4...

Page 20 - Engine Service and Warranty; Contact your nearest engine manufacturer's authorized; WARRANTY PROCEDURE; Solution; TROUBLESHOOTING; Before Requesting Service Review These Suggestions; Model; ENGINE

Part No. 520166 Form No. F112003A Page 20 of 20 Purchased from Purchase Date Engine Service and Warranty Contact your nearest engine manufacturer's authorized servicing dealer. 22.1 21 Serial Plate R ecord your machine model, serial number and date-of-purchase and where purchased 22 R BILLY GOAT IND...

BILLY GOAT FM3300IN, FM3300INE - Manual

Table of Contents:

Summary

Other BILLY GOAT Models