Advantech PPC-V106 - Manuals

Page 2 - Copyright

PPC-V106 User Manual ii Copyright This document is copyrighted, © 2004. All rights are reserved. The origi-nal manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.No part of this manual may be reproduced, copied, translated or tran...

Page 3 - FCC Class B

iii FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence when the equipment is operated in a residential environment....

Page 4 - Packing List

PPC-V106 User Manual iv Packing List Before you begin installing your card, please make sure that the following materials have been shipped:• PPC-V106 series panel PC• Accessories for PPC-V106 - Warranty card- Power cord: For AC Model: US type AC power cord.For DC Model: DC power inlet cable (180cm)...

Page 5 - Additional Information and Assistance

v Additional Information and Assistance Step 1. Visit the Advantech web site at www.advantech.com or www.advantech.com.tw where you can find the latest informa- tion about the product. Step 2. Contact your distributor, sales representative, or Advantech's cus- tomer service center for technical supp...

Page 6 - Safety Instructions

PPC-V106 User Manual vi Safety Instructions 1. Read these safety instructions carefully.2. Keep this User's Manual for later reference.3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the ...

Page 7 - Wichtige Sicherheishinweise

vii Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.2. Heben Sie diese Anleitung für den späteren Gebrauch auf.3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch z...

Page 9 - Contents; Chapter

ix Table of Contents Contents Chapter 1 General Information ........................................2 1.1 Introduction ....................................................................... 2 1.2 General Specifications....................................................... 2 1.3 LCD Specifications ...

Page 13 - General Information

CHAP T ER 1 General Information This chapter gives background information on the PPC-V106 panel PC.Sections include: • Introduction• General Specifications• LCD Specifications• Dimensions

Page 14 - Chapter 1 General Information; General Specifications; General

PPC-V106 User Manual 2 Chapter 1 General Information 1.1 Introduction PPC-V106 is fanless and comes with a VIA Eden low-power CPU for higher reliability and performance. The ruggedized aluminum enclosure without ventilation holes makes PPC-V106 waterproof and dust proof.A variable power source suits...

Page 15 - PCI bus master IDE interface:

3 Chapter 1 Standard PC functions• CPU: Embedded VIA Eden 800 MHz CPU • BIOS: Award 256 KB Flash BIOS, supports Plug & Play, APM • System Chipset: VIA CLE266 and VT8235 CD • Front side bus: 133 MHz • System Memory: Two 184-pin DIMM sockets, accepts up to 2 GB DDR 266 SDRAM • PCI bus master IDE i...

Page 17 - LCD Specifications

5 Chapter 1 Environment • Operating Temperature: 0 ~ 45° C (32 ~ 122° F) • Storage Temperature: -20 ~ 60° C • Relative Humidity: 10 ~ 95% @ 40° C (non-condensing) • Shock: 10 G peak acceleration (11 msec duration) • Certifications: EMC: CE, FCC. Safety: UL1950. • Vibration: 5 ~ 500 Hz 1 G RMS Random...

Page 19 - System Setup

CHAP T ER 2 System Setup This chapter details system setup on the PPC-V106 Panel PC.Sections include: • A Quick Tour of the Panel PC• Installation procedures• Running the BIOS Setup Program

Page 20 - Chapter 2 System Setup; A Quick Tour of the Panel PC

PPC-V106 User Manual 8 Chapter 2 System Setup 2.1 A Quick Tour of the Panel PC Before you start to set up the panel PC, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below.When you place the panel ...

Page 22 - Installation Procedures

PPC-V106 User Manual 10 2.2 Installation Procedures 2.2.1 Connecting the Power Cord There are two kinds of power supplies for the PPC-V106 series, AC and DC.For AC model : The Panel PC can only be powered by an AC electrical outlet (100 ~ 250 volts, 50 ~ 60 Hz). Be sure to always handle the power co...

Page 23 - Running the BIOS Setup Program

11 Chapter 2 2.3 Running the BIOS Setup Program Your panel PC is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the panel PC's BIOS (Basic Input-Output System) setup program to change system configuration information, such ...

Page 24 - Installing System Software

PPC-V106 User Manual 12 2.4 Installing System Software Recent releases of operating systems from major vendors include setup programs which load automatically and guide you through hard disk preparation and operating system installation. The guidelines below will help you determine the steps necessa...

Page 25 - Installing the Drivers

13 Chapter 2 2.5 Installing the Drivers After installing your system software, you will be able to set up the Ether-net, SVGA, audio, and touchscreen functions. All the drivers except the CD-ROM drive driver are stored in a CD-ROM disc entitled "Drivers and Utilities." The CD-ROM drive drive...

Page 28 - Overview of Hardware Installation and Upgrading

PPC-V106 User Manual 16 Chapter 3 Hardware and Peripheral Installation 3.1 Overview of Hardware Installation and Upgrading The panel PC consists of a PC-based computer that is housed in a rugge-dized aluminum enclosure. Any maintenance or hardware upgrades can be completed after removing both panels...

Page 29 - Placing the Rubber Seal

17 Chapter 3 2. Place the HDD inside the HDD bracket and tighten four screws (#1) from both sides of the HDD bracket. 3. The HDD cable (1 x 44-pin to 1 x 44-pin) is next to the HDD bracket. Connect the HDD cable to the HDD. Make sure that the red wire corresponds to Pin 1 on the connector, which is ...

Page 30 - Installing the Universal Arm

PPC-V106 User Manual 18 3.4 Installing the Universal Arm 1. Press latches at the same time and then rotate support-1 until you can see both of the screw holes. 2. Rotate support-2 until the angle is the same as support-1. 3. Use four M4x8L screws and attach the U-Arm with the PPC-V106. The 4 stainle...

Page 32 - Chapter 4 Jumper Settings and Connectors

PPC-V106 User Manual 20 Chapter 4 Jumper Settings and Connectors 4.1 Setting Jumpers You can configure your panel PC to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by...

Page 35 - CPU Installation

23 Chapter 4 4.1.4 Locating Connectors Figure 4.2: Locating Connectors on the PPC-V106 Motherboard 4.2 CPU Installation The CPU is embedded on the motherboard, so there are no settings for frequency ratio or voltage.

Page 41 - VIA Chipset

CHAP T ER 5 VIA Chipset This chapter provides information on Intel chipset configuration • Introduction• Further information

Page 42 - Chapter 5 VIA Chipset; Further Information

PPC-V106 User Manual 30 Chapter 5 VIA Chipset 5.1 Introduction The PPC-V106 uses the combination of VIA CLE266 north bridge and VT8235 CD south bridge.The VIA CLE266 chipset is an innovative integrated graphics chipset developed with DDR266 memory and optimized to support the VIA C3 and VIA Eden Ser...

Page 43 - AGP SVGA Setup

CHAP T ER 6 AGP SVGA Setup • Introduction• Installation of SVGA Driver - for Windows 98/ME - for Windows 2000/XP • Further Information

Page 44 - Chapter 6 AGP SVGA Setup; Installation of SVGA Driver

PPC-V106 User Manual 32 Chapter 6 AGP SVGA Setup 6.1 Introduction The PPC-V106 has an onboard integrated VGA chipset The specifica-tions and features are described as follows: 6.1.1 Chipset The VIA CLE266 boasts a complete integrated VIA 128-bit 2D/3D graphics engine with a high quality video proces...

Page 45 - Further Information

33 Chapter 6 6.2.1 Installation for Windows 98/ME 1. Click the 'Start' button in the task bar, click 'Run' and then select 'Setup.exe' from D:\PPC-S154\845G Graphics Driver\WIN9X_ME\Setup.exe. The Install dialog will appear. 2. Click 'Next' to continue. 3. Read License Agreement and click "Yes&#...

Page 47 - PCI Bus Ethernet Interface

CHAP T ER 7 PCI Bus Ethernet Interface This chapter provides information on Ethernet configuration. • Introduction• Installation of Ethernet Driver - for Windows 98/ME- for Windows 2000/XP • Further Information

Page 48 - Chapter 7 PCI Bus Ethernet Interface; Installation of Ethernet Driver

PPC-V106 User Manual 36 Chapter 7 PCI Bus Ethernet Interface 7.1 Introduction The PPC-V106 is equipped with a high performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T an...

Page 50 - Further Information

PPC-V106 User Manual 38 7.3 Further Information Realtek website: www.realtek.com.twAdvantech website: www.advantech.com

Page 51 - Audio

2 CHAP T ER 8 Audio • Introduction• Installation of Audio Driver

Page 52 - Chapter 8 Audio; Installation of Audio Driver

PPC-V106 User Manual 40 Chapter 8 Audio 8.1 Introduction The ALC202 is an 18-bit, full duplex AC'97 2.2 compatible stereo audio CODEC designed for PC multimedia systems, including host/soft audio and AMR/CNR based designs. The ALC202 AC'97 CODEC supports multiple CODEC extensions with independent va...

Page 54 - Driver Installation for Windows XP

PPC-V106 User Manual 42 Chapter 9 USB 2.0 9.1 Installation of USB 2.0 Driver Before installing the audio driver, please take note of the procedures detailed below. You must know which operating system you are using in your PPC-V106, and then refer to the corresponding installation proce-dure 9.2 Dri...

Page 55 - Driver Installation for Windows 2000

43 Chapter 9 9.3 Driver Installation for Windows 2000 1. Install Service Pack 3 or above before running the setup program. 2. Open the Device Manager and check if there is a “Universal Serial Bus (USB) Controller” under “Other devices”. 3. Execute the setup program by double click on the “SETUP.exe”...

Page 56 - Further Information

PPC-V106 User Manual 44 9.4 Driver Installation for Windows ME / 98 / 98SE 1. Open the Device Manager and check if there is a yellow exclama-tion mark on any one of the “VIA Tech 3038 PCI to USB Universal Host Controller” items. 2. Execute the setup program by double click on the “SETUP.exe” file in...

Page 57 - Touchscreen

CHAP T ER 10 Touchscreen • Introduction• Installation of Touchscreen Drivers- for Windows 98/ME - for Windows 2000/XP

Page 58 - Chapter 10 Touchscreen

PPC-V106 User Manual 46 Chapter 10 Touchscreen 10.1 Introduction 10.1.1 General information There are two kinds of touch screens for the PPC-V106 series, one is resistive touch screens, the other for infrared touch screens.The resistive touch screen incorporates advanced second-generation resistive,...

Page 59 - Installation of Touchscreen Drivers

47 Chapter 10 10.1.3 Environmental Specifications Chemical resistance: The active area of the resistive touchscreen is resis-tant to the following chemicals when exposed for a period of one hour at a temperature of 21° C (71° F):Acetone, Methylene chloride, Methyl ethyl ketone, Isopropyl alcohol, He...

Page 61 - Further Information

49 Chapter 10 10.2.2 Installation of Resistive T/S driver for Windows 2000/XP To install the software to PPC-V106, your PPC-V106 must have Win-dows 2000/XP system running and installed PenMount Series Interface control board already. If you have an older version of PenMount Win-dows 2000/XP driver i...

Page 64 - Appendix A Programming the Watchdog Timer; A.1 Programming the Watchdog Timer

PPC-V106 User Manual 52 Appendix A Programming the Watchdog Timer A.1 Programming the Watchdog Timer To program the watchdog timer, you must write a program which writes I/O port address 440 (hex). The output data is a time interval value. The value range is from 01 (hex) to 3F (hex), and the relate...

Page 67 - Pin Assignments

Appendix B Pin Assignments This appendix contains information on PPC-V106’s pin assignments.

Page 68 - Appendix B Pin Assignments

PPC-V106 User Manual 56 Appendix B Pin Assignments B.1 Inverter Power Connector (CN10) B.2 Internal Speaker Connector (CN14) Table B.1: Inverter power connector (CN10) Pin Signal 1 +12V 2 GND 3 ENAVEE 4 VBR 5 +5 V Table B.2: Internal speaker connector (CN14) Pin Signal 1 Speaker out_L - 2 Speaker ou...