Page 3 - Table of
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT © Copyright 2012, Alliance Laundry Systems LLCAll rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F8221501 1 ...
Page 4 - Introduction; Model Identification; Nameplate Location; Replacement Parts
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8221501 2 Introduction Model Identification Information in this manual is applicable to this model: * This manual applies to models with U3 in the 9th and 10th positions in the model number (e.g. UM202M1OU30001). Nameplate Location...
Page 5 - XXXXXXXXX; amps
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction 3 F8221501 Figure 2 Model Number Familiarization Guide Sample Model Number: UM202M1OU30001 UM Model Number Prefix 202 Washer-Extractor M Type of Electrical Control 1 Washer-Extractor Speed Capability (1 = 1 speed) O Ele...
Page 6 - Safety Information; Explanation of Safety Messages; DANGER
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8221501 4 Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific instructions are found in this manual and on machine decals. These precautions are inten...
Page 7 - NOTE: The WARNING and IMPORTANT
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 5 F8221501 7. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This appliance is not intended for use by young children or infirm...
Page 8 - IMPORTANT: Ensure that the recommended; Safety Decals; WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information F8221501 6 IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked. Safety Decals Safety decals appear at cruci...
Page 9 - Operator Safety; NEVER insert hands or objects into the
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information 7 F8221501 Operator Safety To ensure the safety of machine operators, the following maintenance checks must be performed daily: 1. Prior to operating the machine, verify that all warning signs are present and legi...
Page 10 - Specifications and Dimensions
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8221501 8 Specifications and Dimensions Specification Overall Dimensions Overall width, in. (mm) 60 (1524) Overall depth, in. (mm) 29.5 (749) Overall height, in. (mm) 40 (1016) Weight & Shipping Information Net weight, lb. (kg)...
Page 14 - Installation; Dimensional Clearances; Machine Foundation; Table 3; Machine Anchoring; IMPORTANT: If machine is operated with; To avoid severe personal injury and
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8221501 12 Installation Dimensional Clearances Refer to Figure 5 for recommended dimensional clearances. Figure 5 Machine Foundation The machine may be placed on any level floor as long as floor will hold the weight of the machine....
Page 15 - Electrical Installation; Input Voltage Requirements
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 13 F8221501 Electrical Installation Input Voltage Requirements If a delta supply system is used, the high leg must be connected to the L3 lead at the J-box. NOTE: Rotation of the extractor basket should be clockwise in ...
Page 16 - Grounding; Ensure that a ground wire from a proven
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation F8221501 14 Grounding For personal safety and proper operation, the machine must be grounded in accordance with state and local codes. If such codes are not available, grounding must conform with the National Electric C...
Page 17 - Drain Connection
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 15 F8221501 Drain Connection Figure 6 shows plumbing for UM machines. A flexible connection must be made to a vented drain system to prevent damage to rigid drain pipes. Drain should be vented to ensure proper flow and ...
Page 18 - Water Connection; Figure 8; To prevent personal injury, avoid contact
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation F8221501 16 Water Connection Refer to General Specifications for water supply information.Rigid pipe connections are not recommended.Connections should be supplied by a hot and a cold water line of at least the sizes sh...
Page 19 - Control Function Test
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 17 F8221501 Control Function Test The machine should be cleaned after the installation is complete. A function test should then be executed on the unloaded machine: 1. Check the power supply for correct voltage, phase, ...
Page 20 - Operation; Control Panel
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8221501 18 Operation Control Panel Figure 9 shows the control panel for both standard and car wash top-loading machines. Figure 9 The RUN indicator light indicates a wash cycle is in progress.The WASH timer can be set to up to 15 m...
Page 21 - Operating Instructions; NOTE: Place stringy items such as mop heads in a
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation 19 F8221501 Operating Instructions 1. Turn on the main power source (circuit breaker).2. Close drain of wash compartment to be used. Refer to Figure 10 . Figure 10 3. Select desired temperature and water level. Figure 11 4...
Page 22 - Set wash timer to desired time. Agitation will; NOTE: Place loosely woven washables first, then; NOTE: Each compartment has a 12 pound dry; Operating the machine with severe out-of-
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation F8221501 20 7. Set wash timer to desired time. Agitation will begin when selected water level is reached. Figure 13 8. When cycle is finished, place washables in extract-rinse compartment. Distribute evenly around agitator...
Page 23 - Set extract timer and rinse timer to desired cycle
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation 21 F8221501 10. Set extract timer and rinse timer to desired cycle times. Refer to Figure 15 . Refer to Table 8 for recommended rinse and extract times. Figure 15 11. When cycle is complete, wait until basket stops, then p...
Page 24 - Maintenance; Daily; Sharp edges can cause personal injury.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8221501 22 Maintenance IMPORTANT: Replace all panels that are removed to perform service and maintenance procedures. Do not operate the machine with missing guards or with broken or missing parts. Do not bypass any safety devices. ...
Page 25 - Care of Stainless Steel; CAUTION
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 23 F8221501 Care of Stainless Steel • Remove dirt and grease with detergent and water. Thoroughly rinse and dry after washing. • Avoid contact with dissimilar metals to prevent galvanic corrosion when salty or acidic sol...
