American Audio VLP300 - Manual

PROFESSIONAL POWER AMPLIFIER VLP300 PRO CH A CLIP POWER 0 dB 10 15 10 6 3 1 80 30 15 POWER 15 10 CLIP PRO CH B 0 dB 10 6 3 1 80 30 15 11. Channel 1 gain Control - This rotary knob is used to control the output signal of channel one. Turning the knob in a clockwise direction will increase signal outp...

rear Panel ControlVLP600 & VLP1500 21. Cooling Fans - dual high speed cooling fans 22. Channel 2 XLr Input - channel two 3-pin XLr balanced input jack. See page 9 for more details. 23. Channel 2 trS Input - channel two 1/4” female jack. excepts either a bal- anced or unbalanced plug. See page 9 ...

rear Panel Control 37. aC Cord - Plug this cable into a standard wall outlet. check that the voltage in your area matches the amplifiers required voltage. 38. Channel 1 trS Input - channel one 1/4” female jack. excepts either a bal- anced or unbalanced plug. See page 9 for more details. 39. Channel ...

oUtpUts: binding post/banana plug - connect your speakers to the binding post outputs on the rear of the amplifier. The speaker wire may be connect by bare wire (directly connected, usually for permanent connections), banana plug, or spade connector. connections are made to channels 1 and 2 output’s...

spade Connector: (Figure 10) When connecting your speakers to the amplifier using spade connector; unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. insert the spade con-nector in to the binding post and tighten the caps down on t...

SPeakon aSSeMBLy: You will need a pair of neutrik Speakon ® nL4Fc connectors. You will also need high-quality two or four conductor speaker cable, a pair of needle-nosed pliers and a 1.5-mm Allen key to assemble the Speakon connectors to your speaker wire. To assemble the neutrik Speakon nL4Fc conne...

©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 12 operatIng MoDes: Always configure your amplifier operating mode before beginning operation. if you want to change it dur- ing performance. You must decrease the gain controls to their lowest levels to protect t...

©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 13 Mono Subwoofer - This operation is similar to the Stereo Subwoofer operation but in mono. When running subwoofers it is usually recommended to run them in mono mode to achieve a cleaner tighter low end. This op...

©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 14 put). Short Circuit Protection can usually be traced back to the signal output line (i.e. speaker line). check the line from the output ter- minal of the amplifier to the speaker. if this line good, check the i...

©American Audio® - www.americanaudio.us - vLP Series™ Power Amplifier user manual Page 15 tYpICaL Mono brIDge set-Up speaKers 8 oHm minimum tYpICaL stereo oUtpUt ConneCtIons speaKers 4 oHm minimum speaKers 4 oHm minimum use channel 1 inputs only (XLr or 1/4” Jacks) X use Speakon or Banana Jacks use ...

The vLP series carries a one year limited warranty. We recommend you fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a r.A. (return authorization) number. if the mixer is under warranty, y...

VLP SerIeS SPeCS Power supply: Ac 100v, 50/60Hz (Japan) Ac 110v, 60Hz (colombia) Ac 120v, 60Hz (u.S.A. and canada) Ac 127v, 60Hz (mexico) Ac 220v, 50Hz (chile and Argentina) Ac 220v, 60Hz (Philippines and Korea) Ac 230v, 50Hz (europe, new Zealand, South Africa, and Singapore) Ac 240v, 50Hz (Australi...