American Audio V4000 plus - Manuals

Page 2 - NO SE ABRA

This symbol is intended to alert the user to the presence of non insulated "dangerous voltage" within the product's enclosure that may be of suffi cient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user of the presence of important operati...

Page 3 - CAUTION; POUR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO YOUR AUTHORIZED AMERICAN AUDIO ® DEALER. CAUTION Do not open - risk of electric shock FOR OPTIMUM PERFORMANCE AND RELIABILITY DO NOT PRESENT THE AMPLIFIER WITH A S...

Page 4 - plusTM

Important Precautions • To reduce the risk of electrical shock or fi re, do not expose this unit rain or moisture• Do not spill water or other liquids into or on to your unit• Do not attempt to operate this unit if the power cord has been frayed or broken• Do not attempt to remove or break off the g...

Page 5 - Front Panel Control

1. Power Switch - This switch is used to control the units main power. 2. Channel 1 Gain Control - This rotary knob is used to control the out- put signal of channel one. Turning the knob in a clockwise direction will increase signal output. 3. Channel 1 Limiter Switch - This is used to activate the...

Page 6 - Rear Panel Control

16 32 28 15 29 27 33 26 25 24 23 22 20 21 18 19 17 15 Rear Panel Control 15. Cooling Fans - Dual high speed cooling fans 16. Channel 2 TRS Input - Channel two 1/4” female jack. Excepts ei- ther a balanced or unbalanced plug. See page 7 for more details. 17. Channel 2 XLR Input - Channel two 3-pin XL...

Page 7 - Unbalanced TS 1/4” Plug; Balanced TRS 1/4” Plug; Male XLR Pin Confi gu; US ITT Standard; Set Up; INPUTS; plus

Unbalanced TS 1/4” Plug Hot (+) Negative (-) Diagram 5 Balanced TRS 1/4” Plug Ground/Shield Hot (+) Negative (-) Diagram 4 2 Hot (+ data) 3 Negative (- data) 1 Ground/Return/ 0v) 1 2 3 Male XLR Pin Confi gu Male XLR Pin Confi Male XLR Pin Confi ration: US ITT Standard Diagram 3 OUTPUTS:Binding Post/...

Page 8 - NL4FC connectors from your local audio dealer.

Bare Wire Connections: When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire insulation 1/2” (13mm). Insert the bare wire into the hole that was revel...

Page 9 - Mono Bridge Operation -; The voltage across the output terminals of a bridged V4000

OPERATING MODES: Always configure your amplifier operating mode before beginning operation. If you want to change it dur- ing performance. You must decrease the gain controls to their lowest levels to protect the speakers from any popping noise. Stereo Operation - Page 10/Figure 9 details an example...

Page 11 - RF; FUNCTION INDICATORS

put). Short Circuit Protection can usually be traced back to the signal output line (i.e. speaker line). Check the line from the output terminal of the amplifier to the speaker. If this line good, check the internal speaker connections and components. A short circuit will usually be traced to a bad ...

Page 13 - Use either the Speakon or the banana jacks; Stereo Subwoofer Mode Speaker Set-Up; Bridge Subwoofer Mode Speaker Set-Up

Positive (+) Lead Negative (-) Lead Do Not Use Ch2 Inputs Do Not Use Ch2 Inputs Use Ch1 Inputs Use Ch1 Inputs Set to Bridge Set to Subwoof Use Ch2 Inputs Use Ch2 Inputs Use Ch1 Inputs Use Ch1 Inputs Set to Stereo Set to Subwoof Set to Subwoof Figure 14 Figure 15 Use either the Speakon or the banana ...

Page 14 - TYPICAL MONO BRIDGE SET-UP; OHM MINIMUM; SPEAKERS; OHM MINIMUM; SPEAKERS; OHM MINIMUM

TYPICAL MONO BRIDGE SET-UP SPEAKERS 4 OHM MINIMUM TYPICAL STEREO OUTPUT CONNECTIONS SPEAKERS 2 OHM MINIMUM SPEAKERS 2 OHM MINIMUM Use Channel 1 Inputs Only (XLR or 1/4” Jacks) X X X X X X X X Use Speakon or Banana Jacks ©American Audio® - www.americandj.com - V4000plus™ Power Amplifier User Manual P...

Page 15 - V-SERIES AMPLIFIER SPECIFICATIONS

Output Power: 2 ohms, 1 khz 1% THD 2 ohms, 1 khz 1% 2 ohms, 1 khz 1% 4 ohms, 1khz, 1% 4 ohms, 1khz, 1% 4 ohms, 1khz, 1% THD 8 ohms, 1khz 1% THD 8 ohms, 1khz 1% 8 ohms, 1khz 1% (Bridge Mode, mono) 4 ohms, 1khz, 1% THD 4 ohms, 1khz, 1% 4 ohms, 1khz, 1% 8 ohms, 1khz, 1% THD 8 ohms, 1khz, 1% 8 ohms, 1kh...