Alliance SWF561*E- Manuals
Alliance SWF561*E– User Manual in PDF format online.
Manuals:
User Manual Alliance SWF561*E
Summary
800168 1 © Copyright 2010, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT T...
2 800168 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 62. Bearing Housing ............................................116 Section 6 –Adjustments 63. Cabinet Leveling Legs ...................................11964. Loading Door .................................................12...
800168 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 1 Safety Information Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,” “WARNING,” and “DANGER”) followed by specific instructions. These precautions are intended for th...
4 800168 Section 1 Safety Information © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exerci...
800168 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Section 2 Introduction Customer Service If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address ...
6 800168 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Model Identification Information in this manual is applicable to these washers. MODEL NUMBER COIN DROP INSTALLED COIN DROP READY CARD READER INSTALLED CARD READER READY HWF561*E1102 X HWF561*H1102 X H...
800168 7 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT How Your Washer Works FLW1651S 3 2 1 COIN DROP MOTOR CONTROL BOARD (Located inside control cabinet) PRESSURE SWITCH (Located inside control cabinet) MIXING VALVE INNER BASKET OUTER TUB MOTOR ELECTRIC ...
8 800168 Section 2 Introduction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT General This frontload washer provides some of the same principles of operation as the typical topload washer. It senses water level, dispenses the desired laundry detergent, agitates the clothes for ...
800168 9 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to e...
10 800168 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 1. TROUBLESHOOTING COIN DROP (continued) Is machine level? (Machines that aren't level may prevent coins from following through required check stages of drop.) No Yes No Refer to wiring diagram fo...
800168 11 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• ...
12 800168 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT (5) Lift spring over left tab. Refer to Figure 5 . (6) Rotate spring clockwise, 40 to 60 degrees, until it is free from right tabs. Refer to Figure 6 . (7) Use screwdriver to remove spring from ce...
800168 13 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• ...
15 800168 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• ...
17 800168 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• ...
18 800168 Section 3 Troubleshooting © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• ...
800168 19 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ...
20 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 6. CANNOT PERFORM INFRARED COMMUNICATION Attempt to communicate with electronic control from Micro-wand. Aim Micro-wand closer and try again. Yes Yes No No Is there any acknowledgemen...
800168 21 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 7. COINS IGNORED WHEN ENTERED Start Coin drop Diagnostic test. Enter several coins Open control panel Check coin drop Make sure control is reset properly and prompting for a vend. No ...
22 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 8. ELECTRONIC CONTROL HAS NO VISIBLE DISPLAY – WASHER Electronic control has no LED or VFD functioning on control board. Plug electronic control washer into electrical outlet. Disconn...
800168 23 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT BRN BLU PNK ORG/BLU T AN/WHT GR Y/BLK RED WHT ORG GRY TAN/WHT YEL/BLK BLK/YEL BLK GR Y/BLK WHT WHT WHT WHT BRN/YEL YEL GRN/YEL RED WHT/BLK BLK/YEL RED/BLK PNK/BLK WHT/RED WHT/BLU RED/...
24 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9. WASHER WILL NOT START (DOOR AND DOOR LOCK SWITCH) – NO DOOR LOCK ONLY Washer will not start (coin inserted) Replace Door Lock Assembly. Replace Door Lock Assembly. Replace Door Loc...
28 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11. WASHER WILL NOT FILL Washer will not fill Change inoperative pressure switch. Yes (1) "AC" (2) "AC" (3) "AC" No Still no voltage. Yes No Is there voltage a...
32 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13. WASHER WILL NOT PUMP Washer will not pump Correct wiring between pump and EDC control board. Check for a kink or blockage in drain hose. Change inoperative EDC control board. Note...
38 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 16. START UP SEQUENCE a. Insert money and/or card and push the button next to the flashing light. b. Both door closed switches need to be in the closed position, after vend price has ...
40 800168 Section 3 Troubleshooting (EDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17. SHUT DOWN SEQUENCE a. Towards end of cycle, “:01” is on display. The door lock actuator is powered down and “K2” relay on EDC control is opened. b. The door lock switch is opened ...
800168 43 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ...
44 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 19. COINS IGNORED WHEN ENTERED Coins Ignored When Entered. Start Coin Drop Diagnostic Test. Refer to programming manual. Reset control to ready mode. Yes No Is "H7" connector ...
46 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20. NO VISIBLE DISPLAY ON CONTROL Control Has No Visible Display The electronic control has no LED or VFD functioning on the control board. Is the power cord plugged in? Plug unit int...
800168 47 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NO VISIBLE DISPLAY ON CONTROL 801182 1 2 3
48 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 21. WASHER WILL NOT START – NO DOOR LOCK Washer Will Not Start. No Door Lock. Washer will not start. Vend satisfied. Is there 120 Volt AC across "H4-5" and "H6-5" on t...
800168 49 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WASHER WILL NOT START – NO DOOR LOCK 801182 5 2 3 1 4
50 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 22. WASHER WILL NOT START – CONTROL ANALYSIS Washer Will Not Start. Control Analysis. Is there 120 Volt AC across "H6-6" to "H6-5" on the control board? (1) Yes No Ref...
800168 51 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WASHER WILL NOT START – CONTROL ANALYSIS 801182 1
52 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 23. WASHER WILL NOT FILL Washer Will Not Fill. Is there 120 Volt AC across the input side of the pressure switch to "FS2" on the motor control board? Correct wiring between pr...
800168 53 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WASHER WILL NOT FILL 801182 1 3 2
54 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 24. WASHER OVERFLOWS Washer Overflows Is there voltage to the over level terminal on pressure switch to "FS2"? Yes No Replace inoperative pressure switch. Is there voltage acr...
800168 55 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WASHER OVERFLOWS 801182 1 2
56 800168 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 25. PUMP DOES NOT OPERATE Pump Does Not Operate Is there voltage across the wht/blk and the white wire going to the motor? Is there voltage across terminals "H6-2" and "H6...
800168 57 Section 3 Troubleshooting (MDC Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT PUMP DOES NOT OPERATE 801182 2 1
800168 61 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ...
62 800168 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 27. MICROWAND DOES NOT COMMUNICATE WITH CONTROL Attempt to communicate with the electronic control from the Microwand. Is there acknowledgement of any kind from the control? Aim...
800168 63 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 28. COINS IGNORED WHEN ENTERED Coins Ignored When Entered. Start Coin Drop Diagnostic Test. Refer to programming manual. Reset control to ready mode. Yes No Is "H7" conn...
64 800168 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29. NO VISIBLE DISPLAY ON CONTROL Control Has No Visible Display The electronic control has no LED or VFD functioning on the control board. Is the power cord plugged in? Plug un...
66 800168 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 30. WASHER WILL NOT START – NO DOOR LOCK Washer Will Not Start. No Door Lock. Washer will not start. Vend satisfied. Is there 120 Volt AC across "H4-5" and "H6-5"...
68 800168 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 31. WASHER WILL NOT START – CONTROL ANALYSIS Washer Will Not Start. Control Analysis. Is there 120 Volt AC across "H6-6" to "H6-5" on the control board? (1) Yes ...
70 800168 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 32. WASHER WILL NOT FILL Washer Will Not Fill. Is there 120 Volt AC across the input side of the pressure switch to "FS2" on the motor control board? Correct wiring betw...
74 800168 Section 3 Troubleshooting (NetMaster Models) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 34. PUMP DOES NOT OPERATE Pump Does Not Operate Is there voltage across the wht/blk and the white wire going to the motor? Is there voltage across terminals "H6-2" and &...
800168 79 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ...
80 800168 Section 4 Grounding To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires mus...
800168 83 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ...
84 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
800168 85 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
86 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
92 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
800168 93 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
800168 95 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
96 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
800168 97 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground ...
100 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
800168 103 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
104 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
800168 105 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
106 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
800168 107 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
108 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
110 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
112 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
800168 113 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
114 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
116 800168 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
800168 117 Section 5 Service Procedures To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground...
800168 119 To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires must be reconnected to...
120 800168 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
800168 121 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
122 800168 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
123 800168 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
124 800168 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
125 800168 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
126 800168 Section 6 Adjustments To reduce the risk of electric shock, fire, explosion, serious injury or death:• Disconnect electric power to the washer before servicing.• Never start the washer with any guards/panels removed.• Whenever ground wires are removed during servicing, these ground wires ...
Alliance Manuals
-
Alliance AWN432SP113TW01
User Manual
-
Alliance AWN432SP113TW01
Installation Manual
-
Alliance AWN542SP111TW01
User Manual
-
Alliance AWN542SP111TW01
Installation Manual
-
Alliance AWN412SP111TW01
User Manual
-
Alliance AWN412SP111TW01
Installation Manual
-
Alliance ATE50FGP171TW01
User Manual
-
Alliance ATE50FGP171TW01
Installation Manual
-
Alliance AWN432SP111TW01
User Manual
-
Alliance AWN432SP111TW01
Installation Manual
-
Alliance ATG50FGP111TW01
User Manual
-
Alliance ATG50FGP111TW01
Installation Manual
-
Alliance AWN311SP111TW01
User Manual
-
Alliance AWN311SP111TW01
Installation Manual
-
Alliance AWNE82SP113TW01
User Manual
-
Alliance AWNE82SP113TW01
Installation Manual
-
Alliance AWN432SP113TW04
User Manual
-
Alliance AWN432SP113TW04
Installation Manual
-
Alliance AWN43RSN115TW01
User Manual
-
Alliance AWN43RSN115TW01
Installation Manual