Page 3 - this machine according to the; WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 1 NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are fac...
Page 4 - Table of
© Copyright 2012, Alliance Laundry Systems LLCAll rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 2 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT ...
Page 6 - Model Identification
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 4 Model Identification Information in this manual is applicable to these machine models: HCD020JD2 SCL030JC2 SCL040JC2 SCL060JC2 SCU080JCF SCL020JC2 SCL030JCF SCL040JD2 SCL060JCF SCU080JCV SCL020JD2 SCL030JD2 SCL040JDF SCL0...
Page 7 - Preliminary Information; About the Control; Glossary of Terms; Infra-red Communications
5 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Preliminary Information About the Control This control is an advanced, programmable computer that lets the owner control most machine features by pressing a sequence of keypads. Refer to Figure 1 . The control allows the ...
Page 8 - Control Identification; Select Cycle Pads
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 6 Control Identification Select Cycle Pads Refer to Figure 1. Select Cycle pads are used to select the specific machine cycle. These pads include NORMAL/90C, NORMAL/60C, NORMAL/40C, PERM PRESS/90C, PERM PRESS/60C, PERM PRES...
Page 9 - Display Identification
7 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Display Identification Light Emitting Diodes (LEDs) Refer to Figure 1. Light Emitting Diodes (LEDs) are used to indicate the chosen cycle, cycle status, if vend is needed, when the bleach compartment is dispensing, and do...
Page 10 - Machine Operation
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 8 Machine Operation Start Up When power is applied to the machine, the control will display its software version as “ S xx ” (“xx” is the version number) for one second. If the control was not powered down during a running ...
Page 11 - Signals; Changing Cycles
Machine Operation 9 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Signals There are five options when a signal can be used during the machine operation. These five options are listed below: 1. End of Cycle Signal By default, this signal is turned off. If turned on, the...
Page 12 - Special Features; NOTE: Additional audit information is retrievable
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 10 Special Features Programming Control The control allows the machine owner to program the control with the use of the keypad. Cycle and vend options may be programmed, audit information may be viewed and diagnostic tests ...
Page 13 - Top Cover and Coin Vault Openings; OPL Mode
Special Features 11 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Top Cover and Coin Vault Openings The control will capture the times and dates of the openings of the Coin Vault and the Top Cover. The information is saved in memory. An open top cover combined with var...
Page 14 - Opening the Top Cover
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 12 Opening the Top Cover To manually program the control, the top cover must be opened. Opening and closing the top cover trips a switch which allows access to various programming options. Once opened, the top cover may eit...
Page 15 - Entering the Manual Mode; How to Enter the Manual Mode; NOTE: The coin vault switch must be closed to; Manual Programming
13 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Entering the Manual Mode For programming, testing, and retrieving information from the control, it is often necessary to enter the Manual Mode by following the six simple steps below. How to Enter the Manual Mode 1. If a...
Page 16 - What Can Be Programmed?; NOTE: The letters and numbers in the Option; Programmable Options Available
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 14 Programming Control What Can Be Programmed? This feature allows the owner to program cycle information, standard vend pricing, special vends and other features by using the keypads. The control must have the Manual Progr...
Page 21 - Programming Flowcharts; Entering Manual Mode
Programming Control 19 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Flowcharts Entering Manual Mode > > > > “rAPd” - Quickly advance through active cycles. 1. Press START (enter) keypad to begin Rapid Advance cycle and advance through cycle ste...
Page 27 - Diagnostic
Programming Control 25 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Diagnostic CHM1402R “dIAg” - Diagnostic Tests. 1. Press START (enter) keypad. “d021” - Water Leak Detection Test “Ld” “d020” - Water Purge Test “PUrg” “d019” - Drive DC Bus Display Test “dCb” (Design ...
Page 28 - How to Exit Programming Feature
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 26 1. Normal/90C Vend Price “AtS1” This option allows the owner to set the vend price for a NORMAL/90C wash. This vend price will be shown in the display when NORMAL/90C is selected. How to Program the N...
Page 29 - How to Program Coin #1 Value; “dEn2”
Programming Control 27 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2. Coin #1 Value “dEn1” This option allows the owner to set a specific numerical value for a coin entered. For example, in the United States the coin value for one quarter would be measured in cents (...
Page 30 - How to Program Coin #2 Value; “PLSE”
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 28 3. Coin #2 Value “dEn2” This option allows the owner to set a specific numerical value for a coin entered when using the dual coin drop. For example, the coin value for a dollar coin would be measured...
Page 31 - Start Pulse Value “PLSE”; How to Program Start Pulse Value; “PLSn”
Programming Control 29 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 4. Start Pulse Value “PLSE” This option allows the owner to program the value of the Start Pulse if used for multiple pulses with an after- market central card reader or pay system. Refer to option 5 ...
Page 32 - Start Pulse Mode “PLSn”; How to Program Start Pulse Mode; NOTE: To go back to the current programmable; . To program other options, refer to the
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 30 5. Start Pulse Mode “PLSn” This option allows the owner to program the Start Pulse Input. The Start Pulse Mode can be used for after-market central pay or card systems. The central system sends the st...
Page 33 - Available Type “AtyP”; How to Program Available Type; to
Programming Control 31 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 6. Available Type “AtyP” This option allows the owner to program when the control provides an available output for card and central pay systems. How to Program Available Type 1. Control must be in Man...
Page 34 - Default Cycle “dCYC”; How to Program Default Cycle; “oPL”; Table 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 32 7. Default Cycle “dCYC” This option allows the owner to set the default cycle and temperature the machine will enter when in the Ready Mode. When programming the default cycle, refer to Table 4 . How ...
Page 35 - “AUd”
Programming Control 33 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 8. OPL Mode Enable/Disable“oPL” This option allows the owner to enable or disable the OPL Mode in which no vend price needs to be satisfied to operate the machine. How to Program the OPL Mode Enable/D...
Page 36 - Audio Signal “AUd”; How to Program the Audio Signal; “CArd”
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 34 9. Audio Signal “AUd” This option allows the owner to program when the signal will sound.There are five occasions when a signal may sound during operation. These five occasions are listed below: 1. En...
Page 37 - How to Read
Programming Control 35 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT How to Read Table 5 To determine the correct number required to program the Audio Signal, use the following chart. The Signal Value column contains the number required in step 6. The other columns cor...
Page 38 - Card Reader Display Control; NOTE: This feature does not need to be; other options, refer to the appropriate section.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 36 10. Card Reader Display Control “CArd” This option allows the owner to program whether the display is controlled by the machine’s electronic control or by the card reader. NOTE: This feature does not ...
Page 39 - How to Program Error Code Programming; and refer to
Programming Control 37 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11. Error Code Programming “Err-” This option allows the owner to turn on or turn off certain errors in the control. How to Program Error Code Programming 1. Control must be in Manual Mode. Refer to E...
Page 43 - How to Enter Cycle Programming; “AgIt”; continue to next Cycle Programming option. To
Programming Control 41 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 12. Cycle Programming “CyC-” This option allows the owner to program different aspects for various steps in each type of cycle. There are nine cycles available for programming. How to Enter Cycle Prog...
Page 44 - How to Program Cycle Segment “SEg1”; Programming Segment Enable/Disable; Programming Fill Step; FLEn; “SUPL”
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 42 How to Program Cycle Segment “SEg1” There are eight programmable cycle segments. Within each segment, there are several programmable options. 1. Press the NORMAL/40C ( ) or the PERM PRESS/40C ( ) keyp...
Page 45 - Programming Supply Step; SUEn; “AgSt”
Programming Control 43 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Supply Step 1. When “ SUPL ” appears in the display, press the START (enter) keypad. The first Supply step programming option will appear in the display. 2. Press the NORMAL/40C ( ) or the...
Page 46 - Programming Agitate Step; AgEn; Programming Drain Step; “SPIn”
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 44 Programming Agitate Step 1. When “ AgSt ” appears in the display, press the START (enter) keypad. The first Agitate step programming option will appear in the display. 2. Press the NORMAL/40C ( ) or t...
Page 47 - Programming Extract Step; SPEn
Programming Control 45 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Extract Step 1. When “ SPIn ” appears in the display, press the START (enter) keypad. The first Extract step programming option will appear in the display. 2. Press the NORMAL/40C ( ) or t...
Page 48 - How to Program Cycle Time “Cnin”; PCtd
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 46 How to Program Cycle Time “Cnin” This option allows the owner to add minutes to the cycles display time. 1. Press the NORMAL/40C ( ) or the PERM PRESS/40C ( ) keypad to scroll through the programmable...
Page 49 - “bALr”; Number of Balance Retries; “IrA”
Programming Control 47 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13. Supply/Compartment Dispenser Programming “SUPC” (Design 1 Models Only) This option allows the owner to choose between the supply dispenser or compartment dispenser. NOTE: Supply Dispenser must onl...
Page 50 - “t FC”; “FH”
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 48 15. IR Access (Enabled/Disabled) “IrA” This option allows the owner to enable or disable allowing the control to be read by an external device. How to Program the IR Access (Enabled/Disabled) 1. Contr...
Page 51 - Hot Water Temperature “FH”; How to Program Hot Water Temperature; Warm Water Temperature; How to Program Warm Water Temperature
Programming Control 49 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17. Hot Water Temperature “FH” This option allows the owner to program the hot water temperature for models equipped with heat. How to Program Hot Water Temperature 1. Control must be in Manual Mode. ...
Page 52 - Cold Water Temperature “FC”; How to Program Cold Water Temperature; Codn; “PtEn”; To prevent personal injury, avoid contact
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 50 19. Cold Water Temperature “FC” This option allows the owner to program the cold water temperature for models equipped with heat. How to Program Cold Water Temperature 1. Control must be in Manual Mod...
Page 53 - “rAEn”; Manual Rapid Advance; “nCtd”
Programming Control 51 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 21. Production Test Cycle (Enabled/ Disabled) “PtEn” This option allows the owner to enable or disable access to the production test cycle. Refer to Production Test Cycle section for more information....
Page 54 - No Cycle Time Display “nCtd”; How to Program No Cycle Time Display; “PCtd”; Programmable Cycle Time
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 52 23. No Cycle Time Display “nCtd” This option allows the owner to enable or disable whether the cycle time will appear in the display. How to Program No Cycle Time Display 1. Control must be in Manual ...
Page 55 - Slow Drain Detection Adjust; NOTE: The Slow Drain Detection Adjust Value can; options, refer to the appropriate section.
Programming Control 53 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 25. Slow Drain Detection Adjust Value “SdAd” This option allows the owner to increase the Slow Drain Detection threshold by adding additional seconds to the threshold value. When enabled, it increases...
Page 64 - How to Program the Time and Date; NOTE: The hours will be displayed in military
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 62 35. Set Real-Time Clock “rtC-” This option allows the owner to set the control’s internal clock to the correct time and date. How to Program the Time and Date 1. Control must be in Manual Mode. Refer ...
Page 65 - (Special Vend A Start
Programming Control 63 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 36. Special Vend A Data “SPA-” This option allows the owner to set the day or days of a special vend.Special Vend A is used to change the standard vend prices for special occasions. The special vend c...
Page 70 - Length in Hours), continue to next Special Vend A
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 68 How to Program Special Vend A Start Hour “SA02” This option allows the owner to set the hour that Special Vend A will begin, from 0-23. 1. Press the NORMAL/40C ( ) or the PERM PRESS/40C ( ) keypad to ...
Page 72 - (Special Vend A End
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 70 How to Program Special Vend A Start Date “SA06” This option allows the owner to set the date that Special Vend A will begin, from 1-31. 1. Press the NORMAL/40C ( ) or the PERM PRESS/40C ( ) keypad to ...
Page 73 - Vend A option. To program other options, press the
Programming Control 71 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT How to Program Special Vend A End Date “SA09” This option allows the owner to set the date that Special Vend A will end, from 1-31. 1. Press the NORMAL/40C ( ) or the PERM PRESS/40C ( ) keypad to scro...
Page 74 - fifth digit is “
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 72 How to Program Special Vend A Normal/90C Vend Price “SA11” This option allows the owner to set the vend price for a NORMAL/90C wash in Special Vend A. The corresponding LED will be lit while programmi...
Page 83 - “FLo”
Programming Control 81 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT How to Program Special Vend A Wash Agitate Step Added Minutes “SA20” This option allows the owner to add time to the wash agitate part of the cycle in Special Vend A. 1. Press the NORMAL/40C ( ) or th...
Page 84 - Low Water Level “FLo”; How to Program Low Water Level; FnEd; Medium Water Level “FnEd”; How to Program Medium Water Level; FHI
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 82 37. Low Water Level “FLo” This option allows the owner to program the low water level during fill and tumble of all cycles. How to Program Low Water Level 1. Control must be in Manual Mode. Refer to E...
Page 85 - High Water Level “FHI”; How to Program High Water Level; NOTE: The High Water Level value can be set
Programming Control 83 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 39. High Water Level “FHI” This option allows the owner to program the high water level during fill and tumble of all cycles. How to Program High Water Level 1. Control must be in Manual Mode. Refer t...
Page 86 - refer to the appropriate section.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Control F8238301 84 5. When the desired option appears in the display, press the START (enter) keypad. The current value will appear in the display. 6. Press the NORMAL/40C ( ) or the PERM PRESS/40C ( ) keypad to enable ...
Page 87 - Collecting Audit Information; How to Enter Audit Feature; How to Read Audit Data; How to Exit Audit Feature
85 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Collecting Audit Information This feature allows the owner to retrieve audit information stored in the machine by pressing a sequence of pads on the control. For an explanation of the audit options available, refer to Ta...
Page 88 - Manual Reset; How to Enter Manual Reset
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 86 Manual Reset This feature allows the owner to reset the machine control’s programming data to the factory default settings by pressing a sequence of pads on the control. For an explanation of the Factory Default Settings...
Page 89 - Testing Machine and; How to Enter Diagnostic Testing Feature; How to Start Tests
87 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Testing Machine and Electronic Control Functions This feature allows the owner to run diagnostic tests on various machine operations without servicing the machine. The following tests are available: • Balance Weight Test...
Page 90 - Water Purge Test
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Testing Machine and Electronic Control Functions F8238301 88 VFD Balance Weight Test (Design 1 Models) This test is only available on machines equipped with a variable frequency motor drive.To start test, control must be in the Diag...
Page 91 - To Enter Production Test Cycle
Testing Machine and Electronic Control Functions 89 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Drive Software Version Number Test (Design 2 models only) This option displays the custom drive software version number. To start test, control must be in the Diagnostic T...
Page 94 - Error Codes
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 92 Error Codes Following is a list of possible error codes for an electronic control. Errors beginning with “EI” refer to external device Infra-red communication errors. Errors beginning with “EC” refer to card reader error...
Page 98 - Rapid Advance Feature; How to Enter Rapid Advance; NOTE: Door must be closed to start cycle.; How to Use Rapid Advance; NOTE: The Rapid Advance option must be turned
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 96 Rapid Advance Feature The Rapid Advance feature allows the owner to quickly advance through active cycles or advance into a cycle from the ready mode. How to Enter Rapid Advance 1. If control is in Ready Mode, control mu...
Page 99 - Clear Vend Feature; How to Clear Vend
97 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Clear Vend Feature The Clear Vend feature allows the owner to clear a control which is in the middle of satisfying a vend price, and set it back to the Ready Mode. How to Clear Vend 1. Open the top cover. Refer to Openin...
Page 100 - Power Fail Recovery
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 98 Power Fail Recovery The Power Fail Recovery feature allows the cycle status to be saved in memory in the event of a power failure.If the power failure lasted less than 2 minutes, the cycle will resume without requiring t...
Page 101 - Communications Mode; NOTE: The Infra-red Communications option
99 F8238301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Communications Mode Infra-red Communications The Infra-red Communications feature allows the control to communicate with an external device. The control can be programmed and have its data read without using the keypad. ...
Page 102 - Default Cycles
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8238301 100 Default Cycles Cycle Chart Cycle Steps Normal/ 90C Normal/ 60C Normal/ 40C Perm Press/ 90C Perm Press/ 60C Perm Press/ 40C Perm Press/ 70C Perm Press/ 50C Delicate/ 30C Cycle reference (display in Program Mode) CYC1 CYC...
Alliance AWN432SP113TW01
User Manual
Alliance ATE50FGP171TW01
User Manual
Alliance AWNE82SP113TW01
User Manual
Alliance AWN432SP113TW04
User Manual
Alliance AWN43RSN115TW01
User Manual