Page 3 - Safety precautions and maintenance; Important Safety Instructions
Safety precautions and maintenance WARNING: Use of control, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Important Safety Instructions Important Safety Instructions Read and follow these inst...
Page 6 - Use
Use • Don’t turn the ventilation hole of Power Box upside down. As shown in the picture below. The ventilation hole of power box 6 It is prohibited to place tilt The ventilation hole of power box It is prohibited to turn the ventilation hole of Power Box upside down.
Page 8 - Remote Controller Precautions:; Two sides brightness level only be controlled by front side OSD
Use Remote Controller Precautions: • This product requires remote switch (ON/OFF) from Front Side ; the Back Side only has OSD function operated by remote controller. • Two sides brightness level only be controlled by front side OSD simultaneously , won’t be separate to control the brightness level....
Page 9 - Installation Notes
Installation Notes F 9 There have 8 use holes on the side of the display set (M4x15mm)
Page 11 - Unpacking
Package Content Package Content Unpacking • This product is packed in a carton, together with the standard accessories. • Due to the size and weight of this display it is recommended for two people to move it. • After opening the carton, ensure that the contents are complete and in good condition. 1...
Page 12 - Accessories; Dual Side Display x1
Accessories Dual Side Display x1 PC Box x1 ( with 24V&12V line) 12 Dual Side Display x1 ( with 24V&12V line) Remote Controller x1 (Battery : CR 2025 3V) Power Cord x3 (EUx1, USx1, UKx1)
Page 13 - Over View; Front View
Over View Front View Top View Diagonal View 13 Side View
Page 15 - Step1 : Putting the dual side display upside
Setting Up The Display Setting Up The Display Step1 : Putting the dual side display upside 15 While the display put upside , the screw will be seen on the left.
Page 16 - Step2 : Remove the three I/O covers on the sides
Step2 : Remove the three I/O covers on the sides 16 Remove I/O cover screws x 3(M3x6mm)
Page 17 - Step3 : Remove the downside cover
Step3 : Remove the downside cover Tear down the downside cover. screws x 10(M3x6mm) 17 screws x 10(M3x6mm)
Page 18 - Step4 : Connect Power Box to Dual Side Display; Power Box; Red line
Step4 : Connect Power Box to Dual Side Display 24V*1 Red line 2 18 Power Box Dual Side Display Red line (10 pin) 12V*1 Yellow line (8 pin) 1
Page 19 - Yellow line
Connect the 24V (10 pin) power line 1 Connect the 12V (8 pin) power line 2 Step4 : Connect Power Box to Dual Side Display 19 12V*1 Yellow line (8 pin) 24V*1 Red line (10 pin) 1 2
Page 20 - Step5 : Connect by HDMI connector
Step5 : Connect by HDMI connector Plug two HDMI cables into the cabinet.And ensure that all cable plugs are firmly fitted to the equipment jacks. 20 HDMI HDMI Front Side (700 nits) Back Side (700 nits)
Page 21 - Reinstall the downside
Step6 : Reinstall the downside cover and I/O covers Reinstall the downside 21 1 Reinstall the downside cover. screws x 10(M6x30mm) Reinstall the other two I/O covers which are not use. 2
Page 22 - Step7 : Connect the power cord
AC in / switch AC in / switch AC in / switch AC in / switch Step7 : Connect the power cord Power Box 22 Plug in the power cable and turn on the AC power switch.
Page 23 - Step8: Using the Remote Control; Key; Into OSD module; Exit
Step8: Using the Remote Control 1 2 3 4 5 23 No. Key Descriptions Power Power on/Power off Menu Into OSD module Menu Up Menu Down Exit Menu/Exit selection 1 3 2 4 5
Page 24 - OSD Setting Menu; Luminance
OSD Setting Menu Press “MENU” into the OSD Setting Menu, and then press “UP” or “DOWN” to select the item, at last press “EXIT” to leave menu : 24 Luminance Press MENU to select one of the following, and then press “UP” or “DOWN” to select the desired level, ---Brightness1: Range: 0~100 ; Default : ...
Page 25 - Color
Press “MENU” into the OSD Setting Menu, and then press “UP” or “DOWN” to select the item, at last press “EXIT” to leave menu : 25 Color Press MENU to select one of the following, and then press “UP” or “DOWN” to select the desired level, ---Color Temperature: Range: 6500K, 9300K, 11500K, User Define...
Page 27 - Setup
Press “MENU” into the OSD Setting Menu, and then press “UP” or “DOWN” to select the item, at last press “EXIT” to leave menu : 27 Setup Press MENU to select one of the following, and then press “UP” or “DOWN” to select the item , ---Language: English / Español / Français / Deutsch / Italiano / Portu...
