ADTRAN QFO-C - Manuals

ADTRAN QFO-C – Manual in PDF format online.

Manuals:

Manual

Manual ADTRAN QFO-C

Summary

Page 2 - C A U T I O N !; Table 2. QFO-only Populated Total Access Chassis; Warranty and Customer Service; Compliance Codes; Table 1. Compliance Codes; Wiring

2 Section 61181300L1-5C, Issue 3 61181300L1-5C • Installs in both the Total Access 3000 (23-inch) and the Total Access (19-inch) chassis. • End-to-end transmission for one to four DS1 circuits • Operating wavelength 1310 nm • Single mode fiber operation • Power budget of 25dB (typical) • Launch powe...

Page 4 - N O T E

4 Section 61181300L1-5C, Issue 3 61181300L1-5C If the system is configured with only QFO-Cs, all fourDSX-1 connections are made. The connections aremade via four Amphenol connectors to Pair 5 throughPair 8 on the backplane. Table 5. Pin-out For Pair 5 and 7 on TA 3010 r o l o C p u o r G r e d n i B...

Page 5 - Figure 2. Total Access 3000 CO Chassis

61181300L1-5C Section 61181300L1-5C, Issue 3 5 If no protection switching is provided, the Main unitplugs into any odd-numbered slot. The next highereven-numbered slot may contain a blank card or canbe left empty. See Figure 2 . Installing the QFO-C 1. Set the right switch segment S2-2 to Working “o...

Page 6 - Figure 3. Fiber Optic Receiver Cabling; Fiber Optic Transceiver

6 Section 61181300L1-5C, Issue 3 61181300L1-5C Release the card retention lever and carefully seatthe card into the backplane connector by firmlypressing on the QFO-C front panel. Verify thefiber cables move freely between the cable guidesand the shelf. When installed and powered, the PWR LED (green...

Page 9 - Figure 4

61181300L1-5C Section 61181300L1-5C, Issue 3 9 • ESCAPE – press the switch in the MODE direction and release it between 1.5 seconds and3 seconds to ascend the menu tree. • ROOT - press the switch in the MODE direction and release it after 3 seconds to return to the firstelement of the Level 1 card m...

Page 11 - Laser degrade signal

61181300L1-5C Section 61181300L1-5C, Issue 3 11 Table 9. QFO-C Menu Hierarchy QFO-C Main Menu ConfigurationProvisioning Service State Port 0/1/2/3/4 All Provisioning DSX EqualizationLoop Back TimeoutAIS to DSX (Loss of T1)AIS to DSX (FLOS)Restore Factory Defaults Status Port 1/2/3/4All Ports Alarms ...

Page 12 - Entering the Fiber Main Menu Screen; Figure 5. Fiber Main Menu Screen

12 Section 61181300L1-5C, Issue 3 61181300L1-5C Shelf: Slot: 10 Total Access System 07/15/99 10:37Unacknowledged Alarms: MINOR QFO-C Main Menu 1. Configuration 2. Provisioning 3. Status 4. Alarms 5. Test 6. Performance Monitoring 7. Protection Switching 8. Circuit Id Selection: ‘?’ - System Help Scr...

Page 13 - Accessing the QFO-C Provisioning Screen

61181300L1-5C Section 61181300L1-5C, Issue 3 13 Figure 8. Service State Screen Shelf: Slot: 10 Total Access System 07/15/99 10:42Unacknowledged Alarms: None Service State 1. Port 0 Out of Service - Unassigned 2. Port 1 Out of Service - Unassigned 3. Port 2 Out of Service - Unassigned 4. Port 3 Out o...

Page 14 - Figure 10. Provisioning of All Ports Screen; Port 0 is the QFO-C access module itself.; Changing the Port Service State; Figure 9. Port Service Status Screen

14 Section 61181300L1-5C, Issue 3 61181300L1-5C Figure 10. Provisioning of All Ports Screen Shelf: Slot: 10 Total Access System 07/15/99 10:45Unacknowledged Alarms: MINOR Provisioning for All Ports 1. DSX Equalization 0 to 133' ABAM 2. Loopback Timeout 120 Min. 3. AIS to DSX (Loss of T1) Disabled 4....

Page 15 - Figure 11. DSX Equalization Screen

61181300L1-5C Section 61181300L1-5C, Issue 3 15 N O T E Port 0 (all ports) “Out of Service” disables theentire module. Port 0 must be “In Service” forany Port 1 to 4 to be active. Changing the DSX Equalization 1. From the Provisioning of All Ports screen, type “1”and press Enter to select DSX Equali...

Page 17 - Restore Factory Default Settings

61181300L1-5C Section 61181300L1-5C, Issue 3 17 Figure 15. Restore Factory Defaults Screen Shelf: Slot: 10 Total Access System 07/15/99 10:43Unacknowledged Alarms: None Restore Factory Defaults? 1. No 2. Yes Selection: ‘?’ - System Help Screen Figure 16. Status Screen Shelf: 1 Slot: 5 Total Access S...

Page 18 - Figure 18. Status of All Ports Screen; Viewing the Status of a Single Port; Figure 17. Port Status Screen

18 Section 61181300L1-5C, Issue 3 61181300L1-5C Shelf: Slot: 10 Total Access System 07/15/99 10:43Unacknowledged Alarms: None Status of All Ports Near End Far End Fiber Loss No No Laser Bias Alarm No No Adjacent Card Present N/A On Line No No Switched Manually No No RT Auto Mode No No Port 1 Disable...

Page 19 - Figure 20. Alarm Reporting Screen; Accessing the Alarms Screen; Figure 19. Alarms Screen

61181300L1-5C Section 61181300L1-5C, Issue 3 19 Shelf: Slot: Total Access System 02/18/98 02:24:18 Unacknowledged Alarm: None Alarms Level––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– QFO-C Fiber LOS from Facility Major QFO-C Laser Bias Minor QFO-R Discretionary Minor ? -...

Page 20 - Changing Alarm Settings and Thresholds; number of desired setting and press Enter.; Figure 21. Alarm Provisioning Screen; Alarm Provisioning

20 Section 61181300L1-5C, Issue 3 61181300L1-5C Shelf: Slot: Total Access System 02:24:18 02/18/98 Unacknowledged Alarm: None ES Threshold (15 Min.): 30 1. 302. 150 Selection: ? - System Help Screen Figure 22. ES Threshold (15-Minute) Screen Changing Alarm Settings and Thresholds 1. From the QFO-C M...

Page 21 - Type number of desired setting and press Enter.

61181300L1-5C Section 61181300L1-5C, Issue 3 21 Figure 24. UAS Threshold (15-Minute) Screen Shelf: Slot: Total Access System 02/18/98 02:24:18 Unacknowledged Alarms: None UAS Threshold (15 Min.): 15 1. 15 2. 75 Selection: ‘?’ - System Help Screen Figure 23. SES Threshold (15-Minute) Screen SHELF: SL...

Page 22 - number of the desired setting and press Enter.

22 Section 61181300L1-5C, Issue 3 61181300L1-5C Figure 25. ES Threshold (24-Hour) Shelf: Slot: Total Access System 02:24:18 02/18/98 Unacknowledged Alarm: None ES Threshold (24 Hour): 14400 1. 28802. 14400 Selection: ? - System Help Screen Figure 26. SES Threshold (24-Hour) Shelf: 3 Slot: 11 Total A...

Page 23 - Figure 28. Test Screen; Setting Up Loopbacks for a Test

61181300L1-5C Section 61181300L1-5C, Issue 3 23 Figure 28. Test Screen Shelf: Slot: Total Access System 02/18/98 02:24:18 Unacknowledged Alarms: None Test 1. Port 1 Loopback 2. Port 2 Loopback 3. Port 3 Loopback 4. Port 4 Loopback Selection: ‘?’ - System Help Screen Figure 27. UAS Alarm Threshold (2...

Page 24 - Figure 29. Port Test Screen; Loopback RT: Disabled; Figure 30. Loopback RT Screen; Performing Loopback Testing; displays the Loopback

24 Section 61181300L1-5C, Issue 3 61181300L1-5C Figure 29. Port Test Screen Shelf: Slot: Total Access System 02:24:18 02/18/98 Unacknowledged Alarms: None Loopback RT: Disabled 1. Disabled2. Network3. Dual Selection: ‘?’ - System Help Screen Figure 30. Loopback RT Screen Shelf: Slot: Total Access Sy...

Page 25 - Figure 32. Performance Monitoring Screen; shows the Loopback DSX Screen. Type; Loopback DSX: Disabled; Figure 31. Loopback DSX Screen

61181300L1-5C Section 61181300L1-5C, Issue 3 25 Figure 32. Performance Monitoring Screen Shelf: Slot: Total Access System 02:24:18 02/18/98 Unacknowledged Alarms: None Peformance Monitoring 1. Port 1 (Near End) 2. Port 2 (Near End) 3. Port 3 (Near End) 4. Port 4 (Near End) 5. Port 1 (Far End) 6. Por...

Page 26 - Figure 34. Protection Switch Screen; Viewing Performance Monitoring Screens; Figure 33. Port Performance Monitoring Screen

26 Section 61181300L1-5C, Issue 3 61181300L1-5C Shelf: Slot: Total Access System 02/18/98 02:24:18 Unacknowledged Alarms: None APS Switching 1. ACT Activate Selection: ‘?’ - System Help Screen Figure 34. Protection Switch Screen Viewing Performance Monitoring Screens Type the number corresponding to...

Page 27 - Figure 36. Circuit ID Screen; Setting the Port Circuit ID; Figure 35. Protection Switch Activate Screen

61181300L1-5C Section 61181300L1-5C, Issue 3 27 Shelf: Slot: Total Access System 02/18/98 02:24:18 Unacknowledged Alarms: None Circuit ID 1. Port 1 2. Port 2 3. Port 3 4. Port 4 Selection: ‘?’ - System Help Screen Figure 36. Circuit ID Screen 2. Type “2” and press Enter to switch the WorkingQFO-C to...

Page 28 - WARRANTY AND CUSTOMER SERVICE; document; ADTRAN Sales; Figure 37. Port Current Circuit ID Screen

28 Section 61181300L1-5C, Issue 3 61181300L1-5C 2. Type the number of the corresponding port whoseCircuit ID is to be set or changed and press Enter. ThePort Current Circuit ID Screen (Figure 37) will display. 3. Type the new Circuit ID and press Enter. 4. MAINTENANCE The QFO-C requires no routine m...

Page 29 - ANSI X3T9.5 Fiber Distributed Data Interface

61181300L1-5C Section 61181300L1-5C, Issue 3 29 Table 10. QFO-C Specifications DS1 Input Level .............................................................. 0 to -9 dBm Output Level ........................................................... 0 dB with DSX buildout from 0 to 655 ft. in 133 ft. incre...