Alliance UU050L- Manuals

4 70457901 (EN) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Grounding Instructions ......................................................................... 44 For CE Models Only ........................................................................ 44Service/Ground Locatio...

70457901 (EN) 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Adjustments ......................................................................................... 83 Gas Burner Air Shutter ......................................................................... 83Airflow Swit...

70457901 (EN) 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Model Identification Information in this manual is applicable to these models: Gas Steam/Thermal Oil Electric 050 Series CA050LCA050NCK050NCT050LCT050NCU050LCU050NDR50G2-BA050LDR50G2-BA050NDR50G2-BK050ND...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 7 70457901 (EN) Includes models with the following control suffixes: 3B – reversing DX4 vended3O – DX4 OPL3V – DX4 vended3W – reversing DX4 prep for coin3X – DX4 prep for coinBB – reversing basic electronic, coinBC – ba...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 70457901 (EN) 8 Contact Information If service is required, contact the nearest Factory Authorized Service Center. If you are unable to locate an authorized service center or are unsatisfied with the service performed o...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 70457901 (EN) Safety Information Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal saf...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 70457901 (EN) 10 Save These Instructions Important Safety Instructions 1. Read all instructions before using the tumble dryer. 2. Install the tumble dryer according to the INSTALLATION instructions. Refer to the E...

70457901 (EN) 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions NOTE: All machines are shipped with extra nipple to convert to metric thread (from Standard). Specifications 050 Series 075 Series F75 Noise level measured during operation at operator ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 13 70457901 (EN) Cabinet Dimensions * Fire suppression system optional - may not be on machine. TMB2293N TMB2293N C B F D A K G J E I H Models A B C D E* F 050 Series Gas and Electric 781 mm (30.75 in.)...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 70457901 (EN) 14 Exhaust Outlet Locations TMB2238N A B C Models A B C 050/075 Series 137 mm (5.375 in.) 203 mm (8 in.) 340 mm (13.375 in.) F75 165 mm (6.5 in.) 254 mm (10 in.) 165 mm (6.5 in.)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 15 70457901 (EN) Gas Connection Locations TMB2239N A B Diameter A B 050/075 – 1/2 in. NPT 375 mm (14.75 in.) 1670 mm (65.75 in.) F75 – 3/4 in. NPT

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 70457901 (EN) 16 Electrical Connection Locations TMB2240N TMB82240N GAS AND STEAM ELECTRIC A A B B A B 83 mm (3.25 in.) 1918 mm (75.5 in.) NOTE: These figures are approximate dimensions only.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Specifications and Dimensions 17 70457901 (EN) Steam Connection Locations TMB2241N C A B D Diameter A B C D 3/4 in. NPT 387 mm (15.25 in.) 1848 mm (72.75 in.) 190 mm (7.5 in.) 1645 mm (64.75 in.)

70457901 (EN) 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation Pre-Installation Inspection Upon delivery, visually inspect the crate, carton and parts for any visible shipping damage. If the crate, carton, or cover is damaged or signs of possible damage are evident...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70457901 (EN) 20 Position and Level the Tumble Dryer Remove lint panel door, and unscrew the four shipping bolts (one at each corner). Remove tumble dryer from skid. NOTE: Do not throw bolts away – they are the leveling...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 21 70457901 (EN) IMPORTANT: If temperature sensors inside the tumble dryer register a temperature below 4.4°C (40°F), the fire suppression system control will lock out. This feature protects against operation of the tum...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70457901 (EN) 22 Electrical Requirements No independent external power source or supply connection is necessary. Power to operate the 24 Volt fire suppression system is from the rear junction/contactor box. Auxiliary Al...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 23 70457901 (EN) Bolt-On Angle Option 050 Series Tumble Dryers Only This option allows the tumble dryer depth to be reduced to 871 mm (34 5/16 inches). The tumble dryer should then fit through a 914 mm (36 inch) door op...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70457901 (EN) 24 Figure 9 10. Remove the motor(s) and motor bracket(s). Refer to Figure 8 . 11. Unbolt and remove the two vertical trunnion channels. 12. Remove the junction/contactor box. Refer to Figure 8 . 13. Remove...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 27 70457901 (EN) If lockout condition persists, check that the manual gas shut-off valve is in the ON position and that the gas service is properly connected. If condition still persists, remove tumble dryer from servic...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70457901 (EN) 28 Required for CE Models Only Once machine is installed, please be sure to complete the following items:  Review and verify machine operation with customer.  Leave all literature and a signed Declaratio...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 29 70457901 (EN) CE Orifices Properties of CE Gases Gas Type Gas Family Group Gas Designation Supply Pressure Manifold Pressure Capacity/ Model Orifice Diameter (mm) Orifice Part Number Quantity mbar mbar in. wc Natural...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 70457901 (EN) 30 Basic Configuration 1. Determine the necessary conversion operations to convert from the factory-supplied configuration to the desired configuration. 2. Perform the conversions required so the machine i...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 31 70457901 (EN) Figure 16 How to Change Burner Orifice Size 1. Disconnect electrical power from tumble dryer. Close gas shut-off valve to tumble dryer. Refer to Figure 15 . 2. Remove spud holder. Unscrew spud holder nu...

70457901 (EN) 32 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements Layout Whenever possible, install tumble dryers along an outside wall where duct length can be kept to a minimum, and make-up air can be easily accessed. Construction must not block the airflow ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 33 70457901 (EN) NOTE: Exhaust ducts must be constructed of sheet metal or other noncombustible material. Such ducts must be equivalent in strength and corrosion resistance to ducts made of galvanized sheet stee...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 70457901 (EN) 34 Manifold Venting While it is preferable to exhaust tumble dryers individually to the outdoors, a main collector duct may be used if it is sized according to Figure 20 and Figure 21. This illustr...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust Requirements 70457901 (EN) 36 Figure 20 TMB2019N 1 Outlet duct diameter 2 45° typical L K J I H G F E D C B A 2 1 ONE MANIFOLD ASSEMBLY Duct Station 050/075 F75 A 203 mm (8 in.) 254 mm (10 in.) B 305 mm (12 in.) 381 mm (15 i...

70457901 (EN) 38 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Gas Requirements IMPORTANT: Any product revisions or conversions must be made by the Manufacturer’s Authorized Dealers, Distributors or local service personnel. IMPORTANT: The tumble dryer must be isolated from the ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Gas Requirements 39 70457901 (EN) Turn on gas and check all pipe connections (internal and external) for gas leaks with a non-corrosive leak detection fluid. Purge air in gas service line by operating the tumble dryers in the drying...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Gas Requirements 70457901 (EN) 42 High Altitude Burner Orifice Sizing For proper operation at altitudes above 610 m (2000 feet), the gas burner orifice size must be reduced to ensure complete combustion. Refer to Table 7 . For CE mo...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 43 70457901 (EN) Electrical Requirements IMPORTANT: Electrical connections must be made by a qualified electrician using data on serial plate, installation manuals and wiring diagram provided with machine and according to local code...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 70457901 (EN) 44 Grounding Instructions NOTE: To ensure protection against shock, this tumble dryer MUST be electrically grounded in accordance with the local codes, or in the absence of local codes, with the...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 45 70457901 (EN) Service/Ground Location Figure 24 Model Ground and Terminal Block Locations Non-CE CE TMB2269N Terminal Block TMB2269N Ground Electrical Service Junction Box TMB2247N Terminal Block Power Dis...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 70457901 (EN) 46 To Connect Electrical Service To The Tumble Dryer The following steps outline the procedure for connecting the electrical service to the tumble dryer. NOTE: The wiring diagram is located in t...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 47 70457901 (EN) Jumper Configuration Instructions Changing the transformer configuration jumper is required, PRIOR TO SUPPLYING POWER TO THE MACHINE , if any of the following apply: IMPORTANT: Failure to ins...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 70457901 (EN) 48 Electrical Specifications NOTE: Wire sizes were obtained from the Canadian Electrical Code for 75 C. wire and are intended for use as a guideline only. Electrical connections should be made b...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Requirements 49 70457901 (EN) 075 Series Gas and Steam Models Refer to Table 9 and Table 10 . F75 Gas Models Only Serial Plate Rating Terminal Block Connections Required Serial Plate Amps Recommended Circuit Nonreversing ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 51 70457901 (EN) Steam Requirements NOTE: Machines require a constant 5.3 to 6.9 bar (80 to 100 psig) steam service for optimum operation. The maximum allowable steam pressure for use with 50 Hertz tumble dryers is 8.6 bar (125 psig...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Steam Requirements 70457901 (EN) 52 Installing Steam Trap and Making Condensate Return Connections The steam trap must be installed and the coil outlet connections must be connected to the condensate return lines. The following step...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Steam Requirements 53 70457901 (EN) Figure 26 Table 12 TMB2014N NOTE: Refer to Table 12 for sizing of steam lines. Piping must also be sized accordingly for length of runs, and number of elbows. 1 Supply 8 457 mm (18 in.) Drop 2 305...

70457901 (EN) 54 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Single Drop Timer NOTE: The following information is for models with an SD control suffix only. Power-Up Mode When power is applied to the tumble dryer, the IN USE light flashes factory status information. Following...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Single Drop Timer 55 70457901 (EN) Dipswitch Settings Heat Time Per Coin Pulse (in minutes) Heat Switch Number 1 2 3 4 5 6 1 OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF 5 OFF OFF...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Single Drop Timer 70457901 (EN) 56 Models Through Serial No. 0908xxxxx Models Starting Serial No. 0909xxxxx Total Cycle Time = Heat Time + Cool Down Time Table 13 Table 12 (continued) Heat Time Per Coin Pulse (in minutes) Heat Switc...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 57 70457901 (EN) Operating Instructions Emergency Stop Button On CE Models All CE approved OPL tumble dryers are factory equipped with an emergency stop button located on the front panel. Refer to Figure 27 . Figure 27 To operate em...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 58 Step 2: Load Laundry Open loading door and load cylinder with laundry. Maximum drying load for 050 models is 22.7 kg (50 pounds) and for 075 and F75 models is 34 kg (75 pounds). DO NOT OVERLOA...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 59 70457901 (EN) Control Instructions Dual Digital Timer Control QT and RQ Control Suffixes 1. Select HIGH, MED, LOW or NO HEAT by turning the temperature knob. HIGH Temperature 88°C (190°F)MED Temperature 77°...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 61 70457901 (EN) Electronic OPL Micro Control OM and RM Control Suffixes 1. To use an Automatic Cycle, press an ON/ SELECT pad. Select HIGH, MEDIUM, MED LOW, LOW or NO HEAT for items that should not be dried w...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 62 Reversing Operation Tumble Dryers with the reversing option prevent the tangling of large pieces of laundry and minimize wrinkling. These tumble dryers are equipped with a second motor and add...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 63 70457901 (EN) Single Drop Control SD and SX Control Suffixes 1. Select HIGH, MED, LOW or NO HEAT by turning the temperature knob. HIGH Temperature 88°C (190°F)MED Temperature 71°C (160°F)LOW Temperature 54°...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 64 Topoffs Any time the control receives a coin drop pulse during a cycle it will add the programmed dry time to the time currently remaining in the cycle. The maximum cycle time is 99 minutes, t...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 65 70457901 (EN) MDC Coin and Card Control BB, BC, BG, BL, BW, BX, BY and BZ Control Suffixes 1. Select temperature by pressing the appropriate temperature pad. HIGH Temperature 88°C (190°F)MED Temperature 82°...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 66 Quantum Control LB, LC, LW, LX, LY, LZ, WB, WC, WW, WX, WY and WZ Control Suffixes 1. Select HIGH, MED, LOW, NO HEAT or DELICATES by pressing the appropriate temperature pad. HIGH Temperature ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 67 70457901 (EN) Galaxy 600 Control KB, KC, KW, KX, KY and KZ Control Suffixes 1. Select HIGH, MED, LOW or DELICATES by pressing the appropriate temperature pad. HIGH Temperature 88°C (190°F)MED Temperature 82...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 68 LED OPL Control EO and RE Control Suffixes 1. Press the Up (  ) or Down (  ) keypad to change cycles. To customize a cycle, refer to the Programming Manual . 2. Press START ( ) to start sele...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 69 70457901 (EN) UniLinc Control UO and RU Control Suffixes 1. Press the (  ) or (  ) keypad to change cycles. The center highlighted position is the selected cycle. To customize a cycle, refer to the Progra...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 70 DX4 Coin Control 3B, 3V, 3W and 3X Control Suffixes 1. Open door and fill drum with clothes. 2. Close door. 3. Insert the coin(s) in the coin slot. 4. Press and release one of the cycle button...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 71 70457901 (EN) Diagnostic Microprocessor Control General Operation The Diagnostic Microprocessor Control (DMP) is designed to manage the drying and cooling cycles of the tumble dryer. The controller is also ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 72 DMP OPL Models DO and RD Control Suffix Description of the OPL Control Panel Refer to Figure 51 . Figure 51 TMB1956N 1 START. Starts or resumes the current program or cycle. 2 STOP. Temporaril...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 73 70457901 (EN) DMP OPL Features DIP Switch Settings The DMP has an 8 position DIP switch bank that is accessible from the back of the control board. By switching these DIP switches, it is possible for the op...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 74 DMP Coin DV and DX Control Suffixes Description of The Coin Control Panel Refer to Figure 52 . TMB1955N 1 Clock Symbol. This symbol of a clock indicates that the time in the display is countin...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 75 70457901 (EN) DMP Coin Features Coin Keypad Interface - START button to start or resume a cycle. - TEMP button to select HIGH, MEDIUM, or LOW temperature. - Two hidden buttons to increment or decrement the ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 76 Programming 1. Set DIP switch #8 to the ON position. 2. Select the desired program number to change. The LED should be flashing. 3. Select DRY TIME. Set the time with the Up/ Down arrows. 4. S...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 77 70457901 (EN) Rotation Sensor The rotation sensor must “read” the key on the basket shaft or pulley. The sensor must be set approximately 1/4 inch from the key or pulley. Look for the light on the sensor to...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 78 Ignition Control Operation and Troubleshooting for Models Starting 3/11/13 Before troubleshooting the system, check the following items: - Verify all mechanical and electrical connections are ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 79 70457901 (EN) Proper Electrode Location Proper location of the electrode assembly is important for optimal system performance. The electrode assembly should be located so that the tips are inside the flame ...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 81 70457901 (EN) Ignition Control Operation for CE Models Through 3/10/13 Power Up After 24VAC is applied to the ignition control pins 24V and GND, the Diagnostic LED on the ignition control will turn orange/y...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 70457901 (EN) 82 Flame Probe Tests Unexpected Presence of Flame The Unexpected Presence of Flame test is performed when no flame is expected. Failure of this test results in the ignition control entering Locko...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 83 70457901 (EN) Adjustments Gas Burner Air Shutter NOTE: Air inlet shutters on the burner must be adjusted so sufficient air is metered into the system for proper combustion and maximum efficiency. Before adjusting the inlet shutte...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Adjustments 70457901 (EN) 84 Airflow Switch The airflow switch is set at the factory for proper operation. No adjustment necessary. The airflow switch operation may be affected by shipping tape still in place, lack of make-up air, o...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Adjustments 85 70457901 (EN) Loading Door Catch The door catch must be adjusted to have sufficient tension to hold loading door closed against force of load tumbling against it. Proper adjustment is when 0.48-1.03 bar (7-15 pounds) ...

70457901 (EN) 88 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance Daily 1. Inspect the area surrounding tumble dryers, remove all combustible materials, including lint, before operating the machines. 2. Check cylinder for foreign objects to avoid damage to clothing and...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 89 70457901 (EN) Monthly 1. Remove lint and debris from inside exhaust duct to maintain proper airflow and avoid overheating. a. Remove external duct and duct access covers, if present. b. Clean inside of duct with a vac...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 70457901 (EN) 90 Fire Suppression System Maintenance Test To ensure proper operation, the fire suppression system must be tested every three months. If the system test does not perform as indicated: 1. Discontinue use of...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 91 70457901 (EN) 8. Immediately remove and weigh the load. Refer to Table 19 for acceptable weight range. If less than minimum pounds indicated in Table 19 , the fire suppression system has failed the maintenance test. R...

70457901 (EN) 92 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Before You Call for Service Removing Tumble Dryer from Service If the tumble dryer is to be removed from service, perform the following steps where applicable:  Turn off electrical supply external to machine.  Tur...

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 93 70457901 (EN) Disposal of Unit This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This symbol on the product or on its packaging indicates that this produc...