3Com 3C17261 - Manual
3Com 3C17261 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – AFETY
- Page 4 – Activating the Module; 0GBASE-CX4 transceiver; Removing the Transceiver; NSTALLATION
- Page 5 – Troubleshooting XENPAK Transceivers; Invalid transceiver fitted; Environmental; XENPAK T
- Page 6 – Com Knowledgebase
- Page 7 – Telephone Technical Support and Repair
- Page 8 – End of Life Statement; Documentation Feedback; EGAL
The 10 Gigabit Module (3C17261) provides your 3Com
SuperStack 4 Switch 5500G-EI Family unit with one 10
Gigabit Ethernet port. The Module conforms to the 10
Gigabit Ethernet standard, IEEE 802.3ae, when it is fitted
with an approved XENPAK transceiver. The Module only
operates at 10 Gbps in full duplex mode.
The Module supports pluggable XENPAK transceivers.
This allows you to provide 10 Gigabit/sec connectivity
between a Switch 5500G-EI Family unit and another
switch using the 10 Gigabit Ethernet standard.
3Com recommends that you only use XENPAK
transceivers supplied by 3Com. If the transceiver is not a
supported media type, it will not be recognised by the
Switch.
Auto-negotiation is not supported in the 10 Gigabit
Ethernet standard, IEEE 802.3ae. The flow control setting
must be manually configured. Flow control is disabled by
default.
LEDs
You can gather information about the status of the
Module using the Module LEDs on the front of the
Switch and the Port LED on the Module.
I
NTRODUCTION
LEDs
Color
Indicates
Module LED
Port ‘Status’
Green
1000Mbps link is present and enabled.
Green flashing
(irregular)
On for 30ms for every packet in full
duplex.
Yellow flashing
The port has failed POST.
Off
No link is present.
Power/Self Test
Green
The module has passed POST and is
operating normally.
Green flashing
Self Test (POST) or Software Download is
in progress.
Red
The module is faulty.
Off
The module has a power fault.
Front Panel LED
Green
The Module is installed and supported.
Yellow flashing The Module is installed but not supported
or has failed POST.
Off
The Module is not installed.
1
3Com
®
SuperStack 4 Switch 5500G 1-Port 10 Gigabit Module (3C17261)
User Guide
DUA1726-1AAA01
3C17261
SuperStack
4 Switch
5500G
Port 10G
Module
1
PWR
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Be sure you follow all safety precautions when you install or replace the Module or an XENPAK Transceiver. To avoid electric shocks and burns to yourself and damage to the equipment, read and follow these warnings: WARNING : When the system is on: Never insert a metal object such as a screwdriver ...
Handling the Module The Module can be easily damaged by electrostatic discharge. To prevent damage, observe the following: Always wear an anti-static wristband connected to a suitable earth point. Do not remove the Module from its packaging until you are ready to install it into a Switch. Do n...
The 3Com approved XENPAK transceivers are: 10GBASE-CX4 (3CXENPAK95) 10GBASE-ER (3CXENPAK96) 10GBASE-LR (3CXENPAK92) To access the latest list of approved XENPAK transceivers for the Module on the 3Com Corporation World Wide Web site, enter this URL into your Internet browser: http://www.3com.c...
