3Com 4007R - Manuals

4 Quick Installation Guide Unpacking Instructions Follow these steps: 1 Place the chassis shipping box near the rack, the table, or the shelf where you plan to install the chassis. WARNING: Safety regulations state that the selected table, shelf, or rack must be able to support at least three times ...

Quick Installation Guide 5 Figure 3 Contents of the Switch 4007R Chassis Shipping Box CD-ROM Switch 4007 Plastic feet 6-32 screws 10-32 screws Rack-mount clips Documentation 1000XXXX HARD WARE KIT Plastic bag for hardware kit Plastic label bezel 2 Mounting shelves Chassis Top Chassis Bottom Pre-inst...

6 Quick Installation Guide 4 Remove the top foam packing material (Figure 4). Figure 4 Removing the Chassis Shipping Box 5 On the outside of the shipping box on the skid, cut the shipping bands. 6 Remove the corrugated sleeve by pulling it straight up (Figure 4). The 8-slot chassis is shipped with m...

Quick Installation Guide 7 Figure 5 The Switch 4007R 8-slot Chassis is Shipped with These Slots Empty After you receive the chassis, remove the faceplate from power supply slot 3 to help make chassis installation easier. See step 8 in this section. 7 While the 8-slot chassis is still in the base of ...

8 Quick Installation Guide shelf that you plan to use. To help you hold onto the 8-slot chassis when you lift it, you can place one hand into the empty power supply slot 3. The other person places one hand into empty power supply slot 1. 10 Inspect the chassis for damage. If the chassis appears to b...

Quick Installation Guide 9 WARNING: Safety regulations state that the selected table, shelf, or rack must be able to support at least three times the weight of a fully loaded chassis. ■ A fully loaded 8-slot chassis weighs approximately 71.7 kg (158 lb). Therefore, the selected table, shelf, or rack...

10 Quick Installation Guide and the 12 screws (from the hardware kit) available when you begin to install the chassis. ■ For a tabletop or shelf installation, make certain that you have a Phillips screwdriver or flat-blade screwdriver and the hardware kit available. Before you attempt to mount the c...

Quick Installation Guide 11 3 To help support the chassis while you install it in a rack, install the mounting shelves that are shipped with your chassis. If you install more than one chassis in a rack, install the bottom chassis first. Make certain that there is sufficient space between the bottom ...

12 Quick Installation Guide Figure 7 Preinstalled Rack-mount Flange Location and Slot Types on the Switch 4007R 8-slot Chassis Using the Chassis Rack-mount Template Use the paper rack-mount chassis template (which is an accurate copy of the chassis rack-mount flange) to help you position the mountin...

Quick Installation Guide 13 To install the mounting shelves, follow these steps: 1 Obtain the chassis rack-mount template, two mounting shelves, four screws, and four clip nuts (optional) that you received in the shipping box. 2 Locate where you want to install the mounting shelves. a While you hold...

14 Quick Installation Guide c Insert the alignment pin (Figure 9) into the rack slot. If the rack you are using to install the chassis is not threaded, apply pressure and push up on the mounting shelf to align the hole properly with the rack slot hole. The alignment pin on the mounting shelf will th...

Quick Installation Guide 15 Installing the Chassis This section describes how to install the chassis: ■ In a rack without clip nuts ■ In a rack with clip nuts ■ On a table or a shelf You may have other types of racks at your site. Follow the manufacturer’s suggested installation procedures. Before y...

16 Quick Installation Guide 6 Two people lift the chassis through the front of the rack and onto the mounting shelves. Continue to support the chassis until after you have securely installed at least four of the eight screws (two screws per rack-mount flange) for the chassis. 7 Slide the chassis int...

Quick Installation Guide 17 To prevent the plastic label bezel from being damaged, do not attach it to the chassis until after you have installed all components into the chassis and you are ready to power on the Switch. 1 Obtain the chassis rack-mount template that you received in the shipping box. ...

18 Quick Installation Guide 8 Secure the chassis to the rack with the screws provided (eight 10-32 inch screws) and with the rack-mount clips. a Install one screw on each side in the bottom slot on each rack-mount flange. b Allow the weight of the chassis to rest on the mounting shelves and install ...

Quick Installation Guide 19 3 Position the chassis on its side so that you can access the bottom of the chassis. 4 Remove the four feet and the four screws from the hardware kit. 5 Using a flat-blade screwdriver, screw the feet to the bottom of the chassis. See Figure 11. Figure 11 Attaching Plastic...

20 Quick Installation Guide Figure 2. If you need more details about each setup task, see the indicated Switch 4007R documents. Locating 3Com User Documentation The Switch 4007R Getting Started Guide is available in Adobe Acrobat Portable Document Format (PDF) format on the Switch 4007R Documentatio...