Alliance PHM1397C- Manuals

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Safety Information F8112101 6 Operator Safety To ensure the safety of machine operators, the following maintenance checks must be performed daily: 1. Prior to operating machine, verify that all warning signs are present and l...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Safety Information 7 F8112101 • Water Damage . Do not spray machine with water. Short circuiting and serious damage may result. Repair immediately all seepage due to worn or damaged gaskets, etc. Machine Location • Foundation...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Safety Information F8112101 8 DirectDrive Machines equipped with DirectDrive require special attention with regard to operating environment. • An especially dusty or linty environment will require more frequent cleaning of AC...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Safety Information 9 F8112101 Model Identification Information in this manual is applicable to these models: Medium Speed High Speed 40 Pound CP040PMNCP040PMQCP040PMXCPC40MIP040PMN IP040PMQIP040PMXIPH40MIPH180 CP040PHNCP040PH...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 10 F8112101 Introduction This manual is designed as a guide for the installation of a washer-extractor equipped with DirectDrive. NOTE: All information, illustrations and specifications contained in this manual are based on t...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 11 F8112101 Specifications and Dimensions High Speed Models . Models Specifications 40H 60H 80H 100H 125H 140H 175H Overall Dimensions Overall Width, in. (mm) 32 (813) 34.5 (876) 42.5 (1080) 42.5 (1080) 56.3 (1430) 56.3 (1430...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 13 F8112101 Medium Speed Models . Models Specifications 40M 60M 80M 100M 140M Overall Dimensions Overall Width, in. (mm) 32 (813) 34.5 (876) 42 (1080) 42.5 (1080) 50.3 (1276) Overall Height, in. ...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 15 F8112101 Machine Dimensions Dimensional Clearances Allow 24 inches (600 mm) at the rear of the machine and 18 inches (450 mm) is recommended at the sides for maintenance, inspection and adjust...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 16 40 Pound Models PHM727N 1 External Supply Connection 6 External Supply Wiring Connection 2 Auxiliary 7 Power Inlet 3 Hot Water 8 Steam Inlet 4 Cold Water 9 Auxiliary Drain 5 Greasing ...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 17 F8112101 60 Pound Models PHM728N 1 External Supply Connection 6 External Supply Wiring Connection 2 Auxiliary 7 Power Inlet 3 Hot Water 8 Auxiliary Drain 4 Cold Water 9 Drain 5 Greasing Points...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 18 80 Pound Models PHM729N 1 External Supply Connection 6 External Supply Wiring Connection 2 Auxiliary 7 Power Inlet 3 Hot Water 8 Auxiliary Drain 4 Cold Water 9 3 in. (76.2 mm) Drain 5...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 23 F8112101 Front and Rear Features PHM687N 1 Front Service Panel 9 Chemical Service Connection 2 Door Release Panel 10 Water Service Connections 3 Door Handle 11 Lubrication Points for Bearings ...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 24 See next two pages for Floor Load Data

© Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or T R ANSMIT S p ecif icat ions an d Dimens ions 25 F81 1 2 101 Floor Load Data Machine Size Basket Diameter Net Wt. of Machine (lbs.) Height of Basket Center (in.) Max RPM G Calculated Static Load (lbs.) Static Floor Pressure (lbs./ft. 2 ) D...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 27 F8112101 Installation Instructions Surface These machines must be securely anchored on a solid, flat reinforced concrete surface capable of withstanding the weight of the machine and the consi...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 29 F8112101 IMPORTANT: If the machines are to be mounted less than 18 in. (457 mm) from each other or less than 18 in. (457 mm) from a side wall, only the inside bolt holes will be accessible. If...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 30 Installing Anchors 1. Before installing anchor bolts, measure holes to verify that they match bolt hole pattern in base of frame. 2. Clean out anchor holes and floor around them. 3. I...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 37 F8112101 Water Connection In order for machine to function properly, water service should have the following: • Separate hot and cold lines with individual shut-off valves. • Hot water tempera...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 38 Drain Connection Requirements A drain system of adequate capacity is essential to washer-extractor performance. Ideally, water should empty through a vented pipe directly into a sump ...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions 39 F8112101 Electrical Installation Requirements IMPORTANT: Electrical ratings are subject to change. Refer to serial decal for electrical ratings information specific to your machine. Electrical...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 40 The AC drive provides thermal overload protection for the drive motor. However, a separate circuit breaker or electrical supply disconnecting device must be installed for complete ele...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 42 Making Connections to Machine After electrical service feeder has been installed and electrical service voltage verified by a volt meter, follow this procedure to connect service to t...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT Specifications and Dimensions F8112101 44 Chemical Injection Supply System Undiluted chemical dripping can damage the washer-extractor. Therefore, all chemical supply dispenser pumps should be mounted below the washer’s injec...

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 45 F8112101 Figure 21 Connection of Chemical Pump Signals To connect pump control to AC voltage signals, do the following: 1. Remove large rear electrical module cover on machine to access chemical terminals. 2. Mount pump sy...