Page 2 - Copyright notice
Copyright notice This document is copyrighted, 2000. All rights are reserved. Theoriginal manufacturer reserves the right to make improvements to theproducts described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated ortransmitted in any form or...
Page 3 - Acknowledgments; Business Machines Corporation.
Acknowledgments AMD is a trademark of Advanced Micro Devices, Inc.Award is a trademark of Award Software International, Inc.Cyrix is a trademark of Cyrix Corporation.IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation. Intel, Celeron, Pentium and Pentium II are tra...
Page 4 - Packing list; • 1 CD disc with utility and drivers
Packing list Before you begin installing your card, please make sure that thefollowing materials have been shipped: • 1 PCM-9570/S all-in-one single board computer • 1 CD disc with utility and drivers • 1 Startup Manual If any of these items are missing or damaged, contact your distributoror sales r...
Page 5 - Contents
Contents Chapter 1 General Information ....................... 1 1.1 Introduction ........................................................................ 2Highly integrated Socket 370 SBC ...................................... 2 1.2 Features ............................................................
Page 8 - Chapter 6 SCSI Setup and Configurations .. 59; Basic rules for SCSI host adapter and device; Appendix A Programming the Watchdog
Chapter 6 SCSI Setup and Configurations .. 59 6.1 Introduction ...................................................................... 60 6.2 Before you begin ............................................................... 61 6.3 Basic rules for SCSI host adapter and device installation ................
Page 10 - Tables
Tables Table 2-1: Jumpers .............................................................................. 8Table 2-2: Connectors ......................................................................... 9Table 2-3: CMOS clear (J1) ............................................................... 15Tabl...
Page 12 - Figures
Figures Figure 1-1: PCM-9570/S dimensions ................................................... 6Figure 2-1: Locating jumpers ............................................................. 10Figure 2-2: Locating connectors (component side) ............................ 11Figure 2-3: Locating connectors ...
Page 13 - General Information; • Introduction
General Information This chapter gives background information onthe PCM-9570/S. Sections include: • Introduction • Features • Specifications • Board layout and dimensions CHAPTER 1
Page 14 - Introduction; III level single; Highly integrated Socket 370 SBC; Celeron; III processors, making the
2 PCM-9570/S User's Manual 1.1 Introduction The PCM-9570/S is an all-in-one Celeron™/Pentium ® III level single board computer (SBC) with an Ultra2 SCSI controller (PCM-9570S),a 2x AGP LCD controller, a PCI Fast Ethernet interface and one PCIexpansion slot. With the Intel Celeron TM processor, the P...
Page 15 - Ultra2 SCSI interface:; Standard SBC functions; Enhanced IDE interface:
Chapter 1 General Information 3 1.2 Features • Ultra2 SCSI interface: Supports up to 80 MB/sec transfer rates (PCM-9570S only) • 3D VGA/LCD interface: Supports a 2x AGP interface, 3D 64-bit engine, as well as a 2.5 MB embedded Trident 9525 DVD chip • Display resolution: Up to 1024 x 768 @ 64 K color...
Page 16 - PCI SVGA/flat panel interface
4 PCM-9570/S User's Manual • Serial ports: Four serial ports with +5 V / +12 V power capability (COM1, 3, 4: RS-232; and COM2: RS-232/422/485) • Watchdog timer: Software enabled/disabled. 62-level interval from 1 to 62 seconds. Jumperless selection. Generates system resetor IRQ11 • Keyboard/mouse co...
Page 17 - PCI bus Ethernet interface
Chapter 1 General Information 5 PCI bus Ethernet interface • Chipset: Realtek RTL8139 PCI-bus Ethernet controller • Ethernet interface: PCI 100/10 Mbps, IEEE 802.3U compatible • Remote boot ROM: For diskless system Ultra2 SCSI (PCM-9570S only) • Chipset: SYM 53C895 chips • Performance: Ultra2 SCSI i...
Page 18 - Board layout and dimensions
6 PCM-9570/S User's Manual 1.4 Board layout and dimensions F i g u r e 1 - 1 : P C M - 9 5 7 0 / S d i m e n s i o n s
Page 19 - Installation
Installation This chapter tells how to set up thePCM-9570/S hardware, including instructionson setting jumpers and connecting peripherals,switches and indicators. Be sure to read all thesafety precautions before you begin theinstallation procedure. CHAPTER 2
Page 20 - Jumpers
8 PCM-9570/S User's Manual 2.1 Jumpers The PCM-9570/S has a number of jumpers that allow you toconfigure your system to suit your application. The table below liststhe function of each of the board’s jumpers: Ta b l e 2 - 1 : J u m p e r s Label Function J1 CMOS clear J2 Watchdog timer action J3 SCS...
Page 21 - Connectors; Please refer to Appendix C for pin assignments.
Chapter 2 Installation 9 2.2 Connectors On-board connectors link the PCM-9570/S to external devices such ashard disk drives, a keyboard, or floppy drives. The table below lists thefunction of each of the board’s connectors: Table 2-2: Connectors Label Function CN1 Ethernet 100/10Base-T connector CN2...
Page 22 - Locating jumpers
10 PCM-9570/S User's Manual 2.3 Locating jumpers F i g u r e 2 - 1 : L o c a t i n g j u m p e r s
Page 23 - Locating connectors
Chapter 2 Installation 11 2.4 Locating connectors 2.4.1 Component side F i g u r e 2 - 2 : L o c a t i n g c o n n e c t o r s ( c o m p o n e n t s i d e )
Page 25 - Setting jumpers
Chapter 2 Installation 13 2.5 Setting jumpers You configure your card to match the needs of your application bysetting jumpers. A jumper is the simplest kind of electric switch. Itconsists of two metal pins and a small metal clip (often protected by aplastic cover) that slides over the pins to conne...
Page 26 - CPU installation and upgrading; Warning! Always disconnect the power cord from your chassis; Make sure the ZIF socket lever is in the upright position. To raise
14 PCM-9570/S User's Manual 2.6 CPU installation and upgrading You can upgrade to a higher power Pentium processor at any time.Simply remove the old CPU, install the new one, and set the jumpersfor the new CPU type and speed. Warning! Always disconnect the power cord from your chassis when you are w...
Page 27 - To avoid damaging the computer, always turn off the
Chapter 2 Installation 15 When the CPU is installed, the lever should snap into place at the sideof the socket. Note: To remove a CPU, pull the lever out to the side a littleand raise it as far as it will go. Lift out the CPU chip. 2.6.2 CMOS clear (J1) Warning: To avoid damaging the computer, alway...
Page 29 - Wire number 1 on the cable is red or blue, and the other wires are gray.
Chapter 2 Installation 17 2.8.1 Connecting the hard drive Connecting drives is done in a daisy-chain fashion and requires one oftwo cables (not included in this packing), depending on the drive size.1.8" and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector.3.5" drives use...
Page 31 - alternatives to this specification do not overload the card.
Chapter 2 Installation 19 2.11 Keyboard and PS/2 mouse connector (CN5) The PCM-9570/S board provides a keyboard connector that supportsboth a keyboard and a PS/2 style mouse. In most cases, especially inembedded applications, a keyboard is not used. The standard PC/ATBIOS will report an error or fai...
Page 32 - Supplies secondary power to devices that require -5 V and -12 V.
20 PCM-9570/S User's Manual 2.12.4 Reset switch If you install a reset switch, it should be an open single pole switch.Momentarily pressing the switch will activate a reset. The switchshould be rated for 10 mA, 5 V. If you need to make your own cable, you can find the pin assignmentsfor the board’s ...
Page 33 - Impor tant: Be sure that the ATX power supply can take at least
Chapter 2 Installation 21 2.14 ATX power control connector (CN2, J4) 2.14.1 ATX feature connector (CN2) and power button (J4) The PCM-9570/S can support an advanced power button if an ATXpower supply is used. To enable the power button: 1. Take the specially designed optional ATX-to-PS/2 power cable...
Page 34 - cannot boot up without ATX power switch button J4.
22 PCM-9570/S User's Manual 2.15 ATX power on function select (J11) T a b l e 2 - 5 : A T W p o w e r o n f u n c t i o n s e l e c t ( J 11 ) Default on Default off * J11 * default setting Note1: J11 select 1-2, that while AC power is turned on, the system cannot boot up without ATX power switchbut...
Page 38 - VGA interface connections
26 PCM-9570/S User's Manual 2.18 VGA interface connections The PCM-9570/S’s PCI SVGA interface can drive conventional CRTdisplays and is capable of driving a wide range of flat panel displays,including electroluminescent (EL), gas plasma, passive LCD andactive LCD displays. The board has two connect...
Page 39 - If the Pin 1 of SW1 is in the ON position, the LCD is
Chapter 2 Installation 27 2.18.4 Panel type select (SW1) SW1 is a 6-pin dip switch for selecting the type of panel and displaymode. Table 2-12: Panel type select (SW1) Panel type Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 TFT 640 x 480 18-bit OFF ON ON ON ON - TFT 800 x 600 18-bit OFF OFF ON ON ON - TFT 10...
Page 40 - Ethernet configuration
28 PCM-9570/S User's Manual 2.19 Ethernet configuration The PCM-9570/S is equipped with a high performance 32-bit PCI-busEthernet interface which is fully compliant with IEEE 802.3U10/100Mbps CSMA/CD standards. It is supported by all majornetwork operating systems. The medium type can be configured ...
Page 41 - Watchdog timer configuration; The USB interfaces can be disabled in the system BIOS setup.
Chapter 2 Installation 29 2.20 Watchdog timer configuration An on-board watchdog timer reduces the chance of disruptions whichEMP (electro-magnetic pulse) interference can cause. This is aninvaluable protective device for standalone or unmanned applications.Setup involves one jumper and running the ...
Page 45 - Ethernet software configuration; file is located in the working drive.
Chapter 3 Software Configuration 33 3.2 Ethernet software configuration The PCM-9570/S’s on-board Ethernet interface supports all majornetwork operating systems. To configure the medium type, to view thecurrent configuration, or to run diagnostics, do the following: 1. Power the PCM-9570/S on. Make ...
Page 47 - Award BIOS Setup
Award BIOS Setup This chapter describes how to set BIOSconfiguration data. CHAPTER 4
Page 48 - System test and initialization; You are starting your system for the first time
36 PCM-9570/S User's Manual 4.1 System test and initialization These routines test and initialize board hardware. If the routinesencounter an error during the tests, you will either hear a few shortbeeps or see an error message on the screen. There are two kinds oferrors: fatal and non-fatal. The sy...
Page 49 - Award BIOS setup
Chapter 4 Award BIOS Setup 37 4.2 Award BIOS setup Award’s BIOS ROM has a built-in Setup program that allows users tomodify the basic system configuration. This type of information isstored in battery-backed CMOS RAM so that it retains the Setupinformation when the power is turned off. 4.2.1 Enterin...
Page 57 - If the CMOS is bad or this option has never been used, a default
Chapter 4 Award BIOS Setup 45 4.2.9 Change password To change the password, choose the PASSWORD SETTING optionform the Setup main menu and press <Enter>. 1. If the CMOS is bad or this option has never been used, a default password is stored in the ROM. The screen will display thefollowing mess...
Page 59 - PCI SVGA Setup
PCI SVGA Setup • Introduction • Installation of SVGA driver for - Windows 95 - Windows 98 - Windows NT CHAPTER 5
Page 61 - To set up dual display under Windows 98, follow these steps:
Chapter 5 PCI SVGA Setup 49 5.1.4 Dual/simultaneous display The PCM-9570/S uses a Trident Cyber 9525DVD LCD controller thatis capable of providing multiple views and simultaneous display withmixed video and graphics on a flat panel and CRT. To set up dual display under Windows 98, follow these steps...
Page 62 - Installation of SVGA driver; Impor tant: The following windows illustrations are examples
50 PCM-9570/S User's Manual 5.2 Installation of SVGA driver Complete the following steps to install the SVGA driver. Follow theprocedures in the flow chart that apply to the operating system thatyou are using within your PCM-9570/S. Impor tant: The following windows illustrations are examples only. ...
Page 69 - Further information
Chapter 5 PCI SVGA Setup 57 5.3 Further information For further information about the PCI/SVGA installation in yourPCM-9570/S, including driver updates, troubleshooting guides andFAQ lists, visit the following web resources: Trident website: www.trid.com Advantech websites: www.advantech.com www.adv...
Page 73 - Before you begin
Chapter 6 SCSI Setup and Configurations 61 6.2 Before you begin SDMS software requires an IBM PC/AT or compatible computer withan 80486 or higher microprocessor. An understanding of basicoperating system commands is assumed. In addition, users shouldhave a general knowledge of the SCSI standard. Bef...
Page 74 - Configuring the SCSI adapter
62 PCM-9570/S User's Manual 6.4 Configuring the SCSI adapter Access the SCSI BIOS by holding down both the CTRL and C keyswhen you see the BIOS banner message listing the driver name andthe attached devices. For example: Symbios Inc. SDMS (TM) V 4.0 PCI SCSI BIOS PCI Rev. 2.0, 2.1 Copyright 1995, 19...
Page 75 - SCSI terminators; • By default, termination on the CPU card itself is automatic (the
Chapter 6 SCSI Setup and Configurations 63 6.5 SCSI terminators To ensure reliable communication, the SCSI bus must be properlyterminated. Termination is controlled by a set of electrical resistors,called terminators. Terminators must be placed (or enabled) at the twoextreme ends of the SCSI bus. Al...
Page 76 - SDMS drivers
64 PCM-9570/S User's Manual 6.6 SDMS drivers The SDMS device drivers translate an operating system I/O requestinto a SCSI request. Each Symbios SCSI device driver is operatingsystem specific and is designed to work on standard Symbios chipimplementations. We provide PCI SDMS device drivers for the f...
Page 79 - Other tools and utilities:; Driver and utility installation; For SCO Unix and Solaris:
Chapter 6 SCSI Setup and Configurations 67 Other tools and utilities: • BIOS.HTM: User's guide for SCSI BIOS configuration utility • FLASH.HTM: SDMS host adapter Flash utility • FORMAT.HTM: SDMS SCSI low-level format utility • RAWRITE.HTM: Description of RaWrite 1.3 • UTILMAIN.HTM: SDMS utilities us...
Page 82 - Then choose the correct driver to install in your panel PC.
70 PCM-9570/S User's Manual 7.1 Introduction The PCM-9570/S is equipped with a high performance 32-bitEthernet chipset which is fully compliant with IEEE 802.3 100 MbpsCSMA/CD standards. It is supported by major network operatingsystems. It is also both 100Base-T and 10Base-T compatible. Themedium t...
Page 90 - A.1 Programming the watchdog timer
78 PCM-9570/S User's Manual A.1 Programming the watchdog timer In order to program the watchdog timer, you must write a programwhich writes I/O port address 443 (hex). The output data is a value oftime interval. The value range is from 01(hex) to 3E(hex), and therelated time interval is 1 sec. to 62...
Page 97 - Pin Assignments
Pin Assignments This appendix contains information of adetailed or specialized nature. It includes: • Ethernet 10/100Base-T connector • ATX power feature connector • SCSI connector • Keyboard and PS/2 mouse connector • Main power connector • IR connector • Floppy drive connector • IDE hard drive con...
Page 110 - C.15 LCD signal mapping
9 8 PCM-9570/S User's Manual Pin Name LCD 16-bit DSTN 18-bit TFT 24-bit TFT 36-bit TFT PD0 LD0 R5 R7 Ro5 PD1 LD1 R4 R6 Ro4 PD2 LD2 R3 R5 Ro3 PD3 LD3 R2 R4 Ro2 PD4 LD4 G5 G7 Go5 PD5 LD5 G4 G6 Go4 PD6 LD6 G3 G5 Go3 PD7 LD7 G2 G4 Go2 PD8 UD0 B5 B7 Bo5 PD9 UD1 B4 B6 Bo4 PD10 UD2 B3 B5 Bo3 PD11 UD3 B2 B4...
Page 117 - System Assignments; • 1st MB memory map
System Assignments • System I/O ports • 1st MB memory map • DMA channel assignments • Interrupt assignments D APPENDIX
Page 119 - D.2 1st MB memory map; * If Ethernet boot ROM is enabled; D.3 DMA channel assignments
Appendix D System Assignments 107 D.2 1st MB memory map Ta b l e D - 2 : 1 s t M B m e m o r y m a p Addr. range (Hex) Device F000h - FFFFh System ROM E000h - EFFFh Unused D000h - DFFFh SCSI ROM *CC00h - CFFFh Ethernet ROM C000h - CBFFh Expansion ROM B800h - BFFFh CGA/EGA/VGA text B000h - B7FFh Unus...
Page 120 - D.4 IRQ mapping chart
1 0 8 PCM-9570/S User's Manual D.4 IRQ mapping chart Table D-4: IRQ mapping chart 0 Interval timer 1 Keyboard 2 Interrupt from Controller 2 3 COM2 4 COM1 5 COM4 6 FDD 7 LPT1 8 RTC 9 Reserved 10 COM3 11 Reserved (watchdog timer) 12 PS/2 mouse 13 INT from co-processor 14 Primar y IDE 15 Secondary IDE ...
Page 121 - Optional Extras
Page 125 - Mechanical Drawings
Page 126 - Component side
114 PCM-9570/S User's Manual F.1 Component side F i g u r e F - 1 : P C M - 9 5 7 0 / S m e c h a n i c a l d r a w i n g - c o m p o n e n t s i d e
Page 127 - Solder side
Appendix F Mechanical Drawings 115 F.2 Solder side F i g u r e F - 2 : P C M - 9 5 7 0 / S m e c h a n i c a l d r a w i n g - s o l d e r s i d e
Advantech PCM-3350 Series
Manual
Advantech PCL-849
Manual
Advantech EKI-2525P
Manual
Advantech PCA-6275
Manual
Advantech USB-4761
Manual
Advantech HMI-640S
Manual
Advantech 4718
Manual
Advantech SOM-4450 ETX
Manual
Advantech PCA-6774
Manual
Advantech SPC-57
Manual
Advantech UNO-1170
Manual
Advantech PPC-155T
Manual
Advantech TPC-1260
Manual
Advantech Touch Panel Computers
Manual
Advantech RMD-1150
Manual
Advantech PPC-120
Manual